Cisco SFS 3001 - Manuals

Cisco SFS 3001 – Manual in PDF format online.

Manuals:

Manual

Manual Cisco SFS 3001

Summary

Page 3 - iii; Contents

iii Contents Regulatory Notices .......................................... v FCC Statement .............................................................................................................................................vSafety Information ...................................................

Page 4 - iv

iv Launch Chassis Manager ...........................................................................................................................11Configure Additional Settings ...................................................................................................................12(O...

Page 5 - Regulatory Notices; FCC Statement; Electrical Cautions

v Regulatory Notices FCC Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commer...

Page 7 - vii; General Cautions; Laser Cautions

vii CAUTION: Never place your hand inside an empty card or module bay. You should never have cause to place a hand anywhere inside the Topspin chassis. Unused card and module bays should always have a Topspin cover over the bay to ensure proper safety, ventilation, and cooling. General Cautions CAUT...

Page 8 - viii; Laser Specs; Contact Information

viii Laser Specs Contact Information Table III-1: Topspin P/N Application Optical Parameters 48-00001-01 Fibre Channel *CDRH/IEC Laser Class: 1/1 Maximum Data Rate: 2.125 GB/s Wavelength: 850nm I/O connector: * Standards used: CDRH - 21CFR Chapter I §1040.10; IEC - IEC60825-1:1994 Table III-2: Custo...

Page 9 - Topspin 90 Quick Start; Prepare the Site

1 1 Topspin 90 Quick Start This document describes the basic steps required to install and configure the Topspin 90 system. For more detailed information about the Topspin 90 server switch, we recommend that you have the Topspin 90 Hardware Guide available. • “Prepare the Site” on page 1 • “Install ...

Page 10 - Install the Topspin 90 in an Equipment Rack; Requirements

2 5. Prepare the physical environment for the Topspin 90. a. Make sure that you have an approved grounding wrist-strap. b. Make sure the system has the right cables and sufficient ventilation.c. Unpack the Topspin 90 package, using the packing list provided. d. Verify that you have all of the items ...

Page 13 - Cable the Switch; Connect Management Ports

5 If the brackets do not slide easily, the alignment may be off. Pull the switch back toward you and realign the brackets. Figure 1-5: Sliding the Switch Into the Rack 8. Secure the switch with your screws through the front of the rack, as show in Figure 1-6 . Figure 1-6: Secure Switch with Screws t...

Page 14 - Configure Basic Connectivity; Assigning an Address Statically

6 Connect InfiniBand Cables 1. Plug InfiniBand Cables from the InfiniBand-enabled host to the InfiniBand switch ports. This can also be done in a later step. Refer to step 5 . 2. Plug InfiniBand cables from the Topspin 90 to any additional InfiniBand switches that you want to connect. (Optional) Con...

Page 16 - Connect and Configure InfiniBand Hosts

8 f. Enter the option dhcp command. The chosen method will be persistent across module reboots. g. Enable the management port by entering the no shutdown command. h. Save the configuration to preserve it between reboots. i. Use the show interface mgmt-ethernet command to view your IP address:. Conne...

Page 19 - Launch Chassis Manager

11 • 300 Mhz processor • 800x600 screen resolution, 16bit color depth 2. Insert the Topspin CD-ROM into the CD-ROM drive of a server that has network access to a Topspin management port. 3. Access the top folder of the CD-ROM. The GUI can be found in the following location on the CD-ROM.• Linux/inst...

Page 20 - Configure Additional Settings

12 4. Chassis Manager loads in your browser window. Figure 1-10: Chassis Manager Opening Display for the Topspin 90 Server Switch Configure Additional Settings You can now fully manage the device with CLI over Telnet/SSH or the GUI.1. Verify that you are running the latest version of software. a. Re...

Page 21 - (Optional) Configure the Ethernet Gateway; Layer 2 Bridging Procedure

13 • In the CLI, enter the configuration mode and enter the ntp command with the IP address of the NTP server. Example 3. Configure administrators and privilege levels. See Creating User Accounts in the User Guide . (Optional) Configure the Ethernet Gateway Configure the Ethernet Gateway if you have...

Page 23 - Configure the Fibre Channel Gateway (Optional)

15 Configure the Fibre Channel Gateway (Optional) To configure ITLs, perform the following steps:1. Log in to your host.2. Enter the /etc/init.d/ts_srp stop command at the host CLI to force the host to log out of any storage. You must disable connections now and enable them later in this process. 3....

Page 29 - Index

Index B basic connectivity ...................................................6 C chassis manager launching .........................................................11 configure basic connectivity ...................................6 connectivity, basic .................................................