Chauvet DMX-690 - Manuals

Chauvet DMX-690 – Manual in PDF format online.

Manuals:

Manual

Manual Chauvet DMX-690

Summary

Page 3 - What is included; Contact Us; W o r l d W i d e

1. B EFORE Y OU B EGIN What is included ¾ 1 x Intimidator Spot 2.0 HTI™ ¾ 150W HTI Lamp ¾ Power Cord ¾ Warranty Card ¾ User Manual Unpacking Instructions Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received...

Page 4 - Safety Instructions

Safety Instructions Please read these instructions carefully, which includes important information about the installation, usage and maintenance of this product. • Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instructi...

Page 5 - NTRODUCTION; Features; DMX Channel Summary

2. I NTRODUCTION Features • 6 to 8-channel DMX-512 moving yoke • Pan: 540° / tilt: 270° • Variable strobe/shutter • Color wheel: 7 colors + white Rainbow color spin effect • Rotating gobo wheel: 7 interchangeable, rotating gobos + open 5 metal, 2 dichroic gobos Gobo wheel spin effect • Variable moto...

Page 6 - Product Overview; Rear of Base

Product Overview Control Panel DMX Output Connector Yoke Rear of Base AC Power Input & Fuse Holder Easy Controller Connector DMX Input Connector Base Head Focusing Lens Voltage Selector Switch Intimidator Spot 2.0 HTI Manual 6 2007-01-24/09:36

Page 7 - ETUP; Lamp; Figure A

3. S ETUP Lamp You will need to install a lamp prior to the initial operation of the fixture. A 150W HTI lamp is included. Warning! When replacing the lamp, please wait 15 minutes after powering down to allow the unit to cool down! Always disconnect from main power prior to lamp replacement. Do not ...

Page 8 - Lamp Alignment How-To; Fuse Replacement

Lamp Alignment How-To Often, after a new installation of a lamp, you will find that there is an uneven field of light or what is refered to as a hot spot. This is due to the most intense point of the lamp source not being positioned optimally within the reflector. Lamp alignment screws There are thr...

Page 9 - Replacing Gobos

Replacing Gobos 1) Remove the four screws indicated in figure A to remove the back of the head. Figure A Figure B Figure C Figure D 2) Remove the four screws indicated in figure B to remove the front of the head. 3) Orient the fixture so that it looks like the fixture in figure C. 4) Remove the glue...

Page 10 - Fixture Linking; Data Cabling; D M X D A T A C A B L E; C A B L E C O N N E C T O R S

Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determi...

Page 11 - - P I N T O 5 - P I N C O N V E R S I O N C H A R T; Setting up a DMX Serial Data Link

3 - P I N T O 5 - P I N C O N V E R S I O N C H A R T th a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter. CHAUVET Model No: DMX5M, or DMX5F. 3 P IN TO 5 P IN C duc 3 Pin Female (output) 5 Pin Male (Input) Note! If you use a controller wi The chart below details a proper c...

Page 12 - Mounting; O R I E N T A T I O N

Mounting O R I E N T A T I O N This fixture may be mounted in any position provided there is adequate room for ventilation. R I G G I N G Hanging Clamp It is important never to obstruct the fan or vents pathway. Mount the fixture using, a suitable “C” or “O” type clamp. Adjust the angle of the fixtu...

Page 13 - Navigating the Control Panel; DMX Signal Indicator

4. O PERATING I NSTRUCTIONS Navigating the Control Panel Access control panel functions using the four panel buttons located directly underneath the LCD Display. NOTE: The display will turn off after 30 seconds if no buttons are pushed. MODE /ESC Button Function <MODE/ESC> Used to access the m...

Page 14 - Menu Map

Menu Map Intimidator Spot 2.0 HTI Manual 14 2007-01-24/09:36

Page 15 - T O S E T T H E P A N T O I N V E R T I N G O R N O N - I N V E R T I N G :

Menu Functions User Configurations M ENU O PTION D ESCRIPTION DMX: The fixture will be controlled by a DMX signal coming from a DMX controller. The starting address must be selected, and can be set using the up and down buttons. Automatic – Master Unit: Sets the fixture to Master status for Master-S...

Page 16 - Service Functions; T O R E S E T T H E F I X T U R E :

T O C H A N G E T H E P A N R A N G E : 1) Press <MODE/ESC> until , , or is displayed.. 2) Use the <UP> and <DOWN> buttons to scroll through the three options. is 540°; is 360°; is 180° Note: These settings only apply if the fixture is in master/slave or stand-alone modes. These se...

Page 18 - DMX Mode

DMX Mode This mode allows the unit to be controlled by any universal DMX controller. If you are unfamiliar with DMX, please read the DMX Primer on page 21. 1) Press <MODE/ESC> until is displayed. 2) Use the <UP> and <DOWN> buttons to select the desired address and press the <ENT...

Page 20 - General Troubleshooting; Applies to

General Troubleshooting Applies to Symptom Solution(s) Lights Foggers & Snow Controllers Dimmers & Chaser Auto shut off Check fan thermal switch reset 9 Beam is very dim or not bright Clean optical system or replace lamp Check 220/110v switch for proper setting 9 Breaker/Fuse keeps blowing C...

Page 21 - Technical Support; PPENDIX; DMX Primer; General Maintenance

Technical Support Address: Service Dept. 3000 N 29th Ct, Hollywood, FL 33020 (U.S.A.) Support (Email): [email protected] Telephone: (954) 929-1115 - (Press 4) Fax: (954) 929-5560 - (Attention: Service) Website: http://www.chauvetlighting.com 5. A PPENDIX DMX Primer There are 512 channels in a...

Page 23 - Technical Specifications

Technical Specifications WEIGHT & DIMENSIONS Length.............................................................................................................................. 16 in (406 mm) Width ....................................................................................................