Chief MSP-DCCMD - Manuals - manualsarea.com

Page 2 - Installation Instructions; IMPORTANT WARNINGS AND CAUTIONS!; corresponding instructions.; DIMENSIONS; Front View

Model MSP-DCCMD Installation Instructions 2 IMPORTANT WARNINGS AND CAUTIONS! WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow ...

Page 3 - CONTENTS; Table 1: JWD Speifications

Installation Instructions Model MSP-DCCMD 3 CONTENTS TOOLS REQUIRED FOR INSTALLATION • Electric drill and bit set • Hex wrench set • Phillips screwdriver • Level NOTE: Other tools may be required depending on the mounting surface and method of installation. Inspect The Unit Before Installing WARNING...

Page 4 - PARTS

Model MSP-DCCMD Installation Instructions 4 PARTS Figure 1: JWD PARTS Centris Interface(see notes) Set Screw(see notes) 130 140 150 160 170 180 20 30 40 50 60 70 80 90 110120 190 100

Page 5 - Table 2 below provides a list of the JWD parts.

Installation Instructions Model MSP-DCCMD 5 PARTS (Continued) Table 2 below provides a list of the JWD parts. NOTES: ‡The M4 x 12mm screws (60) are used on the Centris interface for flush mount applications. *The M4 x 30mm screws (40) with spacers (100) are for recessed mount applications. **M4 x 20...

Page 6 - WALL BRACKET INSTALLATION; Secure Wall Bracket; back; Figure 2: Secure Wall Bracket; Wood; Set Screw

Model MSP-DCCMD Installation Instructions 6 WALL BRACKET INSTALLATION Secure Wall Bracket WARNING: It is the responsibility of the installer to verify that the surface to which the mount is anchored will safely support the combined load of all attached components and equipment. To install the mount:...

Page 7 - Flush Mount Centris Bracket to Display; Align the mounting holes on the Centris bracket with; Recess Mount Centris Bracket to Display; If your display uses a screw size other; Figure 4: Flush Mount Centris Bracket to Display; Display

Installation Instructions Model MSP-DCCMD 7 INSTALLATION (100mm x 100mm) Flush Mount Centris Bracket to Display 1. Install two M4 x 12mm screws (60) into the top mounting holes (not shown) on the display . 2. Align the mounting holes on the Centris bracket with the screws installed on the display. H...

Page 8 - Attach Interface Adapter to Display; Place display face down on a clean dry surface.; Attach Display to Centris Bracket; Hang the mount from the two screws started in Step 1.; Figure 6: Attach Interface Breacket to Display; Centris Bracket

Model MSP-DCCMD Installation Instructions 8 INSTALLATION (200mm x 100MM) Attach Interface Adapter to Display 1. Select six M4 screws (80) and six spacers (190) from parts bag. 2. Place display face down on a clean dry surface. 3. Install six M4 screws (80) into the six mounting holes on the interfac...

Page 9 - Figure 8: Attach 400mm x 200mm Interface Adapter

Installation Instructions Model MSP-DCCMD 9 INSTALLATION (400mm x 200MM and 550mm x 235MM) Attach 400mm x 200mm Interface Adapter NOTE: Used for 400mm x 200mm hole patterns. 1. Select six M6 screws (30) and six spacers (120) from parts bag. 2. Place display face down on a clean dry surface. 3. Insta...

Page 10 - CABLE MANAGEMENT; LATERAL TENSION ADJUSTMENT; Figure 11: Cable Management

Model MSP-DCCMD Installation Instructions 10 CABLE MANAGEMENT WARNING: Make sure your cables do not run through a pinch point. 1. Connect and secure power/audio/video cables, making sure to leave sufficient slack to allow for movement of the display. 2. Route power/audio/video cables under each arm,...