Chief PNR - Manuals - manualsarea.com

Page 2 - IMPORTANT WARNINGS AND CAUTIONS!; corresponding instructions.; CONTENTS

Model PNR™ Installation Instructions 2 IMPORTANT WARNINGS AND CAUTIONS! WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the c...

Page 3 - DIMENSIONAL DRAWING

Installation Instructions Model PNR™ 3 DIMENSIONAL DRAWING

Page 4 - Inspect The Unit Before Installing; INTERFACES; PARTS LIST; Table 2: PNR Interfaces

Model PNR™ Installation Instructions 4 Inspect The Unit Before Installing WARNING: Watch for pinch points. Do not put your fingers between movable parts. 1. Carefully inspect the PNR for shipping damage. If anydamage is apparent, call your carrier claims agentand do not continue with the installatio...

Page 5 - INSTALLATION; Figure 1; Install the Mount; Mounting the top bracket

Installation Instructions Model PNR™ 5 INSTALLATION WARNING: Improper installation can result in serious personal injury! WARNING: It is the responsibility of the installer to verify that the wall to which the PNR is anchored willsafely support five times the combined load of allattached components ...

Page 6 - Figure 2; Adjust Height on the PNR; Height adjustment range up to 1.08 inches.; Install Cover Plates and End Caps; The cover plates and end caps have pressure; Figure 4; Adjustment Nut

Model PNR™ Installation Instructions 6 Figure 2 Figure 3 Adjust Height on the PNR NOTE: Height adjustment range up to 1.08 inches. To adjust the PNR height: 1. Check PNR for the desired height. If needed, use theadjustment wrench (40) to adjust the PNR height. • Turn adjustment nut (see Figure 4) cl...

Page 7 - Mount the Display; Watch for pinch points. Do not put your; Figure 6; Holes are provided in the faceplate for use with a; Figure 7; CABLE MANAGEMENT; Make sure your cables do not run through

Installation Instructions Model PNR™ 7 Mount the Display 1. Make sure power is not supplied (turned off) to thedisplay before attempting to mount the display. 2. Following the instructions for mounting the PSBinterface bracket of your specific plasma displaypanel, install the mounting bracket on you...

Page 8 - Figure 8; ADJUSTMENTS; TENSION ADJUSTMENTS; Lateral Tilt Tension Adjustment; Overtightening lateral adjustment will; Rotational Tilt Tension Adjustment; Management Channel

Model PNR™ Installation Instructions 8 Figure 8 Figure 9 ADJUSTMENTS TENSION ADJUSTMENTS Vertical Tilt Tension Adjustment 1. With display mounted, check for desired vertical tilttension. 2. Adjust the Centris Select TM knob until desired vertical tilt tension is obtained. (See figure 10) Figure 10 3...

Page 9 - Swing Arm Adjustments; Adjusting the Swing Arms Off Center

Installation Instructions Model PNR™ 9 Figure 12 Swing Arm Adjustments The dual swing arms are shipped installed in the centerof the top and bottom mounting brackets, which is thestandard mounting configuration. The top and bottom mounting brackets have slottedholes, allowing for lateral adjustment ...

Page 10 - Swing Arm Tension Adjustment

Model PNR™ Installation Instructions 10 bottom) and secure using two bolts (one top and onebottom). 5. Install four bolts (two on the top and two on thebottom) to secure the swing arm assembly to the topand bottom mounting brackets (See figure 14). 6. Tighten the bolts. 7. Install the display on the...

Page 11 - Removing Display from Mount; Increase

Installation Instructions Model PNR™ 11 Figure 18 Removing Display from Mount 1. Remove bolt or padlock from faceplate (if used). NOTE: The pin may have been used as a more permanent locking device. If so, remove nut and pin and movefrom the lower holes to the upper holes. 2. Pull back on flag on up...