Cisco N55M4Q - Manuals - manualsarea.com

Page 3 - Installation Guidelines; Before installing the switch, these guidelines must be met:

2-3 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Preparing for Installation Warning For connections outside the building where the equipment is installed, the following ports must be connected through an approved network termination unit wit...

Page 4 - “SFP Module; Equipment That You Supply; Powering the Switch

2-4 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Powering the Switch • Temperature around the unit does not exceed 113°F (45°C). If the switch is installed in a closed environment or in a multirack assembly, the temperature around it might b...

Page 5 - Note; Verifying Switch Operation; “Mounting the Switch” section on; Mounting the Switch; On a Desk or Shelf (without Mounting Screws)

2-5 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Verifying Switch Operation Note You can use both the uplink port and the auxiliary power adapter. However, the auxiliary power input takes precedence. Catalyst 3560CPD-8PT-S • Connect a 10/100...

Page 7 - Installing the Mounting Screws on Top of a Desk or a Shelf; Remove the screw template from the desk or shelf.

2-7 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Mounting the Switch Figure 2-1 Installing the Mounting Screws on Top of a Desk or a Shelf Step 3 Peel the adhesive strip off the bottom of the screw template, and attach it to the top of the d...

Page 8 - Mounting the Switch on Top of a Desk or Shelf; “After Installing the Switch” section on page 2-31

2-8 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Mounting the Switch Figure 2-2 Mounting the Switch on Top of a Desk or Shelf After you mount the switch, see the “After Installing the Switch” section on page 2-31 for information about config...

Page 9 - Installing the Mounting Screws Under a Desk or Shelf; Remove the screw template from underneath the desk or shelf.

2-9 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Mounting the Switch Figure 2-3 Installing the Mounting Screws Under a Desk or Shelf Step 4 Use a 0.144-inch (3.7 mm) or a #27 drill bit to drill a 1/2-inch (12.7 mm) hole in the three screw te...

Page 10 - Mounting the Switch Under a Desk or Shelf

2-10 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Mounting the Switch Figure 2-4 Mounting the Switch Under a Desk or Shelf After you mount the switch, see the “After Installing the Switch” section on page 2-31 for information about configuri...

Page 11 - Location of the Mounting Holes on the Switch; Switch

2-11 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Mounting the Switch Step 1 Locate the screw template. The template is used to align the mounting screw holes. Note Figure 2-5 shows the measurements for the location of the screws on the swit...

Page 12 - Installing the Mounting Screws on the Wall

2-12 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Mounting the Switch Figure 2-6 Installing the Mounting Screws on the Wall Figure 2-7 Installing the Switch on a Wall Step 8 Place the switch onto the mounting screws, and slide it down until ...

Page 13 - With a Mounting Tray; Mounting Tray with Screws; Caution; Attaching the Tray to the Desk or Shelf

2-13 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Mounting the Switch With a Mounting Tray The mounting kit (part number CMP-MGNT-TRAY=) is optional. You can order it when you order your switch, or you can order it later from your Cisco repr...

Page 14 - Installing the Switch on the Mounting Tray

2-14 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Mounting the Switch Step 4 Place the switch onto the mounting screws, and slide the switch until it locks into place. See Figure 2-9 . Figure 2-9 Installing the Switch on the Mounting Tray 1 ...

Page 15 - Securing the Mounting Tray to the Switch; Warning; Mounting Tray with a Magnet

2-15 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Mounting the Switch Step 5 Use the two number-10 Phillips pan-head screws to secure the mounting tray to the switch. See Figure 2-10 . Figure 2-10 Securing the Mounting Tray to the Switch War...

Page 16 - Place the switch on the mounting tray. See; Placing the Switch on the Mounting Tray; the magnet and switch on a metal wall.

2-16 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Mounting the Switch Step 1 Place the switch on the mounting tray. See Figure 2-11 . Figure 2-11 Placing the Switch on the Mounting Tray Step 2 Use the two number-10 Phillips pan-head screws t...

Page 17 - Wall-Mounting with a Magnet

2-17 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Mounting the Switch Warning Read the wall-mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result i...

Page 18 - In a Rack; Attaching Brackets to the Switch, page 2-18; Attaching Brackets to the Switch; attach the second bracket to the opposite side.; Attaching the 19-inch Brackets for Rack-Mounting

2-18 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Mounting the Switch In a Rack Installing the switch in a rack requires an optional bracket kit that is not included with the switch. You can order these kits from your Cisco representative: •...

Page 19 - Attaching the 23-inch Brackets for Rack-Mounting; Mounting the Switch in a Rack

2-19 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Mounting the Switch Figure 2-15 shows how to attach a 23-inch bracket to one side of the switch. Follow the same steps to attach the second bracket to the opposite side. Figure 2-15 Attaching...

