Page 2 - Your new washing machine; Display rules
2 Your new washing machine You have chosen a Bosch washing machine. Please take a few minutes to read and become familiar with the advantages of your washing machine. To meet the high quality demands required by Bosch, every washing machine that leaves our factory is carefully checked to ensure that...
Page 3 - Contents; Getting to know the appliance . 8
en 3 Contents enInstruction Manual and Installation Instructions 8 Intended use. . . . . . . . . . . . . . . . .4 ( Safety instructions . . . . . . . . . . .5 Electrical safety. . . . . . . . . . . . . . . . . . 5 Risk of injury . . . . . . . . . . . . . . . . . . . . 5 Safety for children . . . . ....
Page 4 - are
en Intended use 4 Installation on a base or a wooden joist floor . . . . . . . . . . . . . . . . . . . . . 27 Installation on a platform with drawer . . . . . . . . . . . . . . . . . . . . . . . 27 Installing the appliance in a kitchenette . . . . . . . . . . . . . . . . . . . . 27 Removing the tran...
Page 5 - Safety instructions; Electrical safety
Safety instructions en 5 ( Safety instructions Safety instructions Electrical safety : Warning Danger of death! There is a risk of electric shock if you touch live components. ■ Never touch or hold the mains plug with wet hands. ■ Only pull out the mains cable by the plug and never by the cable, as ...
Page 6 - Warning
en Safety instructions 6 : Warning Danger of death! Children may lock themselves in appliances, putting their lives at risk. For appliances that have reached the end of their service life: ■ Disconnect the mains plug. ■ Cut through the mains cable and remove it, along with plug. ■ Destroy the lock o...
Page 7 - Packaging/used appliance; Do’s; Tips on economical use; Information about the energy
Environmental protection en 7 7 Environmental protection Environmental protection Packaging/used appliance Do’s ■ Hand over the old/discarded electronic equipment only to authorized collection centers for disposal ■ Consult the authorized service center as to whether the Electronic Equipment can be ...
Page 8 - Washing machine
en Getting to know the appliance 8 * Getting to know the appliance Getting to know the appliance Washing machine 6 7 # ( Detergent dispenser 0 Control panel 8 Door 9S Open the door 9T Close the door @ Service flap
Page 9 - Control panel; Programme default settings
Getting to know the appliance en 9 Control panel You can find possible programme default settings and additional programme settings in the overview; these differ depending on the model. ( Programme default settings can be changed. Overview of all programme default settings ~ Page 13 0 additional pro...
Page 10 - Display panel; differ depending on the model.; Settings for the selected programme; * Depending on the model
en Getting to know the appliance 10 Display panel In the table you can find possible settings and information in the display panel; these differ depending on the model. Settings for the selected programme — - 90* Temperature in °C Temperature - - - -, 0 - 1400* Spin speed in rpm (revolutions per min...
Page 11 - Laundry; Prepare the laundry; Damage to the appliance/fabrics; Sorting laundry
Laundry en 11 Z Laundry Laundry Prepare the laundry Caution! Damage to the appliance/fabrics Foreign objects (e.g. coins, paper-clips, needles, nails) may damage the laundry or components in the washing machine. Therefore, note the following tips when preparing your laundry: ■ Empty pockets. ■ Look ...
Page 12 - Correct selection of detergent; Saving
en Detergent 12 C Detergent Detergent Correct selection of detergent The care label is crucial to ensure correct detergent selection, temperature and laundry treatment. ■ Standard detergent with optical brighteners suitable for heat-resistant white washing made from linen or cotton Programme: i Cott...
Page 13 - Temperature
Programme default settings en 13 0 Programme default settings Programme default settings Note: You can find possible programme default settings in the overview; these differ depending on the model. The programme default settings for all programmes are preset at the factory and are displayed in the d...
Page 14 - SpeedPerfect/EcoPerfect; SpeedPerfect; Soak; Notes; Easy Iron
en Additional programme settings 14 \ Additional programme settings Additional programme settings Note: You can find possible additional programme settings in the overview; these differ depending on the model. SpeedPerfect/EcoPerfect ( G F ) Button with two possible settings for adapting the selecte...
