Barco R9001280 - Manuals - manualsarea.com

Page 3 - BARCO PROJECTION SYSTEMS; VISION

BARCO PROJECTION SYSTEMS Date :280497 Art. No. : R5975348 R9001280 OWNER'S MANUAL VISION 8200 Rev :01

Page 4 - Printed in Belgium

Due to constant research, the information in this manual is subject to change without notice. Produced by BARCO NV, April 1997.All rights reserved. Trademarks are the rights of their respective owners. Printed in Belgium BARCO nv/Projection SystemsNoordlaan 5B-8520 KuurneBelgium Printed in Belgium

Page 5 - Table of Contents; TABLE OF CONTENTS

Table of Contents i-1 5975348 BARCOVISION 8200 210497 TABLE OF CONTENTS i TABLE OF CONTENTS ................................................................................................................................................................... i-1 SAFETY INSTRUCTIONS .......................

Page 7 - Safety Instructions; SAFETY INSTRUCTIONS; Installation instructions; OWNER’S RECORD; Federal communication commission (FCC statement)

Safety Instructions 1-1 5975348 BARCOVISION 8200 210497 1 SAFETY INSTRUCTIONS Projectors are built in accordance with the requirements of theinternational safety standards IEC950, UL 1950 and CSA C22.2 No.950, which are the safety standards of information technology equip-ment including electrical b...

Page 8 - Remarque sur la Sécurité; DONNEES POUR LE PROPRIETAIRE; AVERTISSEMENT; ATTENTION; Fédéral communication commission (FCC statement)

Safety Instructions 1-2 5975348 BARCOVISION 8200 210497 Remarque sur la Sécurité Les projecteurs sont fabriqués conformément aux exigences desnormes de sécurité internationales IEC950, UL 1950 et CSA C22.2No. 950. Ces normes de sécurité sont imposées aux équipements dela technologie informatique inc...

Page 9 - On Installation

Safety Instructions 1-3 5975348 BARCOVISION 8200 210497 * Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. * To disconnect the cord, pull it out by the plug. Never pull the cord itself. * If an extension cord is used with this product, ...

Page 10 - L’Installation

Safety Instructions 1-4 5975348 BARCOVISION 8200 210497 * Ne rien laisser en appui sur le cordon d’alimentation. Ne pas placer ce cordon là où des personnes risques de marcher dessus. * Pour débrancher le cordon, le tirer par le connecteur, jamais par le cordon lui-même. * Si on utilise une rallonge...

Page 11 - Unpacking and Dimensions; UNPACKING AND DIMENSIONS; Unpacking; allow air circulation via the built-in dust filter at the bottom.; Projector dimensions; P u l l

Unpacking and Dimensions 2-1 5975348 BARCOVISION 8200 210497 L 2 UNPACKING AND DIMENSIONS Unpacking To open the banding, pull on the clip as shown in the first drawing. Take the projector out of its shipping carton and place it on a table.For transportation, the projector is mounted on a wooden boar...

Page 12 - Battery

Unpacking and Dimensions 2-2 5975348 BARCOVISION 8200 210497 Battery installation in the RCU. A battery (not yet installed to save the battery life time) is delivered inside the plastic bag with the powercord. To install the battery, remove the battery cover on the backside of the remote control by ...

Page 13 - Installation Guidelines; INSTALLATION GUIDELINES; Installation guidelines

Installation Guidelines 3-1 5975348 BARCOVISION 8200 210497 3 INSTALLATION GUIDELINES Screen width Installation guidelines Careful consideration of things as image size, ambient light level,projector placement and type of screen to use are critical to theoptimum use of the projection system.Max. amb...

Page 14 - Definitions of the Abbreviation on drawings; How to install the lens?

Installation Guidelines 3-2 5975348 BARCOVISION 8200 210497 * Where to install the projector? Definitions of the Abbreviation on drawings B = Distance between ceiling and top of the screen orbetween floor and bottom of the screen. A = Correction value, distance between bottom side of projec-tor (wit...

