Page 2 - Intel and Pentium are trademarks of Intel Corporation.; Support; st Edition, Printed in Taiwan Oct. 2005; UNO-2170 User Manual ii
Copyright This document is copyrighted, © 2004. All rights are reserved. The origi- nal manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmit- ted in any form ...
Page 3 - Product Warranty; product, and any helpful information readily available.; iii
Product Warranty Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for one year from the date of purchase. This warranty does not apply to any products that have been repaired or altered by persons other than repair pe...
Page 4 - UNO-2170 User Manual iv
Page 5 - Contents; v Table of Contents
Contents Chapter 1 Overview ...........................................................2 1.1 Introduction ....................................................................... 2 1.2 Hardware Specifications ................................................... 3 1.3 Safety Precautions ..................
Page 6 - UNO-2170 User Manual vi
Figure 3.1:Chassis Grounding Connection ................... 18 3.3 Connecting Power ........................................................... 19 3.4 Installing a Hard Disk ..................................................... 19 3.5 BIOS Setup and System Assignments ............................ 19...
Page 7 - Overview; Introduction
1 2 Overview This chapter provides an overview of UNO-2170s specifications. Sections include: • Introduction • Hardware specification • Safety precautions • Chassis dimensions
Page 8 - Chapter 1 Overview; UNO-2170 User Manual 2
Chapter 1 Overview 1.1 Introduction UNO-2170 is an embedded Application Ready Platform (ARP) that can shorten your development time and offers rich networking interfaces to fulfill extensive needs in different projects. Advantech Universal Net- work Controller is designed to be a total solution for ...
Page 9 - Hardware Specifications; Operating temperature:; Chapter 1
1.2 Hardware Specifications CPU: Up to Celeron-M 1GHz Ultra low-voltage version Memory: 256/512 MB DDR on board (Default: 256 MB DDR). Battery-backup RAM: 512 KB Battery-backup RAM VGA/Keyboard/Mouse: DB-15 VGA Connector, PS/2 keyboard and mouse Serial Ports: 2 x RS-232 and 2 x RS-232/422/485 with D...
Page 10 - Safety Precautions; Warning! Always disconnect the power cord from your chassis; UNO-2170 User Manual 4
1.3 Safety Precautions The following sections tell how to make each connection. In most cases, you will simply need to connect a standard cable. Warning! Always disconnect the power cord from your chassis whenever you are working on it. Do not connect while the power is on. A sudden rush of power ca...
Page 11 - Chassis Dimensions; Chapter 1
1.4 Chassis Dimensions Figure 1.1: Chassis Dimensions 5 Chapter 1
Page 12 - UNO-2170 User Manual 6
Page 13 - Hardware Functionality
2 2 Hardware Functionality This chapter shows how to setup the UNO-2170s hardware functions, including connecting peripherals, setting switches and indicators. Sections include: • Peripherals • RS-232 Interface • RS-232/422/485 Interface • LAN / Ethernet Connector • Power Connector • PS/2 Mouse and ...
Page 14 - Chapter 2 Hardware Functionality; IRQ and Address Setting; UNO-2170 User Manual 8
Chapter 2 Hardware Functionality 2.1 Introduction The following two figures show the connectors on UNO-2170. The following sections give you detailed information about function of each peripheral. Figure 2.1: Front panel of UNO-2170 Figure 2.2: Rear panel of UNO-2170 2.2 RS-232 Interface (COM1~COM2)...
Page 15 - Chapter 2
2.3 RS-232/422/485 Interface (COM3~COM4) The UNO-2170 offers two RS-232/422/485 serial communication interface ports: COM3 and COM4. Please refer to Appendix A.4 for their pin assignments. The default setting of COM3 and COM4 are RS-422/485. 2.3.1 16C550 UARTs with 16-byte standard Advantech UNO-217...
Page 16 - UNO-2170 User Manual 10
2.3.5 RS-232/422/485 Selection COM3 and COM4 support 9-wire RS-232, RS-422 and RS-485 inter faces. The system detects RS-422 or RS-485 signals automatically in RS- 422/485 mode. To select between RS-422/485 and RS-232 for COM3, adjust JP4. To select between RS-422/485 and RS-232 for COM4, adjust JP5...
