Breville BCG400SIL - Manuals

7 8 Functions GRINDER OVERVIEW Your Dose Control™ uses hardened stainless steel Conical Burrs and can grind whole bean coffee suitable for a range of brewing methods, from the finest setting for Espresso to the coarsest setting for French Press. You can grind directly into a Portafilter, Container o...

9 10 Breville Espresso Machine Portafilter Size Dose Height BES900/920XL 58mm 2 BES870XL 54mm 2.5 BES840XL 54mm 2.5 BES810 54mm 2.5 800ESXL 50mm 3 BES250XL 50mm 3 ESP8XL 50mm 3 Step 5: After tamping the coffee Insert the Razor™ into the filter basket until it rests on the rim of the basket. The blad...

11 Care & Cleaning CARE, CLEANING & STORAGE 1. Empty beans from the hopper and grind out any excess beans. 2. Unplug power cord from power outlet before cleaning. 3. Remove Hopper. Refer to page 7 to remove hopper. 4. Wash the hopper lid and bean hopper in warm soapy water, rinse and dry tho...

13 14 Troubleshooting PROBLEM POSSIBLE CAUSE WHAT TO DO Grinder does not start after pressing START/ CANCEL button. • Grinder not plugged in • Bean hopper not installed correctly. • Grinder has overheated. • Plug power cord into power outlet • Lock bean hopper into position. refer to the Bean Hopper...

Step 4 — Remove hopper, upper burrs, and lower burrs Remove the hopper and upper burrs.  Use a 10mm socket to remove the nut for the lower burrs.  The nut for the lower burrs is reverse threaded. Rotate clockwise to loosen.  Turn the grind-adjustment knob to the finest setting.  Remember what or...

Step 5 — Remove the base Unwrap the power cord and remove the 4 screws from the base.  Remove the four rubber pads  Slide the power cord through the hole in the base while lifting the base away from the grinder.  BCG800XL Grinder Jamming due to Worn… Draft: 2020-12-02 Guide ID: 62905 - This docum...

Step 6 — Remove 4 screws holding the top on Use the long Phillips #2 driver to remove the 4 screws holding the top in place.  Flip the grinder over and slowly lift away the top.  The top is still attached to a wire so the lid will hang off to the side.  BCG800XL Grinder Jamming due to Worn… Draft...

Step 7 — Remove the front display Remove the two screws from the top of the display.  Lift the display up and out of the frame.  BCG800XL Grinder Jamming due to Worn… Draft: 2020-12-02 Guide ID: 62905 - This document was generated on 2020-12-04 12:47:34 PM (MST). © iFixit — CC BY-NC-SA www.iFixit....

Step 8 — Gear / Burr holder Assembly Removal Be sure the grind knob is turned to the finest setting.  It's critical that the alignment be preserved when removing the gear assembly. The small gear inthe picture is an encoder. Its purpose is to track the position of the grind adjustment level so itca...

Step 11 — Installing the 3D Printed Impeller Replacement It is important for the 3D printed part to fit properly. Tolerances of the design error on the tight side.  Check that the burr drive pegs fit the holes of the conical burrs. If it’s too tight, apply a smallamount of sanding to the impeller a...

Step 12 — Checking Fit and Burr Elevation Before reassembly, check that the conical lower burr and impeller fit well onto the driveshaft withboth steel washers underneath. Make sure all parts in the cutaway diagram are accounted for.  The lip on the drive shaft should be within about 0.5mm of the t...

Step 13 — Reinstall the Gear / Burr holder assembly With the following pieces aligned carefully set the gear assembly into place:  Avoid rotating these pieces to maintain alignment.  As you set the assembly into place, make sure the two stop-screws are on the left side of theblack plastic stop.  ...

Step 14 — Optional Modification for Better Grind Adjustment Range Advanced Modding Tip: If you wantgreater grind-control range, you canback out the two screws in the biggear in the photo. You will then beable to adjust the grind muchbeyond the normal range. Caveats:Go too fine and the grounds become...

Step 15 — Reinstall the Display and the Conical Lower Burr Place the display back into theframe and screw in the two screwsthat hold it in place.  Put the conical burr in place makingsure it sets on the drive pegs of thenew impeller properly.  Place the washers on whilemaintaining their original o...

Step 16 — Put the top back on and screw it back in Put the plastic top back on.  Flip the grinder over and use the long Phillips #2 screwdriver to reinstall the 4 screws that hold thetop in place.  If the screwdriver is not already magnetized, it'll be worth rubbing a magnet on it to do so prior t...

Step 17 — Reinstall the bottom Put the four rubber feet back inplace.  Screw back in the four base screws.  Re-wrap the cord.  BCG800XL Grinder Jamming due to Worn… Draft: 2020-12-02 Guide ID: 62905 - This document was generated on 2020-12-04 12:47:34 PM (MST). © iFixit — CC BY-NC-SA www.iFixit.c...

