Belkin P74080 - Manuals

Belkin P74080 – Manual in PDF format online.

Manuals:

Manual

Manual Belkin P74080

Summary

Page 3 - TABLE OF CONTENTS

TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2Assembling Your Drive Enclosure . . . . . . . . . . . . . . . . . . . . . . . . .3Driver Installation...

Page 5 - INTRODUCTION

The Hi-Speed USB 2.0 External Drive Enclosure (the External Drive) isa portable compact storage drive that incorporates the USB 2.0(Universal Serial Bus 2.0) high-speed interface. The External Driveprovides a fast and easy way to add more storage space to yourcomputer. The Plug-and-Play feature give...

Page 6 - SYSTEM REQUIREMENTS; Hardware; Notebook and desktop computer with USB 1.0 or USB 2.0 port; Operating System; Windows

SYSTEM REQUIREMENTS 2 Hardware Notebook and desktop computer with USB 1.0 or USB 2.0 port Operating System Windows ® 98 SE, Me, 2000, or XP P74080-F5U209-man_8-02.qxd 8/26/02 12:36 PM Page 2

Page 7 - ASSEMBLING YOUR DRIVE ENCLOSURE; Remove top of the External Drive.

ASSEMBLING YOUR DRIVE ENCLOSURE 3 1. Remove top of the External Drive. 2. If you are installing a 3 1 / 2 -inch hard drive, check to make sure your drive is set to “Master” (see jumper settinginformation printed on top of your disk drive), thenconnect the 34-position data cable and 4-positionpower c...

Page 8 - There are four fine-threaded screws, and four

ASSEMBLING YOUR DRIVE ENCLOSURE 4 Note: There are four fine-threaded screws, and four course-threaded screws included with your Hi-Speed ExternalDrive Enclosure Kit. Be sure to choose the screws that matchthe mounting holes for your drive. Do not try to force a course-threaded screw into a fine-thre...

Page 10 - If you are using Windows 98 or 98 SE, DO

ASSEMBLING YOUR DRIVE ENCLOSURE 6 8. Insert the mounting tabs on the free end of the front panelinto the second side rail, and hook the side rail onto thefront of the External Drive. 9. Finish the assembly by pressing the rail into the sixrectangular mounting holes in the side of the External Drive....

Page 11 - maximum USB bandwidth will be 12 Mbps.

ASSEMBLING YOUR DRIVE ENCLOSURE 7 10. Plug the square-shaped connector of the USB cable intothe USB port on the rear panel of the External Drive. 11. Plug the rectangular-shaped connector of the USB cable into a Hi-Speed USB 2.0 port on your computer orHi-Speed USB 2.0 hub. You may also connect the ...

Page 12 - DRIVER INSTALLATION; Insert the installation CD into your CD-ROM drive.

DRIVER INSTALLATION 8 Windows 98 SE 1. Insert the installation CD into your CD-ROM drive. 2. Open the Install CD. 3. Run the “TPPINST.EXE” to install the drivers for yourUSB 2.0 External Drive. 4. An installer dialog box appears. Click “Next”. 5. Choose “Complete” and click “Next”. 6. You may now co...

Page 13 - If the new drive does not appear in My Computer, you

DRIVER INSTALLATION 9 Note: If the new drive does not appear in My Computer, you may need to partition and format the drive. Please refer to the“Format the USB 2.0 External Drive” section to prepare yourUSB 2.0 hard disk drive. A green “Unplug or Eject Hardware” icon will appear in the system tray. ...

Page 14 - Select the “USB Mass Storage Device” then click “Stop”.

SAFE REMOVAL OF THE USB DISK FROM WINDOWS 10 Windows 98 1. Click the green “Unplug or Eject Hardware” icon in thesystem tray and select the device that you want to remove. 2. When the system prompts “You may safely remove thisdevice”, unplug the USB cable from the USB port of your computer. Windows ...

Page 15 - FORMAT THE USB 2.0 EXTERNAL DRIVE; Format under Windows 98/Me; Boot-up the computer into the Windows operating system.; Control Panel Method; Click “Start” and choose “Setting”.

FORMAT THE USB 2.0 EXTERNAL DRIVE 11 Format under Windows 98/Me 1. Boot-up the computer into the Windows operating system. 2. Plug in your External Drive. There are two methods to partition and format yourUSB 2.0 hard disk drive. Control Panel Method 1. Click “Start” and choose “Setting”. 2. Choose ...

Page 16 - Your removable hard drive is now ready for use.

FORMAT THE USB 2.0 EXTERNAL DRIVE 12 5. Select “Disk Drives”. Your new hard disk will appear in thehard drive list (in this case as “Toshiba 1924FCV”). 6. Double-click on the entry for your hard drive. Select“Settings”. The following screen will appear. 7. Make sure there are check marks in the “Dis...

Page 17 - DOS Method (Recommended for Advanced Users Only)

FORMAT THE USB 2.0 EXTERNAL DRIVE 13 DOS Method (Recommended for Advanced Users Only) 1. Click on “Start”, and choose “Programs”. Select “MSDOS”. 2. At the DOS prompt, type “FDISK” and press “Enter”. Note: If the FDISK utility terminates without displaying an error message, exit back to Windows and ...

Page 18 - IMPORTANT

FORMAT THE USB 2.0 EXTERNAL DRIVE 14 IMPORTANT Be sure that you select option 5 and change the “Current Fixed Disk” from “Disk 1” to the disk number assigned to yourExternal Drive. If your computer is equipped with only oneinternal drive, your new External Drive will be identified as“Disk 2”. If you...

Page 19 - If you are viewing the Control Panel in classic mode,

FORMAT THE USB 2.0 EXTERNAL DRIVE 15 Note: If you are viewing the Control Panel in classic mode, proceed directly to “Administrative Tools”. 2. Click on “Disk Management”. All connected disk drives willbe displayed in the lower right-hand corner of the“Computer Management” window. Information regard...

Page 20 - INFORMATION; FCC Statement

INFORMATION FCC Statement DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY We, Belkin Corporation, of 501 West Walnut Street, Compton, CA 90220,declare under our sole responsibility that the product: F5U209 to which this declaration relates:Complies with Part 15 of the FCC ...