Page 17 - 1 Chapter 2
2.3.6 RS-485 Auto Flow Control Mode and RS-422 Master/Slave Mode Selection You can set the “Auto Flow Control mode of RS-485 or “Master/Slave ＂ mode of RS-422 by using the SW3 DIP switch for each RS-422/485 port. In RS-485, if the switch is set to “Auto ＂ the driver automatically senses the directio...
Page 18 - Vector address for share IRQ:; You can set “Share IRQ; Function; Independent IRQ; Switch 2 at SW4 setting; UNO-2170 User Manual 12
2.3.7 IRQ and Address Setting The IRQ and I/O address range of COM3 and COM4 are listed below: COM3: 3E8H, IRQ10 (Independent IRQ), IRQ10 (Share IRQ) COM4: 2E8H, IRQ5 (Independent IRQ), IRQ10 (Share IRQ) Vector address for share IRQ: 1D0H You can set “Share IRQ ＂ or “Independent IRQ ＂ by the first s...
Page 19 - 3 Chapter 2
2.4 LAN: Ethernet Connector The UNO-2170 is equipped with a Realtek RTL8139C Ethernet LAN controller that is fully compliant with IEEE 802.3u 10/100Base-T CSMA/CD standards. The Ethernet port provides a standard RJ-45 jack on board, and LED indicators on the front side to show its Link (Green LED) a...
Page 20 - PS: PCMCIA interrupt assignment is IRQ 9.; VGA Display Connector; UNO-2170 User Manual 14
2.8 PCMCIA: PC Card Slot The UNO-2170 provides one PC Card slot that supports CardBus (Card- 32) cards and 16-bit (PCMCIA 2.1/JEIDA 4.2) card standards. It supports +3.3 V, +5 V and +12 V @ 120 mA working voltage. The PC Card is 85.6 mm long by 54 mm wide (3.37" x 2.126"), use a 68-pin conne...
Page 21 - Battery Backup SRAM; Figure 2.5: The location of the lithium battery for SRAM; 5 Chapter 2
2.10 Battery Backup SRAM UNO-2170 provides 512 KB of battery backed SRAM. This ensures that you have a safe place to store critical data. You can now write software applications without being concerned that system crashes will erase criti- cal data from the memory. There is a BTRY LED in the front p...
Page 22 - UNO-2170 User Manual 16
Page 23 - Initial Setup
3 2 Initial Setup This chapter introduces how to initialize the UNO-2170. Sections include: • Introduction • Inserting a CompactFlash™ Card • Chassis Grounding • Connecting Power • Connecting a Hard Disk • BIOS Setup and System Assignments
Page 24 - Chapter 3 Initial Setup; Inserting a CompactFlash Card; Unscrew the four screws from the rear panel of the UNO-2170.; Chassis Grounding; UNO-2170 User Manual 18
Chapter 3 Initial Setup 3.1 Inserting a CompactFlash Card The procedure for installing a CompactFlash™ card into the UNO-2170 is detailed below, please follow these steps carefully. 1. Remove the power cord. 2. Unscrew the four screws from the rear panel of the UNO-2170. 3. Remove the rear panel. 4....
Page 25 - Screw back the rear panel with the four screws.; BIOS Setup and System Assignments; Please note that you can try to “LOAD BIOS DEFAULTS; 9 Chapter 3
You can select if you wish to combine the chassis grounding point with the system grounding by using an onboard jumper selection. (JP7) Open - Separates system power ground and chassis ground. (default) Closed - Connects system power ground and chassis ground. 3.3 Connecting Power Connect the UNO-21...
Page 26 - UNO-2170 User Manual 20
Page 28 - A.1 System I/O Address and Interrupt Assignment; Address Range Device; UNO-2170 User Manual 22
Appendix A System Settings and Pin Assignments A.1 System I/O Address and Interrupt Assignment Table A.1: UNO-2170 System I/O Ports Address Range Device 000-01F DMA controller (slave) 020-03F Interrupt controller 1, (master) 040-05F 8254 timer/counter 060-06F 8042 (keyboard controller) 070-07F Real-...