Page 15 - Location and Functions of Control; LOCATION AND FUNCTIONS OF CONTROL; Front panel terminology; Power input : autoranging from 100 to 240 Vac.; green lighting up : projector in operational mode.; Control Panel Terminology; Gaining access

Location and Functions of Control 4-1 5975348 BARCOVISION 8200 210497 4 LOCATION AND FUNCTIONS OF CONTROL Front panel terminology RS 232 IN REMOTE PROJECTOR MODE : GREEN - OPERATION RED - STANDBY COMMUNICATION PORT (800-PERIPHERALS) RS232 OUT 0 I Th is d evi ce c ompl ies wit h P art 15 o f t he F C...

Page 16 - Terminology

Location and Functions of Control 4-2 5975348 BARCOVISION 8200 210497 b. Remote control This remote control includes a battery powered infrared (IR) transmit-ter that allows the user to control the projector remotely.This remote control is used for source selection, control, adaptationand set up. It...

Page 17 - Installation Set Up; INSTALLATION SET UP; ENTER

Installation Set Up 5-1 5975348 BARCOVISION 8200 210497 5 INSTALLATION SET UP The projector can be installed to project images in four differentconfigurations : front/table, front/ceiling, rear/table and rear/ceiling. Front/Table Front/Ceiling Rear/Table Rear/Ceiling When switching on and the projec...

Page 18 - SYSTEM SETTINGS

Installation Set Up 5-2 5975348 BARCOVISION 8200 210497 Push the control disk up or down to highlight Systems Settings and press ENTER. ENTER displays the System Settings menu. EXIT returns to operational mode. Push the control disk up or down to highlight Installation and press ENTER . SYSTEM SETTI...

Page 19 - Connections; CONNECTIONS; Fuses; Stand by button; Switching on; Use the power switch to switch on.; Projector mode indication

Connections 6-1 5975348 BARCOVISION 8200 280497 6 CONNECTIONS R S232 OUT I R - AC K N O W L ED G E D I R- R EC E I VE D DI AG NOS TI CS C OD E I R- R EC E I VE R 10 0 - 230 V 9 - 4 A 60 - 50 Hz 0 I Th is d e vice co mplie s with Par t 1 5 o f th e FC C ru le s. Op e r atio n is su bje ct to follo w ...

Page 20 - Switching off; STANDBY; WARNING

Connections 6-2 5975348 BARCOVISION 8200 280497 When the total run time of the lamp is 970 hours or more, the following message will bedisplayed for 1 minute. This message will be repeated every 30 minutes. Press EXIT toremove the message before the minute is over. When the total run time of the lam...

Page 21 - On; MAIN MENU; INPUT SLOTS

Connections 6-3 5975348 BARCOVISION 8200 280497 Video/S-video input module To the Video input : Composite video signals from a VCR, OFF air signal decoder, etc...1 x BNC 1.0Vpp ± 3 dB To the S-Video input : Separate Y-luma/C-chroma signals for higher quality playback ofSuper VHS-signals. VIDEO/S-VID...

Page 22 - RGB input selection :

Connections 6-4 5975348 BARCOVISION 8200 280497 RGB analog input module. RGB analog input terminals with separate Horizontal and Verticalsync inputs(RGB-HV), with Composite sync input(RGB-S) or withSync signals on green(RGsB). Always use an interface when a computer and local monitor have tobe conne...

Page 23 - System Settings; Component input module.; COMPONENT VIDEO INPUT; Component input selection :

Connections 6-5 5975348 BARCOVISION 8200 280497 Push the control disk key up or down to select System Settings and press ENTER . Use the control disk to select Input Slots by pushing up or down andpress ENTER . The internal system will scan the inputs and displays the result in the Input Slots menu....

Page 24 - Straps on module level :; Vpp ± 3 dB if Tri-level sync on green; Blue; Indication on the input slot menu :

Connections 6-6 5975348 BARCOVISION 8200 280497 Straps on module level : Floating or non-floating input.R-Y : J3 : strap "yes" : non floating strap "no" : floating Y : J4 : strap "yes" : non floating strap "no" : floating B-Y : J5 : strap "yes" : non floating ...

