Cisco 5500 - Manual

Cisco 5500

Cisco 5500 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
Page: / 18

Table of Contents:

  • Page 2 – Supervisor Engine Module LEDs; Supervisor Engine III Front Panel; Supervisor Engine III and Uplink Module LED Descriptions; LED; Note
  • Page 3 – Ethernet Switching Module (10BaseT 24 Port) LEDs; Ethernet Switching Module (10BaseT 24 Port) LED Descriptions
  • Page 4 – Route Switch Module LEDs
  • Page 5 – Using the Command Line Interface to Check Status; show; Command Reference Manual; Replacing Hardware Components; Removing and Replacing the Power Supply, page 7-8; LED State
  • Page 6 – Avoiding Problems When Inserting and Removing Modules; Catalyst 5000 Series Module Installation Guide; Tools Required; To remove a supervisor engine, perform the following steps:
  • Page 7 – Place the removed module on an antistatic mat or antistatic foam.; show system; and; show module; commands to; Replacing the Supervisor Engine; Reattach network interface cables to the module ports.
  • Page 8 – Locating the Flash Memory Card Write-Protection Switch; Do not attempt to force the card past this point.; Removing and Replacing the Power Supply; Flash PC card
  • Page 9 – Removing an AC-Input Power Supply; Follow these steps to remove an AC-input power supply:; AC-Input Power Supply Front Panels; Disconnect the power cord from the power source.
  • Page 10 – Handling an AC-Input Power Supply; Pull the supply out of the bay and put it aside.; Installing an AC-Input Power Supply; “Removing an
  • Page 11 – Cisco Media Gateway Controller Hardware Installation Guide; Removing a DC-Input Power Supply; Warning
  • Page 12 – DC-Input Power Supply Front Panels; Loosen and remove the captive screws on the power supply (see; CO ground
  • Page 13 – Figure 7-11 Handling a DC Power Supply; Caution; Installing a DC-Input Power Supply; Follow these steps to install a DC-input power supply:
  • Page 15 – Figure 7-12 DC-Input Power Supply Connectors; command to display the power supply and system status.; Removing and Replacing the Chassis Fan Assembly; Removing the Fan Assembly
  • Page 16 – Installing the Fan Assembly; Perform the following steps to install the new fan assembly:; Figure 7-13 Cisco Catalyst 5500 Chassis Fan Assembly
  • Page 17 – Checking the Installation; “Obtaining Technical Assistance” section
Loading the manual

C H A P T E R

7-1

Cisco MGC Software Release 7 Operations, Maintenance, and Troubleshooting Guide

OL-0542-06

7

Maintaining the Cisco Catalyst 5500 Multiswitch
Router

This chapter contains recommended hardware maintenance procedures for the Cisco Catalyst 5500
Multiswitch Routers (MSRs), which provide an Ethernet backbone for connections between the
Cisco Signaling Link Terminals (SLTs), Cisco Media Gateway Controllers (MGCs), and Cisco Media
Gateways (MGWs). You can configure several virtual LANs (VLANs) on the Catalyst 5500s and the
route switch modules (RSMs) provide inter-VLAN routing when necessary. If your solution includes
two Catalyst 5500s, they are connected through an Inter-Switch Link (ISL) trunk, enabling them to share
VLAN data and provide ensured availability.

This chapter describes hardware maintenance; for information on upgrading and maintaining
Catalyst 5500 software, refer to the

Cisco Media Gateway Controller Software Release 7 Installation

and Configuration Guide

.

This chapter includes the following sections:

•

Checking Equipment Status, page 7-1

•

Replacing Hardware Components, page 7-5

Checking Equipment Status

Check the status of the Cisco Catalyst 5500, using the following methods:

•

Reading the Cisco Catalyst 5500 LEDs

•

Querying the status using the Catalyst command line interface (CLI)

•

Querying the system using CiscoWorks 2000 and Cisco WAN Manager (CWM)

Cisco Catalyst 5500 LEDs

LEDs of the Catalyst 5500 may vary, depending on which components are installed. The LEDs described
in this section are factory default.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Supervisor Engine Module LEDs; Supervisor Engine III Front Panel; Supervisor Engine III and Uplink Module LED Descriptions; LED; Note

7-2 Cisco MGC Software Release 7 Operations, Maintenance, and Troubleshooting Guide OL-0542-06 Chapter 7 Maintaining the Cisco Catalyst 5500 Multiswitch Router Checking Equipment Status Supervisor Engine Module LEDs The front panel of the supervisor engine III (product number WS X5530-E3) is shown i...

Page 3 - Ethernet Switching Module (10BaseT 24 Port) LEDs; Ethernet Switching Module (10BaseT 24 Port) LED Descriptions

7-3 Cisco MGC Software Release 7 Operations, Maintenance, and Troubleshooting Guide OL-0542-06 Chapter 7 Maintaining the Cisco Catalyst 5500 Multiswitch Router Checking Equipment Status Ethernet Switching Module (10BaseT 24 Port) LEDs Each switching module (Prod # WS-X5013) contains a STATUS LED. Wh...

Page 4 - Route Switch Module LEDs

7-4 Cisco MGC Software Release 7 Operations, Maintenance, and Troubleshooting Guide OL-0542-06 Chapter 7 Maintaining the Cisco Catalyst 5500 Multiswitch Router Checking Equipment Status 10/100 Mbps Fast Ethernet Switching Module (10/100BaseTX 12 Port) LEDs The faceplate of each 10/100 Mbps Fast Ethe...

Other Cisco Models

All Cisco Other