Billion 7404V - Manuals
Billion 7404V – Manual in PDF format online.
Manuals:
Manual Billion 7404V
Summary
T T a a b b l l e e o o f f C C o o n n t t e e n n t t s s CHAPTER 1: INTRODUCTION ............................................................................................................. 4 INTRODUCTION TO YOUR ROUTER................................................................................
DHCP Server .................................................................................................................................. 39 WAN - Wide Area Network.................................................................................................................. 40 ISP ............
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 1: Introduction Chapter 1: Introduction Introduction to your Router Welcome to the VoIP/(802.11g) ADSL2+ (VPN) Firewall Router. The router is an “all-in-one” VoIP ADSL router, combining an ADSL modem, ADSL router, Ethernet network switch and 2 port...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 1: Introduction directly for auto detection. Multi-Protocol to Establish a Connection It supports PPPoA (RFC 2364 - PPP over ATM Adaptation Layer 5), RFC 1483 encapsulation over ATM (bridged or routed), PPP over Ethernet (RFC 2516), and IPoA (RFC15...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 1: Introduction network, Internet. Rich Packet Filtering Not only filters the packet based on IP address, but also based on Port numbers. It will filter packets from and to the Internet, and also provides a higher level of security control. Dynamic...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 2: Installing the router Chapter 2: Installing the Router Important note for using this router Warning Do not use this router in high humidity or high temperatures. Do not use the same power source for this router as otherequipment. Do not open or ...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 2: Installing the router The Front LEDs LED Meaning 1 PWR Lit when power is ON. 2 SYS Lit when the system is ready. 3 – 6 LAN Port 1X — 4X (RJ-45 connector) Lit when connected to an Ethernet device. Green for 100Mbps; Orange for 10Mbps. Blinking wh...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 2: Installing the router The Rear Ports 1 3 5 6 2 4 8 7 The Ethernet Port # 4 can be used as a console port. You need a special console tool which already includes in the package to connect with LAN port 4 and PC’s RS-232 port (9-pin serial port). ...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 2: Installing the router 7 ADSL Connect the supplied RJ-11 (“telephone”) cable to this port when connecting to the ADSL/telephone network. 8 Antenna (Wireless Router only) Connect the detachable antenna to this port. Cabling One of the most common ...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 3: Basic Installation 11 Chapter 3: Basic Installation The router can be configured with your web browser. A web browser is included as a standard application in the following operating systems: Linux, Mac OS, Windows 98/NT/2000/XP/Me, etc. The pro...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 3: Basic Installation 12 Connecting Your Router 1. Connect this router to a LAN (Local Area Network) and the ADSL/telephone ( ADSL ) network. 2. Power on the device. 3. Make sure the PWR and SYS LEDs are lit steadily and that the LAN LED is lit. 4....
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 3: Basic Installation 13 Configuring PCs in Windows in Window XP 1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click Network Connections . 2. Double-click Local Area Connection . (See Figure 3.1) 3. In the LAN Area ...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 3: Basic Installation 14 Configuring PCs in Windows 2000 1. Go to Start / Settings / Control Panel . In the Control Panel, double-click Network and Dial-up Connections . 2. Double-click Local Area (“LAN”) Connection . (See Figure 3.5) 3. In the LAN...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 3: Basic Installation 16 Configuring PC in Windows NT4.0 1. Go to Start / Settings / Control Panel . In the Control Panel, double-click Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Properties . ( See Figure 3.12) 3. Sel...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 3: Basic Installation 17 Factory Default Settings Before configuring your, you need to know the following default settings. Web Interface (Username and Password) Username: admin Password: admin The default username and password are “ admin ” and “ ...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 3: Basic Installation 18 Information from your ISP Before configuring this device, you have to check with your ISP (Internet Service Provider) to find out what kind of service is provided such as DHCP (Obtain an IP Address Automatically, Static IP ...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 3: Basic Installation 19 Configuring with your Web Browser Open your web browser, enter the IP address of your router, which by default is 192.168.1.254 , and click “ Go ”, a user name and password window prompt will appear. The default username an...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Chapter 4: Configuration At the configuration homepage, the left navigation pane where bookmarks are provided links you directly to the desired setup page, including: Status - ARP Table - Wireless Association - Routing Table - DHCP...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Status ARP Table This section displays the router’s ARP (Address Resolution Protocol) Table, which shows the mapping of Internet (IP) addresses to Ethernet (MAC) addresses. This is useful as a quick way of determining the MAC addre...