Cisco CHAS-7K - Manuals

8 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Prerequisites Lifting the Chassis Safely The chassis weighs 76 pounds when empty (no processor modules or power supplies installed) and145 pounds when fully configured with two power supplies and all interface slots populated.Whenever you ...

Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 9 Prerequisites Safety with Electricity Follow these basic guidelines when working with any electrical equipment: • Before beginning any procedures, locate the emergency power-off switch for the room in whichyou are working. • Never assume t...

10 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Prerequisites • Multimode Fiber Distributed Data Interface (FDDI) connectors use small plastic arms on twosides of the connector that act like springs and are constrained by the inside of the connector port.To remove a multimode cable fro...

Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 11 Unpacking the Chassis Following are guidelines for preventing ESD damage: • Always use an ESD strap and ensure that it makes good skin contact. • When removing or installing an LED board, connect the equipment end of the ground strap to a...

Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 13 Replacing a Rack-Mounted Chassis Adding a New Chassis to the Rack If there is sufficient rack space to install the replacement chassis before you remove the existingsystem, proceed as follows. Step 1 Follow the instructions in the section...

14 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Replacing a Rack-Mounted Chassis Caution To prevent damage, never attempt to lift or support the front of the chassis with the plastic front panels. The panels can break away and allow the chassis to drop. Step 9 To remove the empty chass...

18 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Moving System Components Moving System Components The following sections describe the procedures for removing each processor module and powersupply from the old chassis and installing it in the new chassis. Move and install all processorm...

Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 21 Moving System Components Step 6 While keeping the carrier at a 90-degree orientation to the backplane, carefully slide thecarrier into the slot until the back of the faceplate makes contact with the ejector levers. (SeeFigure 8b.) Step 7 ...

22 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Moving System Components Note Use both hands to handle power supplies. Each weighs 20 pounds. If the power supply resists when you attempt to pull it out of the bay, the switch is probably not fully in the OFF (O) position,or the captive ...

24 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Verifying the Installation Verifying the Installation This section provides instructions for first ensuring that all connections are secure and then forrestarting the system and verifying that it operates correctly. If the system does not...

Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 25 Verifying the Installation Step 2 After turning on the lower power supply, turn ON the upper power supply (if one is present)for redundant power. The upper power LED on the front of the chassis will go on. Step 3 While the system initiali...

26 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Verifying the Installation Troubleshooting the Installation Follow the procedures in this section if the system does not restart and boot as expected. Most often,problems you encounter while replacing the components in a new chassis are c...

28 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Verifying the Installation In systems with a single power supply, and in systems with redundant power when both powersupplies are being shut down, the DC fail (or output fail) LED goes on momentarily as the systemramps down, but goes out ...

30 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Verifying the Installation Route Switch Processor LEDs (Cisco 7507) Figure 16 shows the two LEDs on the RSP2. They indicate the system and RSP2 status. The normalLED goes on to indicate that the system is operational. During normal operat...

Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 31 Verifying the Installation Interface Processor, SP, and SSP LEDs The SP or SSP (on the Cisco 7000) and all interface processors contain an enabled LED. When on,this LED indicates that the SP or interface processor is operational and that ...

32 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Verifying the Installation Step 3 Listen for the system blower. It generates about 60 dB, so you should immediately hear itstart operating. If you determine that the power supplies are functioning normally and thatthe blower is faulty, co...

34 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Verifying the Installation Figure 17 Cisco 7000 Port Configuration Worksheet Circle one: AIP/CIP/EIP/FIP/FSIP/HIP/TRIP 0/0 0/1 0/2 0/3 0/4 0/5 0/6 0/7 Slot 3 3/0 3/1 3/2 3/3 3/4 3/5 3/6 3/7 Slot 4 4/0 4/1 4/2 4/3 4/4 4/5 4/6 4/7 Router na...

36 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Translated Safety Warnings Translated Safety Warnings Following are translations of the safety warnings that appear throughout this publication: Power Disconnection Warning Warning Before working on a system that has an on/off switch, tur...

Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 37 Translated Safety Warnings Varoitus Älä kosketa virtalähdettä virtajohdon ollessa kytkettynä. Virrankatkaisimella varustetuissa järjestelmissä on virtalähteen sisällä jäljellä verkkojännite, vaikka virrankatkaisin onkatkaistu-asennossa vi...

38 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Translated Safety Warnings Attention Avant de travailler sur un châssis ou à proximité d'une alimentation électrique, débrancher le cordon d'alimentation des unités en courant alternatif ; couper l'alimentation des unitésen courant contin...

Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 39 Translated Safety Warnings ¡Advertencia! Puede ser que este equipo posea más de un cable de alimentación. Para reducir el riesgo de descarga eléctrica, desenchufar los dos cables antes de proceder al mantenimiento de launidad. Varning! De...

40 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Translated Safety Warnings Advarsel Det er nødvendig med to personer for å løfte kabinettet. Ta tak i kabinettet under den nedre kanten, og løft med begge hender. Unngå personskade ved å holde ryggen rett og løfte medbena, ikke ryggen. Un...

Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 41 Translated Safety Warnings Avvertenza Prima di svolgere una qualsiasi delle procedure seguenti, verificare che il circuito CC non sia alimentato. Per verificare che tutta l’alimentazione sia scollegata (OFF), individuarel’interruttore aut...

42 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Translated Safety Warnings Chassis Warning—Rack-Mounting and Servicing Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The follow...

Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 43 Translated Safety Warnings Warnung Zur Vermeidung von Körperverletzung beim Anbringen oder Warten dieser Einheit in einem Gestell müssen Sie besondere Vorkehrungen treffen, um sicherzustellen, daß das Systemstabil bleibt. Die folgenden Ri...

Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 45 Translated Safety Warnings Attention Quand des fils torsadés sont nécessaires, utiliser des douilles terminales homologuées telles que celles à circuit fermé ou du type à plage ouverte avec cosses rebroussées. Ces douillesterminales doive...

46 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Translated Safety Warnings Attention La figure illustre le bloc de connexion de l'alimentation en courant continu. Câbler l'alimentation en courant continu en fixant les cosses qui conviennent aux extrémités câbléesconformément au schéma....

48 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Cisco Information Online Cisco Information Online Cisco Information Online (CIO) is Cisco Systems’ primary, real-time support channel. Maintenancecustomers and partners can self-register on CIO to obtain additional content and services. A...