Cisco Cisco 10000 ESR - Manuals

Cisco Cisco 10000 ESR – Manual in PDF format online.

Manuals:

Manual

Manual Cisco Cisco 10000 ESR

Summary

Page 2 - Product Description; Figure 1

Product Description 2 Cisco 10000 ESR AC Power Entry Module Installation 78-10832-01 Product Description The AC PEM provides power conversion directly from the facility VAC input power (100 VAC to 240 VAC) to the –48V VDC used internally by the system (see Figure 1). AC power is delivered to the AC ...

Page 3 - Prerequisites and Preparation; Safety Guidelines; Safety Warnings

3 Cisco 10000 ESR AC Power Entry Module Installation 78-10832-01 Prerequisites and Preparation Prerequisites and Preparation Before you perform any of the procedures in this guide, Cisco recommends that you: • Read the safety guidelines in the next section and review the electrical safety and ESD-pr...

Page 4 - Warning; Installation Guidelines; Required Tools and Equipment; You need the following tools and equipment to install an AC PEM:

Installation Guidelines 4 Cisco 10000 ESR AC Power Entry Module Installation 78-10832-01 Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with ...

Page 5 - Adding or Replacing an AC PEM; Removing the Front Cover, page 5; Removing the Front Cover; Figure 2

5 Cisco 10000 ESR AC Power Entry Module Installation 78-10832-01 Adding or Replacing an AC PEM Adding or Replacing an AC PEM This section describes how to add or replace an AC PEM in the Cisco 10000 chassis. It contains the following procedures: • Removing the Front Cover, page 5 • Installing a Seco...

Page 6 - Figure 3; Continue installing or replacing the AC PEM:

Adding or Replacing an AC PEM 6 Cisco 10000 ESR AC Power Entry Module Installation 78-10832-01 Step 2 Remove the cover by lifting it up slightly and then pulling it toward you (Figure 3). Figure 3 Removing the Front Cover Step 3 Continue installing or replacing the AC PEM: • If you are installing a ...

Page 7 - Installing a Second AC PEM; Figure 4; ESD

7 Cisco 10000 ESR AC Power Entry Module Installation 78-10832-01 Adding or Replacing an AC PEM Installing a Second AC PEM Use the following procedure to install a second AC PEM in the bottom power bay for redundancy. Step 1 Attach an antistatic wrist strap to your wrist and to an ESD socket on the c...

Page 8 - Figure 5; Captive

Adding or Replacing an AC PEM 8 Cisco 10000 ESR AC Power Entry Module Installation 78-10832-01 Step 2 Loosen the captive screws to remove the blank cover from the bottom power bay (Figure 5). Figure 5 Removing the Blank Cover 1 3 2 4 0A PROCESSOR PROCESSOR FANS OK FAN FAILURE MULTI- FAN FAILURE When...

Page 9 - Figure 6

9 Cisco 10000 ESR AC Power Entry Module Installation 78-10832-01 Adding or Replacing an AC PEM Step 3 Install the new AC PEM all the way into the power bay to ensure a secure connection to the backplane, and then tighten the captive screws (Figure 6). Figure 6 Installing an AC PEM 1 3 2 4 0A PROCESS...

Page 10 - Figure 7; Plug the facility AC input power cord into a power receptacle.

Adding or Replacing an AC PEM 10 Cisco 10000 ESR AC Power Entry Module Installation 78-10832-01 Step 4 Connect the power cord from the PEM to your power cord that connects to the facility VAC input. Step 5 Set the AC power cord connectors in a cord strain relief (canoe) to prevent them from accident...

Page 11 - The (green) power LED on the PEM lights indicating that the PEM is on.; Figure 8; Replace the front cover.

11 Cisco 10000 ESR AC Power Entry Module Installation 78-10832-01 Adding or Replacing an AC PEM Step 7 Set the power switch to the on (|) position (Figure 8). The (green) power LED on the PEM lights indicating that the PEM is on. Figure 8 Setting the AC Power Switch to the On Position Step 8 Replace...

Page 12 - Replacing an AC PEM; Use the following procedure to replace an AC PEM.; Figure 9

Adding or Replacing an AC PEM 12 Cisco 10000 ESR AC Power Entry Module Installation 78-10832-01 Replacing an AC PEM Use the following procedure to replace an AC PEM. Note The illustrations in this guide show how to replace the AC PEM from the bottom power bay. The procedure is the same to replace an...

Page 13 - Caution; Setting the AC Power Switch to the Off Position

13 Cisco 10000 ESR AC Power Entry Module Installation 78-10832-01 Adding or Replacing an AC PEM Step 2 Power off the PEM you are replacing (Figure 10). Caution Do not power off both AC PEMs in a redundant system or the system shuts down and all data traffic stops. Only power off the AC PEM you are r...

Page 14 - AC Power Cord Connectors in Canoes

Adding or Replacing an AC PEM 14 Cisco 10000 ESR AC Power Entry Module Installation 78-10832-01 Step 3 Remove the PEM power cable from its canoe and disconnect it from the AC input power cable (Figure 11). Figure 11 AC Power Cord Connectors in Canoes 32235 1 3 2 4 0A PROCESS OR ONLY 0B 5 6 7 8 PROCE...

Page 15 - Removing an AC PEM

15 Cisco 10000 ESR AC Power Entry Module Installation 78-10832-01 Adding or Replacing an AC PEM Step 4 Loosen the captive screws on the PEM and remove the PEM from the chassis using the handle on the faceplate (Figure 12). Figure 12 Removing an AC PEM 1 3 2 4 0A PROCESSOR PROCESSOR FANS OK FAN FAILU...

Page 16 - Installing an AC PEM

Adding or Replacing an AC PEM 16 Cisco 10000 ESR AC Power Entry Module Installation 78-10832-01 Step 5 Install the new PEM all the way into the power bay to ensure a good connection to the backplane, and tighten the captive screws on the PEM (Figure 13). Figure 13 Installing an AC PEM 1 3 2 4 0A PRO...

Page 18 - Setting the AC Power Switch to the On Position

Adding or Replacing an AC PEM 18 Cisco 10000 ESR AC Power Entry Module Installation 78-10832-01 Step 9 Set the power switch to the on (|) position (Figure 15). The (green) power LED on the PEM lights indicating that the PEM is on. Figure 15 Setting the AC Power Switch to the On Position Step 10 Repl...

Page 19 - Troubleshooting the Installation; Table 1 contains troubleshooting information for the AC PEM:; Table 1; Symptom; System fails to power on

19 Cisco 10000 ESR AC Power Entry Module Installation 78-10832-01 Adding or Replacing an AC PEM Troubleshooting the Installation Table 1 contains troubleshooting information for the AC PEM: Table 1 AC PEM Troubleshooting Symptom Description System fails to power on Check that: • All AC power cords a...

Page 20 - FCC Class A Compliance; Move the equipment farther away from the television or radio.; Cisco Connection Online

FCC Class A Compliance 20 Cisco 10000 ESR AC Power Entry Module Installation 78-10832-01 FCC Class A Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable prote...

Page 21 - product

21 Cisco 10000 ESR AC Power Entry Module Installation 78-10832-01 Cisco Connection Online Available 24 hours a day, 7 days a week, CCO provides a wealth of standard and value-added services to Cisco customers and business partners. CCO services include product information, product documentation, sof...

Page 22 - Feedback; in the toolbar and select; Documentation; to send it to Cisco.

Documentation CD-ROM 22 Cisco 10000 ESR AC Power Entry Module Installation 78-10832-01 Documentation CD-ROM Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM, a member of the Cisco Connection Family, is updated mo...