Billion 8500 - Manuals

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 1: Introduction Simple Network Management Protocol (SNMP) It is an easy way to remotely manage the router via SNMP. Web based GUI Supports web based GUI for configuration and management. It is user-friendly and comes with on-line h...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 2: Installing the Router Important note for using the BIPAC-8500 / 8520 SHDSL Router DO NOT use the BIPAC-8500/8520 in high humidity or hightemperatures. DO NOT use the same power source for the BIPAC-8500/8520as other equipment. D...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router The Front LEDs of BIPAC-8500 6 2 4 1 3 LED Meaning 1 LINE Lit when successfully connected to SHDSL line and it is synchronized. 2 LAN Port 1X — 4X (RJ-45 connector) Lit when connected to an Ethernet device. Green for 100Mbps; Orange for 10...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 2: Installing the Router The Front LEDs of BIPAC-8520 3 5 2 1 4 LED Meaning 1 2 LINE 1 & 2 Lit when successfully connected to SHDSL line and it is synchronized. 3 LAN Port 1X — 4X (RJ-45 connector) Lit when connected to an Ethe...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 2: Installing the Router The Rear Ports 1 2 3 4 5 *6 ＊ Only the BIPAC-8520 has two Line jack ports. BIPAC-8500 has one. Port Meaning 1 Power Switch Power ON/OFF switch 2 PWR Connect the supplied power adapter to this jack. 3 RESET ...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 2: Installing the Router Cabling One of the most common causes of problems is bad cabling or SHDSL line(s). Make sure that all connected devices are turned on. On the front of the product is a bank of LEDs. Verify that the LAN Link...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 3: Basic Installation 10 Chapter 3: Basic Installation The router can be configured with your web browser. A web browser is included as a standard application in the following operating systems: Linux, Mac OS, Windows 98/NT/2000/XP...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 3: Basic Installation 11 Configuring PCs in Windows For Windows XP 1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click Network Connections . 2. Double-click Local Area Connection . (See Figure 3.1) ...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 3: Basic Installation 15 Factory Default Settings Before configuring your, you need to know the following default settings. Web Interface: Username: admin Password: admin LAN Device IP Settings: IP Address: 192.168.1.254 Subnet Mas...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 3: Basic Installation 16 Information from your ISP Before configuring this device, you have to check with your ISP (Internet Service Provider) what kind of service is provided such as PPPoE, PPPoA, RFC1483, or IPoA. Gather the info...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 3: Basic Installation 17 Configuring with your Web Browser Open your web browser, enter the IP address of your router, which by default is 192.168.1.254 , and click “ Go ”, a user name and password window prompt will appear. The de...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Chapter 4: Configuration At the configuration homepage, the left navigation pane where bookmarks are provided links you directly to the desired setup page, including: Status (ARP Table, Routing Table, DHCP Table, P...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Status ARP Table This section displays the router’s ARP (Address Resolution Protocol) Table, which shows the mapping of Internet (IP) addresses to Ethernet (MAC) addresses. This is useful as a quick way of determin...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Routing Table Routing Table: Valid: It indicates a successful routing status. Destination: The IP address of the destination network. Netmask: The destination netmask address. Gateway/Interface: The IP address of t...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration DHCP Table Leased: The DHCP assigned IP addresses information. IP Address: A list of IP addresses of devices on your LAN (Local Area Network). Expired: The expired IP addresses information. Permanent: The fixed hos...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration PPTP Status This shows details of your configured PPTP VPN Connections. Name: The name you assigned to the particular PPTP connection in your VPN configuration. Type: The type of connection (dial-in/dial-out). Enab...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration IPSec Status This shows details of your configured IPSec VPN Connections. Name: The name you assigned to the particular VPN entry. Active: Whether the VPN Connection is currently Active. Connection State: Whether t...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration L2TP Status This shows details of your configured L2TP VPN Connections. Name: The name you assigned to the particular L2TP connection in your VPN configuration. Type: The type of connection (dial-in/dial-out). Enab...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Event Log This page displays the router’s Event Log entries. Major events are logged to this window, such as when the router’s SHDSL connection is disconnected, as well as Firewall events when you have enabled Intr...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration NAT Sessions This section lists all current NAT sessions between interface of types external (WAN) and internal (LAN). UPnP Portmap The section lists all port-mapping established using UPnP (Universal Plug and Play...