Belkin F6C110-RKM-2U - Manuals

Page 4 - Benefits; • Enterprise Design

OVERVIEW 6 HIGHLIGHTS 7 The Belkin OmniGuard Rackmount UPS (Figure 1) offers a 2U or 3U design with acapacity range of 1100VA/660 watts to 3200VA/1920 watts of true sine-waveoutput. Fig. 1: Belkin OmniGuard Rackmount UPS Designed to save rack space for increasing density within an enterpriseenvironm...

Page 5 - Please save ALL packing materials!; • Software Manageability

HIGHLIGHTS 8 PACKAGE CONTENTS 9 Please review the contents of the box to ensure you have all the correct partsneeded to correctly install and use the system. • OmniGuard Rackmount UPS • 6 ft. RS232 communication cable • Pair of standard black brackets for 19" • Installation manual • Warranty car...

Page 6 - Elevated Operating Ambient Temperature.

QUICK START 10 PRODUCT INSTALLATION 11 To install the OmniGuard Rackmount UPS, the following steps should befollowed: 1. Find a proper location for the UPS device. 2. Mount the device into an appropriate rack or alternative configuration. 3. Verify that you’re using an appropriate connector and plug...

Page 7 - Attaching the Brackets to the Rack; Diagram 1: Mounting the UPS into the Rack; Use two or more people when installing the UPS into; Connecting to an AC Power Source; After plugging in the UPS, check the Site Wiring Fault (SWF) LED on; PRODUCT INSTALLATION; If the UPS indicates a site-wiring fault, have a

13 12 Mounting the UPS within the Rack The OmniGuard Rackmount UPS includes a mounting kit, which includes twomounting brackets for a standard 19-inch (48.3cm) rack and eight retainingscrews for mounting the brackets to the UPS device. Note that the screws andnats necessary for mounting the UP actua...

Page 8 - PRODUCT DIAGNOSTICS; Connecting your Equipment; The computer interface port is for the UPS monitoring and control.; Do not connect a laser printer to the battery backup

PRODUCT DIAGNOSTICS 15 14 Connecting your Equipment Plug the equipment into the output receptacles on the back panel of the unit. Ifyour UPS is a 3U rack, there are a total of eight outlets, with seven outletsproviding backup plus surge protection and one outlet for surge-only protection.However, if...

Page 9 - Turning the Unit On/Off

PRODUCT DIAGNOSTICS 16 PRODUCT DIAGNOSTICS 17 Turning the Unit On/Off Press and release the “ON/OFF/TEST” switch. After one beep theunit will turn on and supply power to the load. The load isimmediately powered while the UPS runs a five-second self-test. Press and release the switch (after one beep)...

Page 10 - Alarms; UPS FAULT; Communications Port

PRODUCT DIAGNOSTICS 18 PRODUCT DIAGNOSTICS 19 Alarms ON-BATTERY When the UPS is operating on the batteries, the On-Line LED will blink and theaudible alarm will sound every 10 seconds. The alarm will stop once the UPSreturns to On-Line operation. UPS FAULT When the UPS detects a hardware fault, the ...

Page 11 - Communications Port Connection; Setting Up Windows Internal Power Management for UPS Service

SOFTWARE FEATURES & INSTALLATION 20 SOFTWARE FEATURES & INSTALLATION 21 Communications Port Connection Setting Up OmniGuard Power Management Software and The Interface Cable Power Management software and interface cable kits can be used with the UPS.Use only approved interface cables with th...

Page 13 - Battery Replacement; Symptom

MAINTENANCE 25 FAQS 24 Battery Replacement The OmniGuard Rackmount series has easy-to-replace hot-swappable batteries.Please read the following warning statements before attempting to service thebattery(s). NOTE: If there is a power interruption while replacing the hot-swappable batteries, with the ...

Page 14 - OmniGuard TM Rackmount UPS; Battery Replacement Instructions

MAINTENANCE 26 OBTAINING SERVICE 27 1. Use the TROUBLESHOOTING section to eliminate obvious causes. 2. Verify there are no circuit breakers tripped. A tripped circuit breaker is the most common problem. 3. Please have the following information available BEFORE calling the Technical Support departmen...