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Destination: The IP address of the destination network. Netmask: The destination Netmask address. Gateway/Interface: The IP address of the gateway or existing interface that this route will use. Cost: The number of hops counted as ...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Name: The name you assigned to the Permanent configuration. IP Address: The fixed IP address for the specify client. MAC Address: The MAC Address that you want to assign the fixed IP address. Maximum Lease Time: The maximum lease t...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration L2TP Status (Only the 7404VGO has VPN features) This shows details of your configured L2TP VPN Connections. Name: The name you assigned to the particular L2TP connection in your VPN configuration. Type: The type of connection (dial...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration VoIP Call Log This page displays the detailed log of each call. The maximum number of record is 30 entries for each phone port. (Dialed Calls List: 10, Received Calls List: 10, Missed Calls List: 10). Event Log This page displays t...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Error Log Any errors encountered by the router (e.g. invalid names given to entries) are logged to this window. NAT Sessions This section lists all current NAT sessions between interface of types external (WAN) and internal (LAN). ...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration UPnP Portmap The section lists all port-mapping established using UPnP (Universal Plug and Play. See Advanced section of this manual for more details on UPnP and the router’s UPnP configuration options. 27
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Quick Start For detailed instructions on configuring your WAN settings, please see the WAN section of this manual. Usually, the only details you will need for the Quick Start wizard to get you online are your login (often in the fo...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Select the desired option from the list and click Apply to return to the Quick Start interface to continue configuring your ISP connection. Please note that the contents of this list will vary, depending on what is supported by you...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Configuration When you click this item, you get following sub-items to configure the ADSL router. - LAN, Wan, System, Firewall, VPN, VoIP, QoS, Virtual Server, Time Schedule and Advanced These functions are described below in the f...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Ethernet Client Filter The Ethernet Client Filter supports up to 16 Ethernet network machines that helps you to manage your network control to accept traffic from specific authorized machines or can restrict unwanted machine(s) to ...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Active PC in LAN displays a list of individual Ethernet device’s IP Address & MAC Address which connecting to the router. You can easily by checking the box next to the IP address to be blocked or allowed. Then, Add to insert t...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration America (N.America), Europe, France, etc. The Channel ID will be different based on this setting. Channel ID: Select the wireless connection ID channel that you would like to use. Use the Scan Channel Usage to help to select non-oc...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Wireless Security (Wireless Router only) You can disable or enable with WPA or WEP for protecting wireless network. The default mode of wireless security is disabled . WPA-PSK (TKIP) / WPA-PSK (AES) Pre-Shared Key WPA Algorithms: T...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration WEP WEP Encryption: To prevent unauthorized wireless stations from accessing data transmitted over the network, the router offers highly secure data encryption, known as WEP. If you require high security for transmissions, there ar...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Port Setting This section allows you to configure the settings for the router’s Ethernet ports to solve some of the compatibility problems that may be encountered while connecting to the Internet, as well allowing users to tweak th...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration WAN - Wide Area Network WAN refers to your Wide Area Network connection, i.e. your router’s connection to your ISP and the Internet. Here are the items within the WAN section: ISP , DNS and ADSL . ISP The factory default is PPPoE. ...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration RFC 1483 Routed Connections Description: User-definable name for the connection. VPI and VCI: Enter the information provided by your ISP. ATM Class: The Quality of Service for ATM layer. NAT: The NAT (Network Address Translation) f...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration RFC 1483 Bridged Connections Description: User-definable name for the connection. VPI and VCI: Enter the information provided by your ISP. ATM Class: The Quality of Service for ATM layer. Encapsulation method: Select the encapsulat...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration PPPoA Routed Connections Description: User-definable name for the connection. VPI/VCI: Enter the information provided by your ISP. ATM Class: The Quality of Service for ATM layer. NAT: The NAT (Network Address Translation) feature ...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration IPoA Routed Connections Description: User-definable name for the connection. VPI/VCI: Enter the information provided by your ISP. ATM Class: The Quality of Service for ATM layer. NAT: The NAT (Network Address Translation) feature a...