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Quick Start For detailed instructions on configuring your WAN settings, please see the WAN section of this manual. Usually, the only details you will need for the Quick Start wizard to get you online are your login...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Select the desired option from the list and click Apply to return to the Quick Start interface to continue configuring your ISP connection. Please note that the contents of this list will vary, depending on what is...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Configuration When you click this item, you get following sub-items to configure the SHDSL router. LAN, WAN, System, Firewall, VPN, QoS, Virtual Server and Advanced These functions are described below in the follow...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Port Setting This section allows you to configure the settings for the router’s Ethernet ports to solve some of the compatibility problems that may be encountered while connecting to the Internet, as well allowing ...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration DHCP Server You can disable or enable the DHCP (Dynamic Host Configuration Protocol) server or enable the router’s DHCP relay functions. The DHCP protocol allows your router to dynamically assign IP addresses to PC...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration If you check DHCP Relay Agent and click Next , then you will have to enter the IP address of the DHCP server which will assign an IP address back to the DHCP client in the LAN. Use this function only if advised to ...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration WAN (Wide Area Network) WAN refers to your Wide Area Network connection, i.e. your router’s connection to your ISP and the Internet. There are two items within the WAN section: ISP , DNS and SHDSL . ISP The factory...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration RFC 1483 Routed Connections Description: Your description of this connection. VPI and VCI: Enter the information provided by your ISP. ATM Class: The Quality of Service for ATM layer. NAT: The NAT (Network Address ...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration DHCP client function, and specify the IP address manually. The setting of this item is specified by your ISP. Authentication Protocol: Default is Chap(Auto ). Your ISP will advise you whether to use Chap or Pap. Co...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Give DNSto Relay: Controls whether the PPP Internet Protocol Control Protocol (IPCP) can request the DNS server IP address for a remote PPP peer. Once IPCP has discovered the DNS server IP address, it automatically...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration RFC 1483 Bridged Connections VPI and VCI: Enter the information provided by your ISP. ATM Class: The Quality of Service for ATM layer. Encapsulation method: Select the encapsulation format, this is provided by your...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration PPPoA Routed Connections Description: User-definable name for the connection. VPI/VCI: Enter the information provided by your ISP. ATM Class: The Quality of Service for ATM layer. NAT: The NAT (Network Address Tran...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration IPoA Routed Connections Description: User-definable name for the connection. VPI/VCI: Enter the information provided by your ISP. ATM Class: The Quality of Service for ATM layer. NAT: The NAT (Network Address Trans...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration DNS A Domain Name System (DNS) contains a mapping table for domain name and IP addresses. On the Internet, every host has a unique and user-friendly name (domain name) such as www.billion.com and an IP address. An ...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration SHDSL Mode: The default is CPE (Customer Premises Equipment) mode. If you want to do back to back connection with another BIPAC-8500, you must set to CO (Central Office) mode on another unit. Annex Type: SHDSL stan...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration System There are six items within the System section: Time Zone, Remote Access, Firmware Upgrade, Backup/Restore, Restart and User Management. Time Zone The router does not have a real time clock on board; instead,...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Remote Access To temporarily permit remote administration of the router (i.e. from outside your LAN), select a time period the router will permit remote access for and click Enable. You may change other configurati...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Firmware Upgrade Your router’s “firmware” is the software that allows it to operate and provides all its functionality. Think of your router as a dedicated computer, and the firmware as the software it runs. Over t...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Backup/Restore These functions allow you to save and backup your router’s current settings to a file on your PC, or to restore a previously saved backup. This is useful if you wish to experiment with different sett...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Restart Router Click Restart with option Current Settings to reboot your router (and restore your last saved configuration). If you wish to restart the router using the factory default settings (for example, after ...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration User Management In order to prevent unauthorized access to your router’s configuration interface, it requires all users to login with a password. You can set up multiple user accounts, each with their own password....

