Cisco 5500 - Manuals

Cisco 5500 – Manual in PDF format online.

Manuals:

Manual

Manual Cisco 5500

Summary

Page 2 - Supervisor Engine Module LEDs; Supervisor Engine III Front Panel; Supervisor Engine III and Uplink Module LED Descriptions; LED; Note

7-2 Cisco MGC Software Release 7 Operations, Maintenance, and Troubleshooting Guide OL-0542-06 Chapter 7 Maintaining the Cisco Catalyst 5500 Multiswitch Router Checking Equipment Status Supervisor Engine Module LEDs The front panel of the supervisor engine III (product number WS X5530-E3) is shown i...

Page 3 - Ethernet Switching Module (10BaseT 24 Port) LEDs; Ethernet Switching Module (10BaseT 24 Port) LED Descriptions

7-3 Cisco MGC Software Release 7 Operations, Maintenance, and Troubleshooting Guide OL-0542-06 Chapter 7 Maintaining the Cisco Catalyst 5500 Multiswitch Router Checking Equipment Status Ethernet Switching Module (10BaseT 24 Port) LEDs Each switching module (Prod # WS-X5013) contains a STATUS LED. Wh...

Page 4 - Route Switch Module LEDs

7-4 Cisco MGC Software Release 7 Operations, Maintenance, and Troubleshooting Guide OL-0542-06 Chapter 7 Maintaining the Cisco Catalyst 5500 Multiswitch Router Checking Equipment Status 10/100 Mbps Fast Ethernet Switching Module (10/100BaseTX 12 Port) LEDs The faceplate of each 10/100 Mbps Fast Ethe...

Page 5 - Using the Command Line Interface to Check Status; show; Command Reference Manual; Replacing Hardware Components; Removing and Replacing the Power Supply, page 7-8; LED State

7-5 Cisco MGC Software Release 7 Operations, Maintenance, and Troubleshooting Guide OL-0542-06 Chapter 7 Maintaining the Cisco Catalyst 5500 Multiswitch Router Replacing Hardware Components Using the Command Line Interface to Check Status The Cisco Catalyst 5500 command line interface includes a ser...

Page 6 - Avoiding Problems When Inserting and Removing Modules; Catalyst 5000 Series Module Installation Guide; Tools Required; To remove a supervisor engine, perform the following steps:

7-6 Cisco MGC Software Release 7 Operations, Maintenance, and Troubleshooting Guide OL-0542-06 Chapter 7 Maintaining the Cisco Catalyst 5500 Multiswitch Router Replacing Hardware Components Avoiding Problems When Inserting and Removing Modules The ejector levers on the supervisor engine and switchin...

Page 7 - Place the removed module on an antistatic mat or antistatic foam.; show system; and; show module; commands to; Replacing the Supervisor Engine; Reattach network interface cables to the module ports.

7-7 Cisco MGC Software Release 7 Operations, Maintenance, and Troubleshooting Guide OL-0542-06 Chapter 7 Maintaining the Cisco Catalyst 5500 Multiswitch Router Replacing Hardware Components Step 4 Grasp the handle of the module with one hand and place your other hand under the carrier to support and...

Page 8 - Locating the Flash Memory Card Write-Protection Switch; Do not attempt to force the card past this point.; Removing and Replacing the Power Supply; Flash PC card

7-8 Cisco MGC Software Release 7 Operations, Maintenance, and Troubleshooting Guide OL-0542-06 Chapter 7 Maintaining the Cisco Catalyst 5500 Multiswitch Router Replacing Hardware Components Note You can insert and remove the Flash memory card with the power on. Before you install a card, verify that...

Page 9 - Removing an AC-Input Power Supply; Follow these steps to remove an AC-input power supply:; AC-Input Power Supply Front Panels; Disconnect the power cord from the power source.

7-9 Cisco MGC Software Release 7 Operations, Maintenance, and Troubleshooting Guide OL-0542-06 Chapter 7 Maintaining the Cisco Catalyst 5500 Multiswitch Router Replacing Hardware Components Removing an AC-Input Power Supply Follow these steps to remove an AC-input power supply: Note In systems with ...

Page 10 - Handling an AC-Input Power Supply; Pull the supply out of the bay and put it aside.; Installing an AC-Input Power Supply; “Removing an

7-10 Cisco MGC Software Release 7 Operations, Maintenance, and Troubleshooting Guide OL-0542-06 Chapter 7 Maintaining the Cisco Catalyst 5500 Multiswitch Router Replacing Hardware Components Figure 7-8 Handling an AC-Input Power Supply Warning Keep your hands and fingers out of the power supply bays...

Page 11 - Cisco Media Gateway Controller Hardware Installation Guide; Removing a DC-Input Power Supply; Warning

7-11 Cisco MGC Software Release 7 Operations, Maintenance, and Troubleshooting Guide OL-0542-06 Chapter 7 Maintaining the Cisco Catalyst 5500 Multiswitch Router Replacing Hardware Components Step 3 Slide the power supply all the way into the power supply bay. Step 4 Using a flat-blade screwdriver, t...

Page 12 - DC-Input Power Supply Front Panels; Loosen and remove the captive screws on the power supply (see; CO ground

7-12 Cisco MGC Software Release 7 Operations, Maintenance, and Troubleshooting Guide OL-0542-06 Chapter 7 Maintaining the Cisco Catalyst 5500 Multiswitch Router Replacing Hardware Components Step 2 Turn the power switch to the OFF (0) position on the power supply you are removing (see Figure 7-9 ). ...

Page 13 - Figure 7-11 Handling a DC Power Supply; Caution; Installing a DC-Input Power Supply; Follow these steps to install a DC-input power supply:

7-13 Cisco MGC Software Release 7 Operations, Maintenance, and Troubleshooting Guide OL-0542-06 Chapter 7 Maintaining the Cisco Catalyst 5500 Multiswitch Router Replacing Hardware Components Warning Keep hands and fingers out of the power supply bays. High voltage is present on the power backplane w...

Page 15 - Figure 7-12 DC-Input Power Supply Connectors; command to display the power supply and system status.; Removing and Replacing the Chassis Fan Assembly; Removing the Fan Assembly

7-15 Cisco MGC Software Release 7 Operations, Maintenance, and Troubleshooting Guide OL-0542-06 Chapter 7 Maintaining the Cisco Catalyst 5500 Multiswitch Router Replacing Hardware Components Figure 7-12 DC-Input Power Supply Connectors Caution In a system with dual power supplies, use the modular po...

Page 16 - Installing the Fan Assembly; Perform the following steps to install the new fan assembly:; Figure 7-13 Cisco Catalyst 5500 Chassis Fan Assembly

7-16 Cisco MGC Software Release 7 Operations, Maintenance, and Troubleshooting Guide OL-0542-06 Chapter 7 Maintaining the Cisco Catalyst 5500 Multiswitch Router Replacing Hardware Components Note The fan assembly is designed to be removed and replaced while the system is operating without presenting...

Page 17 - Checking the Installation; “Obtaining Technical Assistance” section

7-17 Cisco MGC Software Release 7 Operations, Maintenance, and Troubleshooting Guide OL-0542-06 Chapter 7 Maintaining the Cisco Catalyst 5500 Multiswitch Router Replacing Hardware Components Checking the Installation Perform the following steps to verify that the new fan assembly is installed correc...