Page 20 - On a DIN Rail; DIN rail mount; Attaching the DIN-Mount Tray to the Switch; Place the switch on the DIN rail mount. See; Placing the Switch on the DIN-Mount Tray

2-20 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Mounting the Switch On a DIN Rail The DIN-mount kit (part number CMP-DIN-MNT=) is optional. You can order it when you order your switch, or you can order it later from your Cisco representati...

Page 21 - Securing the DIN-Mount Tray to the Switch; Mounting the Switch on a DIN Rail

2-21 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Mounting the Switch Step 2 Use the two number-10 Phillips pan-head screws to secure the DIN rail mount to the switch. See Figure 2-18 . Figure 2-18 Securing the DIN-Mount Tray to the Switch M...

Page 22 - After you install the switch, see the

2-22 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Mounting the Switch Figure 2-19 Mounting the Switch on a DIN Rail Step 2 Rotate the switch down toward the DIN rail until the release tabs on the DIN rail mount clicks. Step 3 Lift lightly on...

Page 23 - Removing the Switch from a DIN Rail; Switch Removal

2-23 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Mounting the Switch Removing the Switch from a DIN Rail Step 1 Ensure that power is removed from the switch, and disconnect all cables and connectors from the front panel of the switch. Step ...

Page 24 - Installing a Cover for the Reset Button (Optional); Reset Cover on the Catalyst 2960CPD-8PT-L Switch

2-24 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Installing a Cover for the Reset Button (Optional) Installing a Cover for the Reset Button (Optional) You can cover the reset button to prevent accidental or unauthorized reset of your switch...

Page 25 - Installing the Power Cord Retainer (Optional); Inserting the Retainer through the Lanced Loop; AC power cord

2-25 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Installing the Power Cord Retainer (Optional) Installing the Power Cord Retainer (Optional) Note This section applies to switches with an AC power connector. The power cord retainer part numb...

Page 26 - Sliding the Retainer Through the Latch

2-26 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Installing the Power Cord Retainer (Optional) Step 3 Slide the retainer through the first latch. See Figure 2-24 . Figure 2-24 Sliding the Retainer Through the Latch Step 4 Slide the retainer...

Page 27 - Sleeve Around the Power Cord; Secure the AC power cord by pressing on the retainer. See; Securing the Power Cord in the Retainer; Sleeve for thin power cords

2-27 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Installing the Power Cord Retainer (Optional) Figure 2-26 Sleeve Around the Power Cord Step 6 Secure the AC power cord by pressing on the retainer. See Figure 2-27 . Figure 2-27 Securing the ...

Page 28 - Using the Washer; Washer

2-28 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Installing the Cable Guard (Optional) Installing the Cable Guard (Optional) The cable guard prevents tampering with the cables after the cables are installed. The cable guard (CMP-CBLE-GRD=) ...

Page 29 - Attaching the Cable Guard to the Switch; Attach the cables to the switch. See; Cable guard

2-29 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Installing the Cable Guard (Optional) Step 2 Use the supplied number-10 pan-head screws to attach the cable guard to the switch. See Figure 2-29 . Figure 2-29 Attaching the Cable Guard to the...

Page 30 - Attaching the Cables to the Switch

2-30 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Installing the Cable Guard (Optional) Figure 2-31 Attaching the Cables to the Switch Step 4 Guide the connected cables through the slots in the front of the cable guard. Slide the cable guide...

Page 31 - Securing the Cable Guard to the Desk; After Installing the Switch; “Verifying Switch Operation” section on page 2-5; Installing SFP Modules

2-31 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation After Installing the Switch Step 5 (Optional) To attach the cable guard to the desk or wall, use a 0.144-inch (3.7 mm) or a #27 drill bit to drill 1/2-inch (12.7 mm) holes at each of the two ...

Page 32 - Installing an SFP Module; Removing SFP Modules; Insert a dust plug into the optical ports of the SFP module.

2-32 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Removing SFP Modules Warning Class 1 laser product. Statement 1008 Step 1 Attach an ESD-preventive wrist strap to your wrist and to a bare metal surface. Step 2 Find the send (TX) and receive...

Page 33 - Removing a Bale-Clasp Latch SFP Module; Connecting Devices to the Ethernet Ports; If auto-MDIX is disabled, use the guidelines in

2-33 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Connecting Devices to the Ethernet Ports Figure 2-35 Removing a Bale-Clasp Latch SFP Module Connecting Devices to the Ethernet Ports • Connecting to the 10/100 and 10/100/1000 Ports, page 2-3...

Page 34 - Connecting to an Ethernet Port; Connecting to the PoE Ports; Device

2-34 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Connecting Devices to the Ethernet Ports Figure 2-36 Connecting to an Ethernet Port Connecting to the PoE Ports The 10/100 PoE ports have the same autonegotiation settings and cabling require...

Page 35 - Where to Go Next; “Management Options”

2-35 Catalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02 Chapter 2 Switch Installation Where to Go Next restricted access location and users and service people who are authorized within the restricted access location are made aware of the hazard. A restricted access area can be...