B&B Electronics UNO-2170 - Manuals

Contents Chapter 1 Overview ...........................................................2 1.1 Introduction ....................................................................... 2 1.2 Hardware Specifications ................................................... 3 1.3 Safety Precautions ..................

Figure 3.1:Chassis Grounding Connection ................... 18 3.3 Connecting Power ........................................................... 19 3.4 Installing a Hard Disk ..................................................... 19 3.5 BIOS Setup and System Assignments ............................ 19...

1 2 Overview This chapter provides an overview of UNO-2170s specifications. Sections include: • Introduction • Hardware specification • Safety precautions • Chassis dimensions

Chapter 1 Overview 1.1 Introduction UNO-2170 is an embedded Application Ready Platform (ARP) that can shorten your development time and offers rich networking interfaces to fulfill extensive needs in different projects. Advantech Universal Net- work Controller is designed to be a total solution for ...

1.2 Hardware Specifications CPU: Up to Celeron-M 1GHz Ultra low-voltage version Memory: 256/512 MB DDR on board (Default: 256 MB DDR). Battery-backup RAM: 512 KB Battery-backup RAM VGA/Keyboard/Mouse: DB-15 VGA Connector, PS/2 keyboard and mouse Serial Ports: 2 x RS-232 and 2 x RS-232/422/485 with D...

1.3 Safety Precautions The following sections tell how to make each connection. In most cases, you will simply need to connect a standard cable. Warning! Always disconnect the power cord from your chassis whenever you are working on it. Do not connect while the power is on. A sudden rush of power ca...

1.4 Chassis Dimensions Figure 1.1: Chassis Dimensions 5 Chapter 1

2 2 Hardware Functionality This chapter shows how to setup the UNO-2170s hardware functions, including connecting peripherals, setting switches and indicators. Sections include: • Peripherals • RS-232 Interface • RS-232/422/485 Interface • LAN / Ethernet Connector • Power Connector • PS/2 Mouse and ...

Chapter 2 Hardware Functionality 2.1 Introduction The following two figures show the connectors on UNO-2170. The following sections give you detailed information about function of each peripheral. Figure 2.1: Front panel of UNO-2170 Figure 2.2: Rear panel of UNO-2170 2.2 RS-232 Interface (COM1~COM2)...

2.3 RS-232/422/485 Interface (COM3~COM4) The UNO-2170 offers two RS-232/422/485 serial communication interface ports: COM3 and COM4. Please refer to Appendix A.4 for their pin assignments. The default setting of COM3 and COM4 are RS-422/485. 2.3.1 16C550 UARTs with 16-byte standard Advantech UNO-217...

2.3.5 RS-232/422/485 Selection COM3 and COM4 support 9-wire RS-232, RS-422 and RS-485 inter faces. The system detects RS-422 or RS-485 signals automatically in RS- 422/485 mode. To select between RS-422/485 and RS-232 for COM3, adjust JP4. To select between RS-422/485 and RS-232 for COM4, adjust JP5...

2.3.6 RS-485 Auto Flow Control Mode and RS-422 Master/Slave Mode Selection You can set the “Auto Flow Control mode of RS-485 or “Master/Slave ＂ mode of RS-422 by using the SW3 DIP switch for each RS-422/485 port. In RS-485, if the switch is set to “Auto ＂ the driver automatically senses the directio...

2.3.7 IRQ and Address Setting The IRQ and I/O address range of COM3 and COM4 are listed below: COM3: 3E8H, IRQ10 (Independent IRQ), IRQ10 (Share IRQ) COM4: 2E8H, IRQ5 (Independent IRQ), IRQ10 (Share IRQ) Vector address for share IRQ: 1D0H You can set “Share IRQ ＂ or “Independent IRQ ＂ by the first s...

2.4 LAN: Ethernet Connector The UNO-2170 is equipped with a Realtek RTL8139C Ethernet LAN controller that is fully compliant with IEEE 802.3u 10/100Base-T CSMA/CD standards. The Ethernet port provides a standard RJ-45 jack on board, and LED indicators on the front side to show its Link (Green LED) a...

2.8 PCMCIA: PC Card Slot The UNO-2170 provides one PC Card slot that supports CardBus (Card- 32) cards and 16-bit (PCMCIA 2.1/JEIDA 4.2) card standards. It supports +3.3 V, +5 V and +12 V @ 120 mA working voltage. The PC Card is 85.6 mm long by 54 mm wide (3.37" x 2.126"), use a 68-pin conne...

