Cisco Cisco ONS 15454 SDH - Manuals

Cisco Cisco ONS 15454 SDH – Manual in PDF format online.

Manuals:

Manual

Manual Cisco Cisco ONS 15454 SDH

Summary

Page 2 - NTP-D24 Verify Card Installation; Purpose; Security Level

4-2 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node NTP-D24 Verify Card Installation 8. NTP-D170 Create Protection Groups, page 4-26 —Complete this procedure, as needed, to set up 1:1, 1:N, 1+1, or Y-cable protection groups for ONS 15454 SDH electrical and optical cards...

Page 4 - NTP-D30 Create Users and Assign Security; DLP-D74 Create a New User—Single Node

4-4 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node NTP-D30 Create Users and Assign Security NTP-D30 Create Users and Assign Security Step 1 Complete the “DLP-D60 Log into CTC” task on page 3-24 at the node where you want to create users. If you are already logged in, c...

Page 5 - DLP-D75 Create a New User—Multiple Nodes

4-5 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D75 Create a New User—Multiple Nodes • Password—Type the user password. The password must be a minimum of six and a maximum of20 alphanumeric (a-z, A-Z, 0-9) and special (+, #, %) characters, where at least two cha...

Page 7 - In the confirmation dialog box, click Yes.

4-7 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node NTP-D25 Set Up Name, Date, Time, and Contact Information Tip You can also position nodes manually on the network view map. Press Ctrl then drag and dropthe node icon. To create a logical network map for all ONS 15454 S...

Page 8 - NTP-D279 Set Power Monitor Thresholds

4-8 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node NTP-D279 Set Power Monitor Thresholds Step 6 Review the node information. If you need to make corrections, repeat Steps 3 through 5 to enter the corrections. If the information is correct, continue with the “NTP-D279 S...

Page 9 - NTP-D169 Set Up CTC Network Access

4-9 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node NTP-D169 Set Up CTC Network Access NTP-D169 Set Up CTC Network Access Step 1 Complete the “DLP-D60 Log into CTC” task on page 3-24 . If you are already logged in, continue with Step 2 . Step 2 Complete the “DLP-D249 Pr...

Page 10 - DLP-D249 Provision IP Settings

4-10 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D249 Provision IP Settings DLP-D249 Provision IP Settings Caution All network changes should be approved by your network (or LAN) administrator. Step 1 If you are in network view, switch to node view by double-cli...

Page 11 - Click Yes on the confirmation dialog box.

4-11 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D249 Provision IP Settings • MAC Address—(Display only.) Displays the ONS 15454 SDH IEEE 802 MAC address. • Net/Subnet Mask Length—Type the subnet mask length (decimal number representing the subnetmask length in ...

Page 12 - Reboot Activity

4-12 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D249 Provision IP Settings Step 5 Click OK. The network view appears. The node icon appears in gray, during which time you cannotaccess the node. Step 6 Double-click the node icon when it becomes green. As necessa...

Page 14 - Press the Status button to choose the Save Configuration option.

4-14 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D64 Set the IP Address, Default Router, and Network Mask Using the LCD Figure 4-2 Changing the IP Address Step 4 Push the Slot button to move to the IP address or subnet mask digit you need to change. The selected...

Page 15 - DLP-D65 Create a Static Route

4-15 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D65 Create a Static Route Step 10 Return to your originating procedure (NTP). DLP-D65 Create a Static Route Step 1 In node view, click the Provisioning > Network tabs. Step 2 Click the Static Routing tab. Click...

Page 16 - DLP-D250 Set Up or Change Open Shortest Path First Protocol

4-16 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D250 Set Up or Change Open Shortest Path First Protocol DLP-D250 Set Up or Change Open Shortest Path First Protocol Step 1 In node view, click the Provisioning > Network > OSPF tabs. Step 2 On the top left s...

Page 18 - DLP-D251 Set Up or Change Routing Information Protocol

4-18 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D251 Set Up or Change Routing Information Protocol • Retransmit Int (sec)—Sets the time that will elapse before a packet is resent. Five seconds is thedefault. • Dead Int (sec)—Sets the number of seconds that will...

Page 19 - NTP-D27 Set Up the ONS 15454 SDH for Firewall Access

4-19 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node NTP-D27 Set Up the ONS 15454 SDH for Firewall Access Step 6 If you want to complete an address summary, complete the following steps. If not, continue with Step 7 . Complete the address summary only if the ONS 15454 S...

Page 20 - DLP-D67 Provision the IIOP Listener Port on the ONS 15454 SDH

4-20 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D67 Provision the IIOP Listener Port on the ONS 15454 SDH Step 3 If the CTC computer resides behind a firewall, complete the “DLP-D68 Provision the IIOP Listener Port on the CTC Computer” task on page 4-22 . Figur...

Page 21 - Port

4-21 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D67 Provision the IIOP Listener Port on the ONS 15454 SDH Step 3 Click Apply. Step 4 When the Change Network Configuration message appears, click Yes. Both ONS 15454 SDH TCC2s reboot, one at a time. The reboot tak...

Page 22 - DLP-D68 Provision the IIOP Listener Port on the CTC Computer; NTP-D28 Set Up Timing

4-22 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D68 Provision the IIOP Listener Port on the CTC Computer DLP-D68 Provision the IIOP Listener Port on the CTC Computer Step 1 In node view, from the Edit menu, choose Preferences. Step 2 In the Preferences dialog b...

Page 23 - DLP-D69 Set Up External or Line Timing

4-23 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D69 Set Up External or Line Timing Step 1 Complete the “DLP-D60 Log into CTC” task on page 3-24 the ONS 15454 SDH node where you want to set up timing. If you are already logged in, continue with Step 2. Step 2 Co...

Page 25 - DLP-D70 Set Up Internal Timing

4-25 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D70 Set Up Internal Timing – Timing Mode set to Line—Your options are the node’s working OC-N cards (non-DWDMnodes), or OSC cards (DWDM nodes) and Internal Clock. Select the cards/ports that are directlyor indirec...

Page 26 - NTP-D170 Create Protection Groups

4-26 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node NTP-D170 Create Protection Groups • E1, 2.048 MHz, 64 KHz—Choose E1, 2.048 MHz, or 64 KHz depending on the signal supportedin your market. For example, 64 KHz is used in Japan. E1, 2.048 MHz, and 64 KHz are physicalsi...

Page 27 - Type

4-27 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node NTP-D170 Create Protection Groups Table 4-3 describes the protection types available on the ONS 15454 SDH. Stop. You have completed this procedure. Table 4-3 Card Protection Types Type Cards Description and Installati...

Page 31 - DLP-D252 Create a Y-Cable Protection Group

4-31 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D252 Create a Y-Cable Protection Group DLP-D252 Create a Y-Cable Protection Group Step 1 Verify that the transponder or muxponder cards are installed according to the Y-cable requirementsspecified in Table 4-3 on ...