Page 29 - 3 Appendix A
Table A.1: UNO-2170 System I/O Ports Address Range Device 3D0-3DF Color/graphics monitor adapter 3F0-3F7 Diskette controller 3E8-3EF Serial port 3 3F8-3FF Serial port 1 443 Watchdog timer DC000-DFFFF Battery backup resource Table A.2: UNO-2170 Interrupt Assignment Interrupt No. Interrupt Source NMI ...
Page 30 - A.2 Board Connectors and Jumpers; UNO-2170 User Manual 24
A.2 Board Connectors and Jumpers There are several connectors and jumpers on the UNO-2170 board. The following sections tell you how to configure the UNO-2170 hardware setting. Figure A-1 and Figure A-2 show the locations of UNO-2170’s connectors and jumpers. Figure A.1: UNO-2170 connector and jumpe...
Page 31 - 5 Appendix A
Table A.3: UNO-2170 Connectors and Jumpers Label Function CN1 Phoenix power connector CN2 Ethernet port 1 CN5 Ethernet port 2 CN3 COM1 RS-232 serial port CN4 COM2 RS-232 serial port CN14 COM3 RS-232/422/485 serial port CN15 COM4 RS-232/422/485 serial port CN6 USB connector CN7 PS/2 keyboard and mous...
Page 32 - Pin RS-232 Signal Name; UNO-2170 User Manual 26
A.3 RS-232 Standard Serial Port (COM1~COM2) Table A.4: RS-232 standard serial port pin assignments Pin RS-232 Signal Name 1 DCD 2 RxD 3 TxD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI UNO-2170 User Manual 26
Page 33 - 7 Appendix A
A.4 RS-232/422/485 Serial Port (COM3~COM4) Table A.5: RS-232/422/485 serial port pin assignments Pin RS-232 RS-422 RS-485 1 DCD Tx- DATA- 2 RxD Tx+ DATA+ 3 TxD Rx+ NC 4 DTR Rx- NC 5 GND GND GND 6 DSR NC NC 7 RTS NC NC 8 CTS NC NC 9 RI NC NC A.5 Ethernet RJ-45 Connector (LAN1~LAN2) Table A.6: Table A...
Page 34 - Table A.7: Power connector pin assignments; Pin 10/100Base-T Signal Name; Table A.8: Keyboard and Mouse connector pin assignments; Pin Signal Name; UNO-2170 User Manual 28
A.6 Phoenix Power Connector (PWR) Table A.7: Power connector pin assignments Pin 10/100Base-T Signal Name 1 +9~36VDC 2 GND A.7 PS/2 Keyboard and Mouse Connector Table A.8: Keyboard and Mouse connector pin assignments Pin Signal Name 1 KB DATA 2 MS DATA 3 GND 4 VCC 5 KB Clock 6 MS Clock UNO-2170 User...
Page 35 - Pin Signal Name Cable Color; A.9 VGA Display Connector; 9 Appendix A
A.8 USB Connector (USB1~USB2) Table A.9: USB connector pin assignments Pin Signal Name Cable Color 1 VCC Red 2 DATA+ White 3 DATA- Green 4 GND Black A.9 VGA Display Connector Table A.10: Table A-9: VGA adaptor cable pin assignment Pin Signal Name 1 Red 2 Green 3 Blue 4 NC 5 GND 6 GND 7 GND 8 GND 9 N...
Page 36 - UNO-2170 User Manual 30
Page 38 - Appendix B Programming the Watchdog Timer; UNO-2170 User Manual 32
Appendix B Programming the Watchdog Timer Bellow is a sample of programming code for controlling the Watchdog Timer function. ----------------------------------------------------------------------------------- Enter the extended function mode, interruptible double-write | ---------------------------...
Page 39 - 3 Appendix B
Page 40 - UNO-2170 User Manual 34