2.10 Battery Backup SRAM UNO-2170 provides 512 KB of battery backed SRAM. This ensures that you have a safe place to store critical data. You can now write software applications without being concerned that system crashes will erase criti- cal data from the memory. There is a BTRY LED in the front p...

3 2 Initial Setup This chapter introduces how to initialize the UNO-2170. Sections include: • Introduction • Inserting a CompactFlash™ Card • Chassis Grounding • Connecting Power • Connecting a Hard Disk • BIOS Setup and System Assignments

Chapter 3 Initial Setup 3.1 Inserting a CompactFlash Card The procedure for installing a CompactFlash™ card into the UNO-2170 is detailed below, please follow these steps carefully. 1. Remove the power cord. 2. Unscrew the four screws from the rear panel of the UNO-2170. 3. Remove the rear panel. 4....

You can select if you wish to combine the chassis grounding point with the system grounding by using an onboard jumper selection. (JP7) Open - Separates system power ground and chassis ground. (default) Closed - Connects system power ground and chassis ground. 3.3 Connecting Power Connect the UNO-21...

Appendix A System Settings and Pin Assignments A.1 System I/O Address and Interrupt Assignment Table A.1: UNO-2170 System I/O Ports Address Range Device 000-01F DMA controller (slave) 020-03F Interrupt controller 1, (master) 040-05F 8254 timer/counter 060-06F 8042 (keyboard controller) 070-07F Real-...

Table A.1: UNO-2170 System I/O Ports Address Range Device 3D0-3DF Color/graphics monitor adapter 3F0-3F7 Diskette controller 3E8-3EF Serial port 3 3F8-3FF Serial port 1 443 Watchdog timer DC000-DFFFF Battery backup resource Table A.2: UNO-2170 Interrupt Assignment Interrupt No. Interrupt Source NMI ...

A.2 Board Connectors and Jumpers There are several connectors and jumpers on the UNO-2170 board. The following sections tell you how to configure the UNO-2170 hardware setting. Figure A-1 and Figure A-2 show the locations of UNO-2170’s connectors and jumpers. Figure A.1: UNO-2170 connector and jumpe...

Table A.3: UNO-2170 Connectors and Jumpers Label Function CN1 Phoenix power connector CN2 Ethernet port 1 CN5 Ethernet port 2 CN3 COM1 RS-232 serial port CN4 COM2 RS-232 serial port CN14 COM3 RS-232/422/485 serial port CN15 COM4 RS-232/422/485 serial port CN6 USB connector CN7 PS/2 keyboard and mous...

A.3 RS-232 Standard Serial Port (COM1~COM2) Table A.4: RS-232 standard serial port pin assignments Pin RS-232 Signal Name 1 DCD 2 RxD 3 TxD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI UNO-2170 User Manual 26

A.4 RS-232/422/485 Serial Port (COM3~COM4) Table A.5: RS-232/422/485 serial port pin assignments Pin RS-232 RS-422 RS-485 1 DCD Tx- DATA- 2 RxD Tx+ DATA+ 3 TxD Rx+ NC 4 DTR Rx- NC 5 GND GND GND 6 DSR NC NC 7 RTS NC NC 8 CTS NC NC 9 RI NC NC A.5 Ethernet RJ-45 Connector (LAN1~LAN2) Table A.6: Table A...

A.6 Phoenix Power Connector (PWR) Table A.7: Power connector pin assignments Pin 10/100Base-T Signal Name 1 +9~36VDC 2 GND A.7 PS/2 Keyboard and Mouse Connector Table A.8: Keyboard and Mouse connector pin assignments Pin Signal Name 1 KB DATA 2 MS DATA 3 GND 4 VCC 5 KB Clock 6 MS Clock UNO-2170 User...

A.8 USB Connector (USB1~USB2) Table A.9: USB connector pin assignments Pin Signal Name Cable Color 1 VCC Red 2 DATA+ White 3 DATA- Green 4 GND Black A.9 VGA Display Connector Table A.10: Table A-9: VGA adaptor cable pin assignment Pin Signal Name 1 Red 2 Green 3 Blue 4 NC 5 GND 6 GND 7 GND 8 GND 9 N...

Appendix B Programming the Watchdog Timer Bellow is a sample of programming code for controlling the Watchdog Timer function. ----------------------------------------------------------------------------------- Enter the extended function mode, interruptible double-write | ---------------------------...