Page 25 - Applications : remote control and VISION communications.

Connections 6-7 5975348 BARCOVISION 8200 280497 Straps on module level : Floating or non-floating input.Red : J3 : strap "yes" : non floating strap "no" : floating Green : J4 : strap "yes" : non floating strap "no" : floating Blue : J5 : strap "yes" : non floa...

Page 26 - Processor module; Connecting a RCVDS 05 to the projector.

Connections 6-8 5975348 BARCOVISION 8200 280497 Loosen the locking Open the top cover R B V R B V 10 0 - 23 0 V 9 - 4 A 6 0 - 50 Hz R S232 OU T 0 I Th is d e vice comp lie s with Pa r t 1 5 o f th e FC C r u le s. Op e ra tio nis su b je ct to fo llo w in g tw o con d itio n s : ( 1 ) Th is d e vice...

Page 27 - Controlling; CONTROLLING; The projector can be controlled with; Projector address; a. hardware set up of the projector address.

Controlling 7-1 5975348 BARCOVISION 8200 280497 7 CONTROLLING The projector can be controlled with a. The RCUb. The hardwired RCU (cable is not included)c. The local keypad. Controlling the projector with the RCU and the hardwired RCU isequal. How to use the RCU? a) Point the front of the RCU to the...

Page 28 - b. How to control the projector or projectors.; How to display a projector address?; How to program an address into the RCU?; ADDRESS; Picture controls with direct access.

Controlling 7-2 5975348 BARCOVISION 8200 280497 switch value 1 1 2 2 3 4 4 8 5 16 6 32 7 64 8 128 Example : address 83 DIP switch 1 2 3 4 5 6 7 8 setting 1 1 0 0 1 0 1 0 Summary : 1x1 + 1x2 + 0x4+ 0x8+ 1x16 + 0x32 + 1x64 + 0x128 = 83 b. How to control the projector or projectors. The projector's add...

Page 30 - SUMMARY

Controlling 7-4 5975348 BARCOVISION 8200 280497 How to get a summary of your projector? The Summary gives an overview of : - type of projector- soft version- lamp run time- projector run time- address- installation configuration- baud rate- projector serial number- lamp serial number To display the ...

Page 31 - Source Set Up; SOURCE SET UP; Input selection; Start up the adjustment mode by pressing; xxxXxxx : active pixel rating; to display the Load; LOAD FILE; FILE SERVICE

Source Set Up 8-1 5975348 BARCOVISION 8200 210497 8 SOURCE SET UP Input selection Use the numeric keys on the RCU or use the local key pad to select the corresponding inputslot.The source settings has to be installed for each source when these sources are displayed forthe first time. Installation of...

Page 32 - Edit file; Read only

Source Set Up 8-2 5975348 BARCOVISION 8200 210497 Push the control disk up or down to select the most fitting file and press ENTER to select. When scrolling through the files, the image will be adapted according the settings of theselected file (on line adaptation). When the best fitting image is di...

Page 33 - Vertical shift

Source Set Up 8-3 5975348 BARCOVISION 8200 210497 How finding the correct values for the displayed item? During the installation of a file with LOAD, the horizontal period, thetotal number of vertical lines and the interlaced mode are automati-cally measured and filled in in the menu table. These va...

Page 34 - Vertical sync polarity; Rename

Source Set Up 8-4 5975348 BARCOVISION 8200 210497 Vertical refresh [sync/async] : The way of updating the image information on the LCD panels.* For sources with a vertical frequency up to 60 Hz : the verticalrefresh rate is the same as the vertical frequency of the incomingsource. This is a necessit...

Page 35 - Options

Source Set Up 8-5 5975348 BARCOVISION 8200 210497 Move To move a selected file to the file with the name and extension givenin the TO area.Use the control disk to select MOVE and press ENTER . The move menu will be displayed. FILE SERVICE 847f LoadEditRenameCopy Move DeleteOptions MOVE FILE pal .s1 ...

