Page 3 - Table of Contents
i Table of Contents Chapter 1 ........................................................................................................... 1 Introduction........................................................................................................................... 1 1.1 An Overview of BIP...
Page 4 - Billion BIPAC 7100S ADSL Modem/Router; ii
Billion BIPAC 7100S ADSL Modem/Router ii 3.4.3.4.5 URL Blocking .......................................................................................... 36 3.4.3.5 VPN (Virtual Private Networks) ..................................................................... 37 3.4.3.6 Virtual Server ..........
Page 6 - Package Contents; Multi-Protocol to Establish A Connection:
Billion BIPAC 7100S ADSL Modem/Router 2 1.2 Package Contents 1. Billion BIPAC 7100S ADSL Modem/Router 2. One CD-ROM containing the driver and online manual 3. One Quick Start Guide 4. One RJ-11 ADSL/telephone cable 5. One CAT-5 straight LAN cable 6. One power adapter 1.3 BIPAC 7100S Features BIPAC 7...
Page 7 - Chapter 1 Introduction; In the WAN site, the DHCP client can; Rich Packet Filtering:; Allows user to make a tunnel with a remote site directly to secure
Chapter 1 Introduction 3 example, user can assign a PC in LAN acting as WEB server inside and expose it to the outside network. Outside user can browse inside web server directly while it is protected by NAT. A DMZ host setting is also provided to a local computer exposed to the outside network, Int...
Page 8 - Cautions for Using Billion ADSL Modem/Router; Do not place the router under high humidity and high temperature.; Lit green when power adapter is connected.
4 Chapter 2 Using Billion ADSL Modem/Router 2.1 Cautions for Using Billion ADSL Modem/Router Do not place the router under high humidity and high temperature. Do not use the same power source for the device with other equipment. Do not open or repair the case yourself. If the device is too hot, turn...
Page 9 - Chapter 2 Using the ADSL Modem/Router; Reset; A Power ON/OFF switch; Through Ethernet Port
Chapter 2 Using the ADSL Modem/Router 5 2.3 The Rear Ports LINE (RJ-11 connector) Connect the supplied RJ-11 cable to this port when connecting to the ADSL Reset Press it to restore the factory default setting back LAN (RJ-45 connector) Connect the supplied crossover cable to this port when connecti...
Page 10 - “3.2 Configuring the
Billion BIPAC 7100S ADSL Modem/Router 6 So long as the cables are connected and the LEDs are lit normally, follow section “3.2 Configuring the Network Properties” below to modify the network settings. Since the product cannot auto-detect whether your cable is correct or not, please make sure you are...
Page 11 - Before Configuration; Configuring PC in Windows XP; Go to; Network
7 Chapter 3 Configuration BIPAC 7100S can be configured with your Web browser. The web browser is included as a standard application in following operation systems, UNIX, Linux, Mac OS, Windows 95/98/NT/2000/Me/XP, etc. The product provides a very easy and user-friendly interface for configuration. ...
Page 12 - In the; Local Area Connection; Select; Properties
Billion BIPAC 7100S ADSL Modem/Router 8 3. In the Local Area Connection Status window, click Properties . 4. Select Internet Protocol (TCP/IP) and click Properties .
Page 13 - Chapter 3 Configuration; Configuring PC in Windows 2000
Chapter 3 Configuration 9 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration. Configuring PC in Windows 2000 1. Go to Start / Settings / Control Panel . In the Control Panel, double- click on Network...
Page 17 - Configuring PC in Windows NT4.0; Panel; click on; and choose the; Protocols
Chapter 3 Configuration 13 Configuring PC in Windows NT4.0 1. Go to Start / Settings / Control Panel . In the Control Panel, double- click on Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Properties .
Page 18 - Factory Default Settings
Billion BIPAC 7100S ADSL Modem/Router 14 3. Select the Obtain an IP address from a DHCP server radio button and click OK . 3.2 Factory Default Settings Before you configure this device, you need to know the following default settings. 1. Web Configuration Password: There are two levels of password p...
Page 19 - LAN Port; Enabled; Information from ISP; PPPoE
Chapter 3 Configuration 15 3.2.1 Password The default username and password are admin and password respectively. If you ever forget the password to log in, you may press the RESET button up to 2 seconds to restore the factory default settings. 3.2.2 LAN and WAN Port Addresses The parameters of LAN a...
Page 20 - IPoA; Configuring with Web Browser; Go; ” to get the login page.; admin; in the username field and; password; to log in. You can modify these passwords for security
Billion BIPAC 7100S ADSL Modem/Router 16 IPoA VPI/VCI, VC-based/LLC-based multiplexing, IP address, Subnet mask, Gateway address, and Domain Name System (DNS) IP address (it is fixed IP address). 3.4 Configuring with Web Browser The ADSL Modem/Router can be configured with your Web browser. The web ...