Step 18 — Reinstall upper burrs and hopper Put the upper burr back on and reinstall the hopper (without coffee beans yet).  Run the (empty) grinder briefly to make sure it all sounds OK. Try both coarse and fine grindsettings.  If all sounds well, add some coffee to the hopper. Dial in the grind a...

Step 20 — Troubleshooting #2 - Burr Clearance TOO CLOSE (ie: grinding too fine): If the burrs are too close, or even touching (but centered), thenut on the lower burr may not be tight enough. With the ratchet and 10mm socket, give it a quickcounter-clockwise jerk. If that fails, recheck your fit-up ...

The drive gear on the right has apotential source found by a userbelow (Thanks Dave Gordon!): http://www.forumappliances.com/breville-... This is not yet verified to work, but the price is reasonable, soif you try it out and it works, postbelow so we can know!  BCG800XL Grinder Jamming due to Worn…...

7 8 Functions GRINDER OVERVIEW Your Dose Control™ uses hardened stainless steel Conical Burrs and can grind whole bean coffee suitable for a range of brewing methods, from the finest setting for Espresso to the coarsest setting for French Press. You can grind directly into a Portafilter, Container o...

9 10 Breville Espresso Machine Portafilter Size Dose Height BES900/920XL 58mm 2 BES870XL 54mm 2.5 BES840XL 54mm 2.5 BES810 54mm 2.5 800ESXL 50mm 3 BES250XL 50mm 3 ESP8XL 50mm 3 Step 5: After tamping the coffee Insert the Razor™ into the filter basket until it rests on the rim of the basket. The blad...

11 Care & Cleaning CARE, CLEANING & STORAGE 1. Empty beans from the hopper and grind out any excess beans. 2. Unplug power cord from power outlet before cleaning. 3. Remove Hopper. Refer to page 7 to remove hopper. 4. Wash the hopper lid and bean hopper in warm soapy water, rinse and dry tho...

13 14 Troubleshooting PROBLEM POSSIBLE CAUSE WHAT TO DO Grinder does not start after pressing START/ CANCEL button. • Grinder not plugged in • Bean hopper not installed correctly. • Grinder has overheated. • Plug power cord into power outlet • Lock bean hopper into position. refer to the Bean Hopper...

15 16 Table des matières 15 Breville vous recommande la sécurité avant tout 19 Composants 21 Fonctions 25 Entretien & Nettoyage 26 Trucs de préparation du café 27 Guide de dépannage IMPORTANTES MESURES DE SÉCURITÉ Chez Breville, la sécurité occupe une place de choix. Nous concevons et fabriquons...

17 18 INSTRUCTIONS SUR LE COUR CORDON Votre appareil Breville est muni d'un court cordon d'alimentation qui réduit le risque de blessure ou dommages matériels résultant du fait de tirer, trébucher ou s'enchevêtrer dans un cordon plus long. Si vous utilisez une rallonge: (1) la puissance nominale ind...

19 20 Composants A. Couvercle de la trémie à grains B. Trémie à trains Trémie d'une capacité de 340 g, amovible pour faciliter le nettoyage. C. Meules coniques en acier inoxydable trempé Maximisent l'uniformité de la taille des particules, pour plus de saveur. D. Collier d'ajustement de la mouture 6...

21 22 Fonctions APERÇU DU MOULIN Votre Dose Control MC utilise des meules coniques en acier inoxydable trempé qui peuvent moudre des grains de café entiers convenant à une variété de méthodes d'infusion, allant du réglage le plus fin pour l’espresso au plus grossier pour la cafetière à piston. Vous ...

23 24 50mm 'DÉCLIC' PRESSER SUR LES DEUX BOUTS Ajustez l'outil Razor MC selon le tableau ci-après en fonction de votre machine à espresso Breville. Cela vous donnera une idée de la hauteur de votre dose. Machine à espresso Breville Format du porte-filtre Hauteur de la dose BES900/920XL 58 mm 2 BES87...

25 Entretien et Nettoyage ENTRETIEN, NETTOYAGE & RANGEMENT 1. Videz complètement la trémie à grains et broyez l'excédent, si nécessaire. 2. Débranchez l'appareil avant de le nettoyer. 3. Retirez la trémie. Consultez les instructions pour retirer la trémie en page 21. 4. Lavez la trémie et son co...

27 28 Guide de dépannage PROBLÈME CAUSE POSSIBLE QUE FAIRE Le moulin ne démarre pas après avoir pressé sur le bouton MARCHE|ANNULER. • Le moulin n'est pas branché • La trémie n'est pas installée correctement. • Le moulin a surchauffé. • Branchez le cordon dans la prise électrique. • Fixez en place l...