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration PPPoE Connections Description: User-definable name for this connection. VPI/VCI: Enter the information provided by your ISP. ATM Class: The Quality of Service for ATM layer. NAT: The NAT (Network Address Translation) feature allows...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration PPPoE with Pass-through Connections PPPoE with pass-through adapts the following method: PPPoE Routed mode + 1483 Bridge Mode. With pure PPPoE connection, the router can get one WAN address to the router. With the PPPoE and PPPoE p...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration DNS A Domain Name System (DNS) contains a mapping table for domain name and IP addresses. On the Internet, every host has a unique and user-friendly name (domain name) such as www.helloworld.com and an IP address. An IP address is ...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration ADSL Connect Mode: This mode will automatically detect your ADSL line code, ADSL2+, ADSL2, G.dmt, G.lite, T1.413, AnnexM2 and AnnexM2+. But in some area, multimode cannot detect the ADSL line code well. If it is the case, please ad...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Advanced Options ADSL Parameters help to interpret your ADSL line statistics. SNR Margin: It is known as Signal to Noise Ration Margin. It is the relative of DSL strength to Noise ratio. This margin is measured in decibels (dB). Hi...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration System Here are the items within the System section: Time Zone, Remote Access, Firmware Upgrade, Backup/Restore, Restart and User Management. Time Zone The router does not have a real time clock on board; instead, it uses the Simpl...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Remote Access To temporarily permit remote administration of the router (i.e. from outside your LAN), select a time period the router will permit remote access for and click Enable. You may change other configuration options for th...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Firmware Upgrade Your router’s “firmware” is the software that allows it to operate and provides all its functionality. Think of your router as a dedicated computer, and the firmware as the software it runs. Over time this software...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Restart Router Click Restart with option Current Settings to reboot your router (and restore your last saved configuration). If you wish to restart the router using the factory default settings (for example, after a firmware upgrad...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration User Management In order to prevent unauthorized access to your router’s configuration interface, it requires all users to login with a password. You can set up multiple user accounts, each with their own password. You are able to ...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Firewall and Access Control Your router includes a full SPI (Stateful Packet Inspection) firewall for controlling Internet access from your LAN, as well as helping to prevent attacks from hackers. In addition to this, when using NA...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Packet Filter This function is only available when the Firewall is enabled and one of these four security levels is chosen (All blocked, High, Medium and Low). The preset port filter rules in the Packet Filter must modify according...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Example: Predefined Port Filters Rules The predefined port filter rules for High, Medium and Low security levels are listed. See Table 1. Note: Firewall – All Blocked/User-defined, you must define and create the port filter rules y...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration 63 MSN (7001) UDP(17) 7001 7001 YES YES N/A N/A N/A N/A MSN VEDIO (9000) TCP(6) 9000 9000 NO YES N/A N/A N/A N/A Inbound: Internet to LAN ; Outbound: LAN to Internet. YES: Allowed ; NO: Blocked ; N/A: Not Applicable Packet Filter –...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Packet Filter – Add Raw IP Filter Rule Name: Users-define description to identify this entry or click to select existing predefined rules. Time Schedule: It is self-defined time period. You may specify a time schedule for your prio...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Configuring Packet Filter: 1. Click Port Filters . You will then be presented with the predefined port filter rules screen (in this case for the low security level), shown below: Note: You may click Edit the predefined rule instead...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration 5. The new port filter rule for HTTP is shown below: 6. Configure your Virtual Server (“port forwarding”) settings so that incoming HTTP requests on port 80 will be forwarded to the PC running your web server: Note: For how to conf...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Intrusion Detection The router’s Intrusion Detection System (IDS) is used to detect hacker attacks and intrusion attempts from the Internet. If the IDS function of the firewall is enabled, inbound packets are filtered and blocked d...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Table 2: Hacker attack types recognized by the IDS Intrusion Name Detect Parameter Blacklist Type of Block Duration Drop Packet Show Log Ascend Kill Ascend Kill data Src IP DoS Yes Yes WinNuke TCP Port 135, 137~139, Flag: URG Src I...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration URL Filter URL (Uniform Resource Locator – e.g. an address in the form of http://www.abcde.com or http://www.example.com ) filter rules allow you to prevent users on your network from accessing particular websites by their URL. The...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration dropped. 3. If the packet does not match either of the above two items, it is sent to the remote web server. 4. Please be note that the completed URL, “www” + domain name shall be specified. For example to block traffic to www.goog...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Firewall Log Firewall Log display log information of any unexpected action with your firewall settings. Check the Enable box to activate the logs. Log information can be seen in the Status – Event Log after enabling. 73