Page 21 - Quick Start; Routing Table and VPN Connect Status)
Chapter 3 Configuration 17 At the configuration homepage, the left navigation pane where bookmarks are provided links you directly to the desired setup page, including: Quick Start Configuration (LAN, WAN, Firewall, System, VPN, Virtual Server, Advanced and Help) Status (System Status, Device Info, ...
Page 23 - Displays the status of your Local Area Network (LAN) connection.
Chapter 3 Configuration 19 3.4.1.1.2 ADSL Status – ATM Status 3.4.1.2 Status – LAN Status Displays the status of your Local Area Network (LAN) connection.
Page 25 - Enter the time period for the router to memorize MAC addresses.
Chapter 3 Configuration 21 3.4.1.4 Status- Learned MAC Table Aging Timeout: Enter the time period for the router to memorize MAC addresses. 3.4.1.5 Routing Table Display the current routing paths of BIPAC 7100S.
Page 27 - Information from the; Apply; button and then click the; Save
Chapter 3 Configuration 23 3.4.2 Quick Start If you use this device to access the Internet through the ISP, this web page is enough for you to configure this router and access the Internet without a problem. Please check Chapter 3.3 ( Information from the ISP) , then enter the proper values into thi...
Page 28 - Select the item of; PVCs
Billion BIPAC 7100S ADSL Modem/Router 24 Select the item of PVCs you want to configure. Then, press the Submit button.
Page 29 - Virtual Circuit; the settings of this VC.
Chapter 3 Configuration 25 Virtual Circuit Virtual Circuit: Enable/Disable the settings of this VC. Bridge: If you set this device to be bridge mode, select Enable; if not, please select Disable. IGMP: You can Enable or Disable this function. Encapsulation: There are eleven ways ─ PPPoE VC-Mux, PPPo...
Page 31 - when disconnected by ISP.; Device IP Address; Auto or User Defined. If select the AUTO, router will assign an IP; User Defined Start Address:
Chapter 3 Configuration 27 Automatic Reconnect: Check to enable this device to automatically re-establish the PPPoE session when disconnected by ISP. 3.4.3.2 LAN This screen contains settings for LAN interface attached to the LAN port. Device IP Address IP Address: Default at 192.168.1.254. This is ...
Page 32 - System
Billion BIPAC 7100S ADSL Modem/Router 28 With this case, the DHCP pool is from 192.168.1.100 to 192.168.1.199. Therefore, the local computer will get an IP address located at this range randomly. Lease Time: Set the lease time you required. User Mode: There are two selections, Single User and Multi-...
Page 33 - Automatically adjust clock for daylight saving changes:; It is optional for different time zone area.; SNTP Server IP Address:; Specify the IP address if you want to use your familiar SNTP server.
Chapter 3 Configuration 29 3.4.3.3.2 Time Zone BIPAC 7100S does not have a real time clock on board; instead, it uses the simple network time protocol (SNTP) to get the current time from the SNTP server in outside network. Please choose your local time zone and click Submit. You will get the correct...
Page 34 - “Browse...”; button to specify the path of the firmware file. Then, click; “Upgrade”; to make the new firmware work.
Billion BIPAC 7100S ADSL Modem/Router 30 3.4.3.3.3 Upgrade To upgrade the firmware of BIPAC 7100S, you should download or copy the firmware to your local environment first. Press the “Browse…” button to specify the path of the firmware file. Then, click “Upgrade” to start upgrading. When the procedu...
Page 35 - Submit
Chapter 3 Configuration 31 3.4.3.3.5 Restart In case the router stops responding correctly or in some other way stops functioning, you can perform the restart. Your setting won’t be changed. Performing the restart, click on the Submit button.
Page 36 - IP; ) from Internet access, or you can disable specific service request (; Port number
Billion BIPAC 7100S ADSL Modem/Router 32 3.4.3.4 Firewall User can decide to enable this firewall function including Packet Filter, Block Hacker Attack, and Block WAN request features for better security control or not. But be noted, it wastes network processor computation power. The performance wil...
Page 39 - Snork Attack
Chapter 3 Configuration 35 - Snork Attack - UDP port loop-back - TCP NULL scan 3.4.3.4.4 Block WAN Request Check “Enable” if you want to exclude outside PING request from reaching on this router.
Page 40 - “Enable”; : Check this will block all browsing requests from PCs; Use Domain Filtering:; to enter further information.
Billion BIPAC 7100S ADSL Modem/Router 36 3.4.3.4.5 URL Blocking URL blocking function enables you to avoid your LAN PCs from accessing some URLs. You must check the “Enable” radio button to make the following figure appear for further configuration. Always Block : Check this will block all browsing ...
Page 41 - Active; : To enable this VPN tunnel setting or not.; Remote Gateway IP or Host Name:; the public IP address or host name of remote VPN device. For
Chapter 3 Configuration 37 3.4.3.5 VPN (Virtual Private Networks) we will introduce the VPN settings to establish a secure communication path with remote site based on IPsec. Please check “Enable” and click “Add” button. Then you will see IKE Setup page as below figure. Then, you can configure the r...
Page 42 - sides should use the same key.
