Delta 22-610 - Manual - manualsarea.com

Page 3 - SAFETY GUIDELINES - DEFINITIONS; CALIFORNIA PROPOSITION 65

3 Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, may result in mi...

Page 4 - GENERAL SAFETY RULES

4 GENERAL SAFETY RULES READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT. Failure to follow all instructions listed below, may result in electric shock,fire, and/or serious personal injury or property damage. IMPORTANT SAFETY INSTRUCTIONS 1. FOR YOUR OWN SAFETY,...

Page 6 - FUNCTIONAL DESCRIPTION; GROUNDING INSTRUCTIONS

6 A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-prong grounding type plugs and matching receptacle which will...

Page 7 - UNPACKING AND CLEANING; CARTON CONTENTS

7 UNPACKING AND CLEANING Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating fromall unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gaso-line or lacquer thinner for this purpose...

Page 8 - ASSEMBLY; ASSEMBLY TOOLS REQUIRED; ELECTRICAL CONNECTIONS

8 ASSEMBLY ASSEMBLY TOOLS REQUIRED ASSEMBLY TIME ESTIMATE - 2-3 hours * Open end wrenches (supplied)* Hex wrenches (supplied)* Flat screwdriver (not supplied) UNLOADING ANDPOSITIONING MACHINE This machine should be unloaded using a crane andslings around and under the table on both sides, asshown in...

Page 9 - OVERLOAD PROTECTION

9 To connect power to your machine, proceed as followsfor either 200-230/460 volts, three phase operation. 1. Remove the four screws, one of which is shown at (A) Fig. 4, and remove cover (B). 2. Insert power line through entrance hole (E) and con- nect the three power lines to terminals L1, L2 and ...

Page 10 - OPERATION; OPERATIONAL CONTROLS AND ADJUSTMENTS; STARTING AND STOPPING THE PLANER; FEED ROLL SPEED CONTROLS

10 OPERATION OPERATIONAL CONTROLS AND ADJUSTMENTS STARTING AND STOPPING THE PLANER The machine is started by pressing the green (shroud-ed) "ON" button (A) and stopped by pressing the red(mushroom type) "OFF" button (B), as shown in Fig. 8. Fig. 8 TABLE RAISING ANDLOWERING CONTROLS D...

Page 14 - LEVELING THE TABLE

14 Fig. 21 Fig. 22 Fig. 22A LEVELING THE TABLE The table must be parallel to the cutterhead knives. Tocheck and adjust, proceed as follows: 1. DISCONNECT MACHINE FROM POWER SOURCE 2. Remove the four screws that attach the top cover to the planer and carefully remove the top cover. 3. Place a straigh...

Page 16 - ADJUSTING PRESSURE BAR

16 Fig. 24B Fig. 25 Fig. 26 ADJUSTING PRESSURE BAR IMPORTANT: THE PRESSURE BAR IS SET AT THE FACTORY AND SHOULD NOT NEED ASJUSTMENT.BUT WHEN KNIVES ARE SHARPENED ORREPLACED THE PRESSURE BAR SETTING SHOULDBE CHECKED AND ADJUSTED IF NECESSARY. The pressure bar is located directly behind the cutter-hea...

Page 17 - ADJUSTING THE CHIPBREAKER

17 ADJUSTING THE CHIPBREAKER The chipbreaker is located on the top of the planer andextends down around the front of the cutterhead. Thechip-breaker segments raise as stock is fed through and"break or curl" the chips the same as the plane iron capon a hand plane. The bottom of the chipbreake...

Page 18 - ADJUSTING OUTFEED ROLLER

18 ADJUSTING SPRING TENSION ON FEED ROLLERS The outfeed roll (A) Fig. 33, and infeed roll (not visible)are those parts of your planer that feed the stock whileit is being planed. The feed rolls are under spring tensionand this tension must be sufficient to feed the stock uni-formly through the plane...

Page 19 - ADJUSTING CHIP DEFLECTOR; ADJUSTING TABLE HEIGHT SCALE; GAUGE BLOCK

19 Fig. 38 Fig. 39 Fig. 40 ADJUSTING CHIP DEFLECTOR 1. DISCONNECT MACHINE FROM POWER SOURCE 2. Remove the cutterhead guard. 3. The edge (C) of the chip deflector (A) Fig. 38, should be adjusted so it is a minimum of .040" and a maximumof .080" away from the cutting circle. Place a feelergaug...

Page 20 - MACHINE USE; TROUBLESHOOTING; LUBRICATION

20 When using your machine, follow these few simple steps for achieving the best results. 1. True Up One Face – Feed one face of the board over a jointer, making thin cuts with each pass, until the entire surface is flat. 2. Plane to Thickness – Place the side you planed in STEP 1 face down and feed...

Page 21 - PARTS, SERVICE OR WARRANTY ASSISTANCE; ACCESSORIES; Two Year Limited New Product Warranty; WARRANTY; KEEP MACHINE CLEAN; FAILURE TO START; PROTECTING CAST IRON FROM RUST

21 PARTS, SERVICE OR WARRANTY ASSISTANCE All Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof Porter-Cable • Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional information regarding your Delta quality pro...

Page 22 - NOTES

Page 24 - DELTA SERVICE CENTERS; CANADIAN PORTER-CABLE

The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II...

Delta 22-610 - Manual

Table of Contents:

Summary

Other Delta Models