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration PPTP Connection - Remote Access Connection Name: User-defined name for the connection (e.g. “connection to office”). Type: Check Dial Out if you want your router to operate as a client (connecting to a remote VPN server, e.g. your ...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Example: Configuring a Remote Access PPTP VPN Dial-out Connection A company’s office establishes a PPTP VPN connection with a file server located at a separate location. The router is installed in the office, connected to a couple ...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration PPTP Connection - LAN to LAN Connection Name: User-define description of the connection. Type: Check Dial Out if you want your router to operate as a client (connecting to a remote VPN server, e.g. your office server), check Dial I...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Example: Configuring a PPTP LAN-to-LAN VPN Connection The branch office establishes a PPTP VPN tunnel with head office to connect two private networks over the Internet. The routers are installed in the head office and branch offic...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Configuring PPTP VPN in the Head Office The IP address 192.168.1.201 will be assigned to the router located in the branch office. Please make sure this IP is not used in the head office LAN. 1 2 3 4 5 6 Item Function Description 1 ...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration IPSec VPN Connection Connection Name: User-defined name for the connection (e.g. “connection to office”). Local Network: Set the IP address, subnet or address range of the local network. Single Address: The IP address of the local ...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration 3DES: Stands for Triple Data Encryption Standard, it uses 168 (56*3) bits as an encryption method. AES: Stands for Advanced Encryption Standards, you can use 128, 192 or 256 bits as encryption method. Perfect Forward Secrecy: Choos...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration AES: Stands for Advanced Encryption Standards, you can use 128, 192 or 256 bits as encryption method. Diffie-Hellman Group: It is a public-key cryptography protocol that allows two parties to establish a shared secret over an unsec...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Example: Configuring a IPSec LAN-to-LAN VPN Connection Table 3: Network Configuration and Security Plan Branch Office Head Office Local Network ID 192.168.0.0/24 192.168.1.0/24 Local Router IP 69.1.121.30 69.1.121.3 Remote Network ...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Configuring IPSec VPN in the Office 1 2 Item Function Description 1 Connection Name IPSec Given a name of IPSec connection Subnet Check Subnet radio button IP Address 192.168.1.0 2 Netmask 255.255.255.0 Head office network 3 Secure...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration L2TP Connection - Remote Access L2TP VPN Connection Connection Name: User-defined name for the connection (e.g. “connection to office”). Type: Check Dial Out if you want your router to operate as a client (connecting to a remote VP...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Example: Configuring a L2TP VPN - Remote Access Dial-in Connection A remote worker establishes a L2TP VPN connection with the head office using Microsoft's VPN Adapter (included with Windows XP/2000/ME, etc.). The router is install...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Example: Configuring a Remote Access L2TP VPN Dial-out Connection A company’s office establishes a L2TP VPN connection with a file server located at a separate location. The router is installed in the office, connected to a couple ...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Example: Configuring L2TP LAN-to-LAN VPN Connection The branch office establishes a L2TP VPN tunnel with head office to connect two private networks over the Internet. The routers are installed in the head office and branch office ...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration VoIP - Voice over Internet Protocol VoIP enables telephone calls through existing Internet connection instead of going through the PSTN (Public Switched Telephone Network). It is not only cost-effective, especially for a long dista...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Wizard This section provides easy setup for your VoIP service. Phone port 1 and 2 can be registered to different SIP Service Provider. Voice QoS DSCP Marking : Differentiated Services Code Point (DSCP), it is the first 6 bits in th...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Setting for Phone Port 2 Click box of Same as Phone Port 1 to set phone port 2 be identical as phone port 1. Please refer to descriptions in “Setting for Phone Port 1”. User-defined Profiles Note: User defined profiles are limited ...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Authentication Password: This parameter holds the password used for authentication within VoIP SIP registrar. Confirm Password: Re-enter the password for confirmation. Display Name: This parameter will be appeared on the Caller ID....