Billion BIPAC 7100S ADSL Modem/Router 38 Remote Subnet Mask: The range of remote IPs can be communicated. For example, it is 255.255.255.0. Proposal: There are two methods to check the authentication information, AH (authentication header) and ESP (Encapsulating Security Payload). ESP: Data will be ...
Page 43 - Enter the public port number & range you want to configure.
Chapter 3 Configuration 39 3.4.3.6 Virtual Server Being a natural Internet firewall, the ADSL Router protects your network from being accessed by outside users. When it needs to allow outside users to access internal servers, e.g. Web server, FTP server, E-mail server or News server, this product ca...
Page 44 - TCP
Billion BIPAC 7100S ADSL Modem/Router 40 Port Type: Select TCP if you want to scope for the connection-based application service on the remote server using the port number. Or select UDP if you want to scope for the connectionless application service on the remote server using the port number. Host ...
Page 46 - NAT Configuration
Billion BIPAC 7100S ADSL Modem/Router 42 Check the “Enable” button to access the Dynamic DNS service. You may sign up Dynamic DNS service at http://www.dyndns.org T and there you can also register domain names. Host: Enter one domain name you have registered. User Name: Enter the username used for s...
Page 47 - Session Name Configuration,
Chapter 3 Configuration 43 User’s IP: Allows the user to assign the IP address to map the corresponding NAT/NAPT sessions. Session Name status will be displayed at the middle of this page to show the corresponding Session Name with its IP address. Click Session Name Configuration, the following scre...
Page 48 - Disabled; Default is; The default value is 30 seconds.; Expire Timeout; The default value is 180 seconds.; Garbage Timeout; The default value is 120 seconds.
Billion BIPAC 7100S ADSL Modem/Router 44 3.4.3.7.5 RIP RIP: Default is Disabled . Border Gateway: Default is Enabled . Supply Interval seconds: The default value is 30 seconds. Expire Timeout seconds: The default value is 180 seconds. Garbage Timeout seconds: The default value is 120 seconds.
Page 49 - SNMP System Identification:
Chapter 3 Configuration 45 3.4.3.7.6 SNMP Simple Network Management Protocol (SNMP) is an optional feature that may or may not be supported by your ADSL Bridge/Router. SNMP is an application layer protocol that is used for managing networks. SNMP is an optional feature that may or may not be in the ...
Page 50 - Check the item you want to delete. Then, click the “Delete” button.
Billion BIPAC 7100S ADSL Modem/Router 46 3.4.3.7.7 Static Routing If you have another router with a LAN-to-LAN connection, you may create a static routing on the router that is the gateway to Internet. Add: Click this button to add a new static routing. When you click this button, the next figure ap...
Page 52 - Checking LAN Connection; Testing Ethernet LAN connection; Checking ADSL Connection; Testing ADSL Synchronization; If this test returns FAIL, all other tests will be skipped.; Test ATM OAM Segment Loop Back; This test returns FAIL if the DSL synchronization test failed.
Billion BIPAC 7100S ADSL Modem/Router 48 Checking LAN Connection Testing Ethernet LAN connection This test passes if the Ethernet LAN interface is working properly. Checking ADSL Connection Testing ADSL Synchronization This test checks your DSL modem to see if it can successfully negotiate and estab...
Page 53 - This test returns SKIPPED if the DSL synchronization test failed.; Test Ethernet connect to ATM; Test Internet connection
Chapter 3 Configuration 49 Test ATM OAM End-to-End Loop Back This test sends ATM OAM F5 End-to-End loop back request cells to the central office equipments through your DSL connection. This test returns PASS if response cell is received. Since your service provider might not support this test, your ...
Page 54 - Click the
3.4.4 Save Config Click the Submit button to write settings to flash. Then, the system will reboot for changes to take effect. 50
Page 55 - Can’t connect to ISP.
51 Chapter 4 Troubleshooting If the ADSL Router is not functioning properly, you can refer first to this chapter for simple troubleshooting before contacting your service provider. This could save your time and effort but if the symptoms persist, then consult your service provider. Problems Starting...
Page 56 - Most problems can be solved by referring to the; Contact Billion
52 APPENDIX Product Support and Contact Information Most problems can be solved by referring to the Troubleshooting section in the User’s Manual . If you cannot resolve the problem with the Troubleshooting chapter, please contact the dealer where you purchased this product. Contact Billion AUSTRALIA...
Billion 2073
Manual
Billion Dual-Port ADSL2+ Modem/Router
Manual
Billion BiPAC 2073
Manual
Billion BiGuard 50G
Manual
Billion S100N
Manual
Billion 3013G
Manual
Billion BIPAC-7100S
Manual
Billion BiGuard Series
Manual
Billion VoIP/(802.11g) ADSL2+ Router
Manual
Billion BIPAC 7500
Manual
Billion BIPAC 3012G
Manual
Billion CO1
Manual
Billion 3011G
Manual
Billion BIPAC-221
Manual
Billion 30
Manual
Billion ISDN TA128s
Manual
Billion BIPAC 2071
Manual