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Firewall and Access Control Your router includes a full SPI (Stateful Packet Inspection) firewall for controlling Internet access from your LAN, as well as helping to prevent attacks from hackers. In addition to th...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration URL Filter : To block PCs on your local network from unwanted websites. You can find six items under the Firewall section: General Settings, Packet Filter, Intrusion Detection, MAC Address Filter, URL Filter and Fi...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration General Settings You can choose not to enable Firewall, to add all filter rules by yourself, or enable the Firewall using preset filter rules and modify the port filter rules as required. The Packet Filter is divid...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Packet Filter 54

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Port Filters The pre-defined port filter rules for High, Medium and Low security levels are listed. See Table 1. Table 1: Pre-defined Port Filter Port Number Firewall - High Firewall - Medium Firewall - Low Applica...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Address Filters Address Filters are used to block traffic to/from particular IP addresses. They can be used to block IP addresses either on the Internet or on your local network. There are no pre-defined address fi...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Example: Configuring your firewall to allow for a publicly accessible web server on your LAN The pre-defined port filter rule for HTTP (TCP port 80) is the same no matter whether the firewall is set to a high, medi...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration 2. Click Port Filters . You will then be presented with the pre-defined port filter rules screen (in this case for the low security level), shown below: Click Delete 3. Click Delete to delete the existing HTTP rule...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration 6. The new port filter rule for HTTP is shown below: 7. Configure your Virtual Server (“port forwarding”) settings so that incoming HTTP requests on port 80 will be forwarded to the PC running your web server: To e...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Intrusion Detection The router’s Intrusion Detection System (IDS) is used to detect hacker attacks and intrusion attempts from the Internet. If the IDS function of the firewall is enabled, inbound packets are filte...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration MAC Address Filter A MAC (Media Access Control) address is the unique network hardware identifier for each PC on your network’s interface (i.e. its Network Interface Card or Ethernet card). Using your router’s MAC ...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration URL Filter URL (Uniform Resource Locator – e.g. an address in the form of http://www.billion.com or http://www.example.com ) filter rules allow you to prevent users on your network from accessing particular website...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Domains Filtering: This function checks the domain name in URLs accessed against your list of domains to block or allow. If it is matched, the URL request will be sent (Trusted) or dropped (Forbidden). The checking...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Firewall Log Firewall Log display log information of any unexpected action with your firewall settings. Check the Enable box to activate the logs. Log information can be seen in the Status – Event Log after enablin...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration VPN (Virtual Private Networks) Your router support three main types of VPN (Virtual Private Network), PPTP , IPSec and L2TP , and these are the two major section choices from the menu on the left. PPTP There are tw...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Remote Access PPTP Connection Connection Name: This allows you to identify this particular connection, e.g. “Connection to office”. Type: Check Dial Out if you want your router to operate as a client (connecting to...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Mode: You may select Stateful or Stateless mode. The key will be changed every 256 packets when you select Stateful mode. If you select Stateless mode, the key will be changed in each packet. Idle Time : Auto-disco...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration LAN to LAN PPTP Connection Connection Name: A user-define description of the connection. Type: Check Dial Out if you want your router to operate as a client (connecting to a remote VPN server, e.g. your office serv...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration IPSec Click Create to configure a new IPSec VPN connection. 71

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Configure a new VPN Connection Connection Name: A user-defined name for the connection (e.g. “connection to office”). Local: Local Network: Set the IP address, subnet or address range of the local network. Single A...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Advanced Option Click Advanced Option to change the following settings: IKE Mode: Select IKE mode to Main mode or Aggressive mode. Local ID: Type: Specify local ID type. Content: Input ID’s information, like domain...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration L2TP There are two types of L2TP VPN supported, Remote Access and LAN-to-LAN (please refer below for more information.). Click Create to configure a new VPN connection. 75

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Remote Access L2TP Connection Connection Name: This allows you to identify this particular connection, e.g. “Connection to office”. Type: Check Dial Out if you want your router to operate as a client (connecting to...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration IPSec: Enable for enhancing your LT2P VPN security. Authentication: Authentication establishes the integrity of the datagram and ensures it is not tampered with in transmit. There are three options, Message Digest ...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration LAN to LAN L2TP Connection Connection Name: A user-define description of the connection. Type: Check Dial Out if you want your router to operate as a client (connecting to a remote VPN server, e.g. your office serv...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Example: Configuring a Remote Access PPTP VPN Dial-in Connection A remote worker establishes a PPTP VPN connection with the head office using Microsoft's VPN Adapter (included with Windows 2000/ME, etc.). The route...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Example: Configuring a Remote Access PPTP VPN Dial-out Connection A company’s office establishes a PPTP VPN connection with a file server located at a separate location. The router is installed in the office, conne...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Example: Configuring a LAN-to-LAN PPTP VPN Connection The branch office establishes a PPTP VPN tunnel with head office to connect two private networks over the Internet.. The routers are installed in the head offic...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Configuring PPTP VPN in the Branch Office The IP address 69.1.121.30 is the Public IP address of the router located in head office. If you registered the DDNS (please refer to the DDNS section of this manual), you ...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Example: Configuring a IPSec LAN-to-LAN VPN Connection Table 3: Network Configuration and Security Plan Branch Office Head Office Local Network ID 192.168.0.0/24 192.168.1.0/24 Local Router IP 69.1.121.30 69.1.121....