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Advanced – Parameters VoIP through IP Interface: IP Interface decides where to send/receive the voip traffic; it includes: ipwan and iplan. Easy way to select the interface is to check the location of the SIP server. If it locates ...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration OFFHOOK voltage to the lowest setting registered for all your telephones, e.g. if your telephones return values of 4, 5 and 7 then you should set your OFFHOOK voltage to 4. Note: The detected values will not automatically be set by...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration PSTN Dial Plan (Router with LINE port only) This section enables you to configure “VoIP with PSTN switching” on your system. You can define a range of dial plans to make regular call from VoIP switching to PSTN line. Prefix numbers...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration PSTN Dial Plan Examples: 1) Dial with Prefix If you dial 01223 707070, number 01223707070 will be dialed out via FXO to make a regular phone call. 2) Dial without Prefix If you dial 9102, the number 102 will only be dialed out via ...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration VoIP Dial Plan This section helps you to make a telephony number dialed as making a regular call via VoIP. You no longer need to memorize a long dial string of number for making a VoIP call. Parameters A listed of special dial feat...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Appendix A: Product Support and Contact Information Note: Refer to Special Dial Code section in this Manual for more details. Test: It is a tool to help to identify the call number is being properly being processed prior to making an actual call. Click App...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Appendix A: Product Support and Contact Information # (pound sign): It is normal character ‘#’ on phone key pad. Please check if it is provided by your VoIP Service Provider or Local Telephone Service Provider for special service(s). <@ Current Profile&...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Appendix A: Product Support and Contact Information Localcheap.com is the default VoIP provider I set on phone port 1. When I call out any number start with 1 or 2 or 3 and plus rest of the phone number for local call, 03 is always prepended in front of th...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Appendix A: Product Support and Contact Information Mobilecheap.com is the default VoIP provider I set on phone port 2. When I call out 123-39-45678 for a mobile call, 123 is replaced with 09. Therefore, 09-39-45678 is the actual phone number called out vi...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration QoS - Quality of Service QoS function helps you to control your network traffic for each application from LAN (Ethernet and/or Wireless) to WAN (Internet). It facilitates you to control the different quality and speed of through pu...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Source IP Address Range : The source IP address or range of packets to be monitored. Destination IP address Range : The destination IP address or range of packets to be monitored. DSCP Marking : Differentiated Services Code Point (...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Example: QoS for your Network Connection Diagram Normal PCs VoIP Restricted PC Information and Settings Upstream: 928 kbps Downstream: 8 Mbps VoIP User : 192.168.1.1 Normal Users : 192.168.1.2~192.168.1.5 Restricted User: 192.168.1...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Mission-critical application Mostly the VPN connection is mission-critical application for doing data exchange between head and branch office. The mission-critical application must be sent out smoothly without any dropping. Set pri...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Virtual Server (known as Port Forwarding) In TCP/IP and UDP networks a port is a 16-bit number used to identify which application program (usually a server) incoming connections should be delivered to. Some ports have numbers that ...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Add Virtual Server Because NAT can act as a “natural” Internet firewall, your router protects your network from being accessed by outside users when using NAT, as all incoming connection attempts will point to your router unless yo...