Belkin belkin bulldog plus- shutdown management software for windows - Manuals

Bulldog Plus Service Belkin Bulldog Service runs in the background as a Windows Service when the system initiates. You can also run Bulldog Service manually by selecting the Start Menu- Program Files - Belkin Bulldog - Bulldog Service. Once Bulldog Service starts there is a Bulldog Service icon loca...

Bulldog Plus Monitor Bulldog Monitor enables you to control and configure Bulldog Plus through drop down menus and dialog boxes. It also allows you to monitor the UPS through the Main Screen. It is not necessary for Bulldog Monitor to reside in your computer’s memory, the execution depends on the us...

Networking BULLDOG Plus software is comprised of two modules: BULLDOG Service and BULLDOG Monitor . You may run both the programs in a computer to monitor your localized UPS or run the programs in two different computers. Operation Mode: BULLDOG Service can operate in "Master" Mode (which al...

You can run only Bulldog Monitor without running Bulldog Service. Bulldog Monitor will search hosts in the LAN(Local Area Network) which runs Bulldog Service in the combo box. Click on the Host Selection combo box to list the searched hosts in the LAN. Select one, then Bulldog Monitor will connect t...

Bulldog Plus Monitor Operations The Main Screen has 7 areas that present information on the operating status of your UPS. These areas are discussed in the following sections. Host Selection : Press the combo box to select hosts that runs Bulldog Plus in the LAN. Users can monitor or control the UPS ...

Event Log: Same as the View-> Event Log in the menu. History Graph: Same as the View-> History Graph in the menu. Bulldog Monitor Main Menu The Main Screen has a menu bar at the top with 5 main options: o System: This menu allows you to set the Bulldog Plus and computer parameters. o Control: ...

System The system menu allows you to configure the UPS and the monitoring screen parameters. When you select the System menu from Main Menu bar, a drop down menu appears offering you the following menu options: Login : Used for Remote Monitor. User must enter the password verification before he can ...

Close Monitor Close Bulldog Monitor and leave Bulldog Service running. Belkin Components 18

Configuration The Configuration Screen has a menu bar at the top with three main options: Devices : This menu allows you to configure the modem, pager and e-mail applications. UPS : The UPS menu allows you to plan and set the UPS schedule or perform the Action... Network : This menu allows you to ch...

Bulldog Service Mode: Bulldog Service acts as a Master or Slave. Remote Host IP: The host, which runs Bulldog Service. If Bulldog Monitor and Bulldog Service runs on the same computer and this field will be empty. Belkin Components 20

Devices Notification Users -- Pager List Program will set the modem to notify all via the pager numbers, which are listed in the pager list. You can input your pager number for your own notification purposes. For example: 060123456 is your pager number, each ',' tells modem to delay 2 seconds, delay...

a. Color Items: This area lets you select an item, which you want to change the color for. The right-top corner will display the current selected color. b. Change: Change the color you have selected. c. Default: Default setting. d. Exit: Close the dialog box. Close Close the Configuration window. Be...

UPS UPS Property This dialog box allows you to configure the UPS COM port, battery replacement date, ... etc. Load Warning and Load Severity used to prevent UPS overload (see the UPS hardware user manual). In general, Load Warning will notify the user to reduce the UPS load, Load Severity will shutd...

Group2 is called Computer for association with the CPU. These records can improve the efficiency of your management. Don't forget to press the Update button. c. Update: Updates your change. Log Management: (Please consider the free space in your hard disk) a. Maximum Event Log Entries: Always Bulldo...

Action The action menu provides you with a list of events to choose from. The event and/or any combination of these actions can be selected from the Choose Event list box. Actions that are already enabled will show a check mark. To delay the actions, set the desired time for delay in the Delay combo...

Advanced UPS Property If your UPS doesn't support this function, the item will be displayed as gray and the user cannot select this item. Enable Wakeup Computer: If your computer architecture is compatible to ATX and the BIOS supports RS-232(RI) Wakeup function. You should enable this item to make t...

Network Set Password Sets the Bulldog Service password. Choose Master/Slave Please refer to the BULLDOG Service operation mode. If the computer connects to UPS directly (with RS-232 or USB) and can send commands to its connected UPS then the BULLDOG Service acts as a "Master". If it connects...

Wake On LAN To wake up the remote host, Bulldog Plus sends notification through the network. You must provide the IP address and the network hardware address of the remote host. In Windows98, you can execute the "ipconfig /All" command under the MS-DOS prompt to obtain the network cards phys...

SNMP If you are using a Windows 95/98/Me operating system, you can configure the SNMP parameters directly from the Bulldog Plus: Select the Accept SNMP packet from any hosts, Bulldog Plus will accept all the requested commands and set commands. When you select the Accept SNMP packet from the followi...

DupsEnvOverHumidity 34 WARNING: The environment over normal humidity DupsNoLongerEnvOverHumidity 35 INFORMATION: The environment recovered from abnormal humidity HTTP Bulldog Plus supports WEB Server for remote management and to obtain the UPS information. Users can use IE or Communicator to connect...

Control Shutdown Now This command will execute the shutdown procedure at once. a. Restart: This function lets you restart the UPS automatically after being shutdown. To start the UPS for the next schedule, mark the Restart check box. b. Shutdown OS and UPS: Use this function to shutdown both the OS ...

View Meters Bulldog Plus supports up to 12 meters of real-time values. Each meter has the ability to display all of the UPS values. Selecting different items from the Selection dialog box will display the selected item value. a. 2,4,6,8,12: Displays meter number. b. Selection: Assigns each meter to ...

a. Print: Prints the event log. b. Exit: Closes event log dialog box. History Graph Clicking on the History Graph opens a dialog box that contains information about the UPS data in graphical format. This information is available only if there is an accumulation of data. You can select the month and ...

a. Horizontal Scale: Selects the time scale. b. Vertical Scale: Selects the value scale. c. Select Month: Displays the UPS data for the month, which you want to see. d. Draw Item1(Blue): Displays the UPS item value by a blue line. e. Draw Item2(Red): Displays the UPS item value by a red line. f. Upd...

put the files in temporary directory. This dialog box will tell you which files were saved by Bulldog Plus. a. Program Title: The application’s title name. b. Auto-Save File Name: Bulldog Plus names the file for you. c. Clear: Clear this record. Remote Hosts Detects the hosts, which are running the ...

Bottom Layer Buttons Each button shows the respective information in the Information Area Main: General Information about the UPS. Tree: There are 2 sub-trees in the Bulldog Plus tree: System and UPS. The system tree is for host information and the status of Master/Slave connection, the UPS tree is ...

Service and Support Corporate Headquarters Belkin Corporation 501 West Walnut Street Compton • CA • 90220-5221 • USA Tel: 310.898.1100 Fax: 310.898.1111 Customer Service/Sales: 800.2BELKIN 800.223.5546 Technical Support: 310.898.1100 ext. 2263 800.223.5546 ext. 2263 Fax: 310.604.2089 techsupp@belkin...