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Example: Configuring a Remote Access L2TP VPN Dial-in Connection A remote worker establishes a L2TP VPN connection with the head office using Microsoft's VPN Adapter (included with Windows XP/2000/ME, etc.). The ro...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Example: Configuring a Remote Access L2TP VPN Dial-out Connection A company’s office establishes a L2TP VPN connection with a file server located at a separate location. The router is installed in the office, conne...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Configuring the L2TP VPN in the Office 1 2 3 5 6 4 Item Function Description 1 Connection Name VPN_L2TP Given name of L2TP connection Dial out Check Dial out 2 Server IP Address (or Hostname) 69.121.1.33 An Dialed ...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Example: Configuring your Router to Dial-in to the Server Currently, Microsoft Windows operation system does not support L2TP incoming service. Additional software may be required to set up your L2TP incoming servi...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Example: Configuring LAN-to-LAN L2TP VPN Connection The branch office establishes a L2TP VPN tunnel with head office to connect two private networks over the Internet. The routers are installed in the head office a...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration QoS (Quality of Service) QoS function helps you to control your network traffic for each application from LAN (Ethernet and/or Wireless) to WAN (Internet). It facilitates you to control the different quality and sp...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Prioritization There are three priority settings to be provided in the modem: High Normal (The default is normal priority for all of traffic without setting). Low The trigger of check can base on IP protocol, port ...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration IP Throttling IP Throttling allows you to limit the speed of IP traffic. The value entered will limit the speed of the application that you set to the specified value’s multiple of 32kbps. The trigger of check can ...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration For example, if you set the port number 80 (Web/HTTP) to be mapped to the IP Address 192.168.1.2, then all incoming HTTP requests from outside users will be forwarded to the local server (PC) with the IP address of...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Advanced Configuration options within the Advanced section are for users who wish to take advantage of the more advanced features of the router. Users who do not understand the features should not attempt to reconf...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Dynamic DNS The Dynamic DNS function allows you to alias a dynamic IP address to a static hostname, allowing users whose ISP does not assign them a static IP address to use a domain name. This is especially useful ...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Check Emails This function allows you to have the router check your POP3 mailbox for new Email messages. The Mail LED on your router will light when it detects new messages waiting for download. You may also view t...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Device Management The Device Management advanced configuration settings allow you to control your router’s security options and device monitoring features. Embedded Web Server: HTTP Port: This is the port number th...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration http:// 192.168.1.254:100 in their web browser. After 100 seconds, the device will automatically logout User A. Universal Plug and Play (UPnP): UPnP offers peer-to-peer network connectivity for PCs and other networ...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration SNMP Version: SNMPv2c and SNMPv3 SNMPv2c is the combination of the enhanced protocol features of SNMPv2 without the SNMPv2 security. The "c" comes from the fact that SNMPv2c uses the SNMPv1 community string...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Save Configuration to Flash After changing the router’s configuration settings, you must save all of the configuration parameters to FLASH to avoid them being lost after turning off or resetting your router. Click ...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 4: Configuration Logout To exit the router’s web interface, choose Logout . Please ensure that you have saved the configuration settings before you logout. Be aware that the router is restricted to only one PC accessing the configu...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 5: Troubleshooting Chapter 5: Troubleshooting If the router is not functioning properly, first check this chapter for simple troubleshooting before contacting your service provider or Billion support. Problems starting up the route...

Billion BIPAC-8500 / 8520 SHDSL VPN Firewall Bridge / Router Chapter 5: Troubleshooting Frequent loss of SHDSL linesync (disconnections). Ensure that all other devices connected to the same telephone line as your Billion router (e.g. telephones, fax machines, analogue modems) have a line filter conn...

Appendix A: APPENDIX A: Product Support and Contact Information Most problems can be solved by referring to the Troubleshooting section in the User’s Manual . If you cannot resolve the problem with the Troubleshooting chapter, please contact the dealer where you purchased this product. Contact Billi...