Page 15 - Operating the; Install; Never switch on a damaged
Operating the appliance en 15 1 Operating the appliance Operating the appliance Note: Install and connect washing machine properly. Before the 1st wash ~ Page 31 Preparing the washing machine Notes ■ Never switch on a damaged washing machine! ■ Inform customer service! 1. Connect the mains plug. 2. ...
Page 16 - Measure and add detergent; Damage to the appliance
en Operating the appliance 16 Notes ■ Mix items of laundry of varying sizes. Laundry items of different sizes distribute themselves better during the spin cycle. Individual items of laundry may lead to imbalances. ■ Observe the specified maximum load. Overfilling has a negative impact on the washing...
Page 19 - Activate setting mode:; Sensors; Unbalanced load detection
Setting the signal en 19 M Setting the signal Setting the signal You can change the following settings: ■ The volume for the information signals (e.g. at the end of the program) and/or ■ The volume of the audible button signals. You will need to activate the setting mode in order to change these set...
Page 21 - II; The drain hose at the siphon
Cleaning and maintenance en 21 Allow the water to cool down. 1. Turn off the water tap so that no more water can flow in and has to be drained via the drain pump. 2. Switch off the appliance. Disconnect the mains plug. 3. Open and remove the service flap. 4. Take the drain hose out of the retainer. ...
Page 22 - Faults and what to do; Emergency release
en Faults and what to do about them. 22 Filter in the water supply blocked First, reduce the water pressure in the supply hose: 1. Turn off the tap. 2. Select any program (except ' Rinse/Freshen up//Rinse// 0 Spin/Drain [ ). 3. Press the A button.Allow the program to run for approximately 40 seconds...
Page 23 - Information on the display panel; Display; Faults; Is the
Faults and what to do about them. en 23 Information on the display panel Faults and what to do about them. Display Cause/Remedy è ■ Flashes fast + signal : The door was opened and the water level is too high. Close the door, continue the programme with A button or select 0 Spin/ Drain [ programme. ■...
Page 25 - Trust the expertise of the; Product number
After-sales service en 25 4 After-sales service After-sales service If you cannot correct the fault yourself, (see section, Faults and what to do about them ~ Page 22 ), please contact our after-sales service.We will always find an appropriate solution in order to avoid unnecessary visits by enginee...
Page 26 - Included with the appliance; In addition
en Positioning and connecting 26 5 Positioning and connecting Positioning and connecting Included with the appliance Note: Check the machine for transport damage. Never use a damaged machine. If you have any complaints, contact the dealer from whom you purchased the appliance or our Customer Service...
Page 29 - Water outlet; Water damage
Positioning and connecting en 29 Optimum water pressure in the supply networkAt least 100 kPa (1 bar) Maximum 1000 kPa (10 bar) When the tap is open, the water flow is at least 8 l/min.If the water pressure is higher than this, a pressure-reducing valve must be installed. Connection 1. Connect the w...
Page 30 - Levelling
en Positioning and connecting 30 ■ Drainage into a siphon The connection point must be secured using a hose clamp with a diameter of 24-40 mm (available from specialist dealers). ■ Outlet into a plastic pipe with rubber bushing or into a drainage pit Levelling Level the appliance using a spirit leve...
Page 31 - Transportation; Installing the transport locks:
Positioning and connecting en 31 Before washing for the first time The washing machine was thoroughly tested before leaving the factory. To remove any water that may be left over from the test, run the first wash cycle without any laundry. Notes ■ The washing machine must be correctly installed and ...
Page 32 - Robert Bosch Hausgeräte GmbH; Advice and repair order in the event of faults; IE
Robert Bosch Hausgeräte GmbH Carl-Wery-Straße 34 81739 München, GERMANY *9001051717* 9001051717 (9802) You can find the contact information for all countries in the attached after-sales service directory. 7 Advice and repair order in the event of faults GB 0344 892 8979 (Calls charged at local or mo...