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Example: If you like to remote accessing your Router through the Web/HTTP at all time, you would need to enable port number 80 (Web/HTTP) and map to Router’s IP Address. Then all incoming HTTP requests from you (Remote side) will b...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Example: List of some well-known and registered port numbers. The Internet Assigned Numbers Authority (IANA) is the central coordinator for the assignment of unique parameter values for Internet protocols. Port numbers range from 0...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Time Schedule The Time Schedule supports up to 16 time slots which helps you to manage your Internet connection. In each time profile, you may schedule specific day(s) i.e. Monday through Sunday to restrict or allowing the usage of...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Configuration of Time Schedule Edit a Time Slot 1. Choose any Time Slot (ID 1 to ID 16) to edit, click Edit. Click Edit Note: Watch it carefully, the days you have selected will present in capital letter. Lower case letter shows th...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Dynamic DNS The Dynamic DNS function allows you to alias a dynamic IP address to a static hostname, allowing users whose ISP does not assign them a static IP address to use a domain name. This is especially useful for hosting serve...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Device Management The Device Management advanced configuration settings allow you to control your router’s security options and device monitoring features. Embedded Web Server ( 2 Management IP Accounts) HTTP Port: This is the port...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration address 192.168.1.55 to logon to the Web GUI by typing: http:// 192.168.1.254:100 in their web browser. After 100 seconds, the device will automatically logout User A. Universal Plug and Play (UPnP) UPnP offers peer-to-peer network...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration IGMP IGMP, known as Internet Group Management Protocol , is used to management hosts from multicast group. IGMP Forwarding: Accepting multicast packet. Default is set to Enable. IGMP Snooping: Allowing switched Ethernet to check an...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Ethernet1: P2, P3 and P4 (Port 2, 3, 4) Please uncheck P2, P3, P4 from Ethernet VLAN Port first. Note: You should setup each VLAN group with caution. Each Bridge Interface is arranged in this order. Bridge Interface VLAN Port (Alwa...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Step 3: Setup VLAN Service Go to Configuration Advanced VLAN Bridge DefaultVlan lists all member ports. It is necessary to group specific member ports for each VLAN. From the example, two VLAN groups are requested: Data and Video. ...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Mapping the VLAN Bridge with Bridge Interface created in Step1, you will see the conformable relationship in these two screenshots. Step 4: IGMP Snooping Enable Go Configuration Advanced IGMP . IGMP Snooping must be enabled in orde...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 4: Configuration Logout To exit the router’s web interface, choose Logout . Please ensure that you have saved the configuration settings before you logout. Be aware that the router is restricted to only one PC accessing the configuration web pages ...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Appendix A: Product Support and Contact Information Chapter 5: Troubleshooting If the router is not functioning properly, first check this chapter for simple troubleshooting before contacting your service provider or Billion support. Problems starting up t...
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Appendix A: Product Support and Contact Information APPENDIX A: Product Support and Contact Information Most problems can be solved by referring to the Troubleshooting section in the User’s Manual . If you cannot resolve the problem with the Troubleshootin...
Billion Manuals
-
Billion 2073
Manual
-
Billion Dual-Port ADSL2+ Modem/Router
Manual
-
Billion BiPAC 2073
Manual
-
Billion BiGuard 50G
Manual
-
Billion S100N
Manual
-
Billion 3013G
Manual
-
Billion BIPAC-7100S
Manual
-
Billion BiGuard Series
Manual
-
Billion VoIP/(802.11g) ADSL2+ Router
Manual
-
Billion BIPAC 7500
Manual
-
Billion BIPAC-7100S, BIPAC-7100
Manual
-
Billion BIPAC 3012G
Manual
-
Billion CO1
Manual
-
Billion 3011G
Manual
-
Billion BIPAC-7100
Manual
-
Billion BIPAC-221
Manual
-
Billion 30
Manual
-
Billion ISDN TA128s
Manual
-
Billion BIPAC 2071
Manual
-
Billion 5210S
Manual