Bosch WAP28380AU - Manuals

Safety instructions en 5 ( Safety instructions Safety instructions Electrical safety : Warning Danger of death! There is a risk of electric shock if you touch live components. ■ Never touch or hold the mains plug with wet hands. ■ Only pull out the mains cable by the plug and never by the cable, as ...

en Safety instructions 6 : Warning Danger of death! Children may lock themselves in appliances, putting their lives at risk. For appliances that have reached the end of their service life: ■ Disconnect the mains plug. ■ Cut through the mains cable and remove it, along with plug. ■ Destroy the lock o...

Environmental protection en 7 7 Environmental protection Environmental protection Packaging/used appliance Do’s ■ Hand over the old/discarded electronic equipment only to authorized collection centers for disposal ■ Consult the authorized service center as to whether the Electronic Equipment can be ...

en Getting to know the appliance 8 * Getting to know the appliance Getting to know the appliance Washing machine 6 7 # ( Detergent dispenser 0 Control panel 8 Door 9S Open the door 9T Close the door @ Service flap

Getting to know the appliance en 9 Control panel You can find possible programme default settings and additional programme settings in the overview; these differ depending on the model. ( Programme default settings can be changed. Overview of all programme default settings ~ Page 13 0 additional pro...

en Getting to know the appliance 10 Display panel In the table you can find possible settings and information in the display panel; these differ depending on the model. Settings for the selected programme — - 90* Temperature in °C Temperature - - - -, 0 - 1400* Spin speed in rpm (revolutions per min...

Laundry en 11 Z Laundry Laundry Prepare the laundry Caution! Damage to the appliance/fabrics Foreign objects (e.g. coins, paper-clips, needles, nails) may damage the laundry or components in the washing machine. Therefore, note the following tips when preparing your laundry: ■ Empty pockets. ■ Look ...

en Detergent 12 C Detergent Detergent Correct selection of detergent The care label is crucial to ensure correct detergent selection, temperature and laundry treatment. ■ Standard detergent with optical brighteners suitable for heat-resistant white washing made from linen or cotton Programme: i Cott...

Programme default settings en 13 0 Programme default settings Programme default settings Note: You can find possible programme default settings in the overview; these differ depending on the model. The programme default settings for all programmes are preset at the factory and are displayed in the d...

en Additional programme settings 14 \ Additional programme settings Additional programme settings Note: You can find possible additional programme settings in the overview; these differ depending on the model. SpeedPerfect/EcoPerfect ( G F ) Button with two possible settings for adapting the selecte...

Operating the appliance en 15 1 Operating the appliance Operating the appliance Note: Install and connect washing machine properly. Before the 1st wash ~ Page 31 Preparing the washing machine Notes ■ Never switch on a damaged washing machine! ■ Inform customer service! 1. Connect the mains plug. 2. ...

en Operating the appliance 16 Notes ■ Mix items of laundry of varying sizes. Laundry items of different sizes distribute themselves better during the spin cycle. Individual items of laundry may lead to imbalances. ■ Observe the specified maximum load. Overfilling has a negative impact on the washing...

Operating the appliance en 17 1. Pull out the detergent drawer as far as possible. 2. Add detergent and/or care products. 3. Close the detergent drawer. Measuring aid* for liquid detergent *Depending on the model Position the measuring aid for measuring the correct amount of liquid detergent: 1. Pul...

Setting the signal en 19 M Setting the signal Setting the signal You can change the following settings: ■ The volume for the information signals (e.g. at the end of the program) and/or ■ The volume of the audible button signals. You will need to activate the setting mode in order to change these set...

Cleaning and maintenance en 21 Allow the water to cool down. 1. Turn off the water tap so that no more water can flow in and has to be drained via the drain pump. 2. Switch off the appliance. Disconnect the mains plug. 3. Open and remove the service flap. 4. Take the drain hose out of the retainer. ...

en Faults and what to do about them. 22 Filter in the water supply blocked First, reduce the water pressure in the supply hose: 1. Turn off the tap. 2. Select any program (except ' Rinse/Freshen up//Rinse// 0 Spin/Drain [ ). 3. Press the A button.Allow the program to run for approximately 40 seconds...

Faults and what to do about them. en 23 Information on the display panel Faults and what to do about them. Display Cause/Remedy è ■ Flashes fast + signal : The door was opened and the water level is too high. Close the door, continue the programme with A button or select 0 Spin/Drain [ programme. ■ ...

After-sales service en 25 4 After-sales service After-sales service If you cannot correct the fault yourself, (see section, Faults and what to do about them ~ Page 22 ), please contact our after-sales service ~ Cover page We will always find an appropriate solution in order to avoid unnecessary visi...

en Positioning and connecting 26 5 Positioning and connecting Positioning and connecting Included with the appliance Note: Check the machine for transport damage. Never use a damaged machine. If you have any complaints, contact the dealer from whom you purchased the appliance or our Customer Service...

Positioning and connecting en 29 Optimum water pressure in the supply networkAt least 100 kPa (1 bar) Maximum 1000 kPa (10 bar) When the tap is open, the water flow is at least 8 l/min.If the water pressure is higher than this, a pressure-reducing valve must be installed. Connection 1. Connect the w...

en Positioning and connecting 30 ■ Drainage into a siphon The connection point must be secured using a hose clamp with a diameter of 24-40 mm (available from specialist dealers). ■ Outlet into a plastic pipe with rubber bushing or into a drainage pit Levelling Level the appliance using a spirit leve...

Positioning and connecting en 31 Before washing for the first time The washing machine was thoroughly tested before leaving the factory. To remove any water that may be left over from the test, run the first wash cycle without any laundry. Notes ■ The washing machine must be correctly installed and ...

Robert Bosch Hausgeräte GmbH Carl-Wery-Straße 34 81739 München, GERMANY *9001051717* 9001051717 (9503) You can find the contact information for all countries in the attached after-sales service directory.