Page 37 - Picture Control in Adjustment Mode; PICTURE CONTROL IN ADJUSTMENT MODE; The picture control menu is split up in two parts :; Signal operations; PICTURE CONTROL; SIGNAL OPERATIONS; Push the control disk up or down to select Signal Operations.; Video offset

Picture Control in Adjustment Mode 9-1 5975348 BARCOVISION 8200 210497 9 PICTURE CONTROL IN ADJUSTMENT MODE The picture control menu is split up in two parts : Signal operationsandScreen operations. Signal operations : to manipulate the video signal, e.g. sync slow/fast, color balance adjustment etc...

Page 38 - Gain adjustment per color; to toggle between ON and OFF.; to toggle between Slow and Fast.; Color Balance; to select the color balance selection menu.; A marker indicates the actual color balance setting.

Picture Control in Adjustment Mode 9-2 5975348 BARCOVISION 8200 210497 Gain adjustment per color If the obtained color balance is not yet correct, adjust with the separategain controls until the desired color balance is obtained. Smoothness The lower the smoothness value, the sharper the image. Thei...

Page 39 - Screen operations; SCREEN OPERATIONS

Picture Control in Adjustment Mode 9-3 5975348 BARCOVISION 8200 210497 Screen operations Select the Picture Control menu on the Main menu by pushing the control disk up or down. Press ENTER to select. Push the control disk up or down to select Screen operations . Press ENTER to select. When pushing ...

Page 40 - moves the window upwards

Picture Control in Adjustment Mode 9-4 5975348 BARCOVISION 8200 210497 870 870 [window] moves the window upwards 870 870 [window] moves the window downwards 870870 [window] stretches the window in thehorizontal direction. 870 870 [window] Compresses the window inthe horizontal direction. 870 870 [wi...

Page 41 - Picture; The picture can be moved, enlarged, reduced within a created window.

Picture Control in Adjustment Mode 9-5 5975348 BARCOVISION 8200 210497 870 870 [window] [window] reduces the window, both ofhorizontal and vertical direc-tions simultaneously. reset button, brings the windowto its maximum dimensions. Picture The picture can be moved, enlarged, reduced within a creat...

Page 43 - geometry; CONFIGURE; Conversion; tions; Geometry

Picture Control in Adjustment Mode 9-7 5975348 BARCOVISION 8200 210497 Configure The configure menu contains two toggle functions : geometry and conversion . Use the control disk to select Configure and press ENTER . SCREEN OPERATIONS 86 8b Zoom/ PanGeometry (off) Confi gur e Conversi on [On]Geometr...

Page 45 - SERVICE MODE; The service mode offers :; How to activate the password function?; Password; Start up of the Service mode.; When in operational mode, press ENTER to display the; Use the control disk to highlight; Service mode; If the password function is activated, the; Enter password

Service Mode 10-1 5975348 BARCOVISION 8200 210497 SERVICE MODE 10 The service mode offers : - test patterns such as convergence patterns (green, red on green, blue on green and hatch patterns). - alignments for the decoder circuit such as luminance delay, comb filter, etc. (more info in service manu...

Page 46 - Convergence adjustment of the LCD panels.; CONVERGENCE

Service Mode 10-2 5975348 BARCOVISION 8200 210497 Factory programmed password : 0000 SERVICE MODE Modi fy Passwor dReset Lamp Run TimeLamp Run Ti me Hi stor yConver genceDi splay SettingsDecoder Setti ngsCol or BalanceI2C Device Test 87 8 Convergence adjustment of the LCD panels. Every LCD panel has...

Page 47 - Green focusing

Service Mode 10-3 5975348 BARCOVISION 8200 210497 The pattern shows lines of one pixel.Near six lines on the displayed pattern, a screw is drawn with anumber next to it (e.g. if displayed in green = corresponding with thescrews and numbers on the green LCD panel).When turning a screw in the directio...

Page 48 - Test; Blue on green; display the Blue on green test pattern.; To check the result of the convergence adjustments, highlight; Hatch

Service Mode 10-4 5975348 BARCOVISION 8200 210497 Two possibilities : 1) distance between red lines is smaller than distance between green lines.Turn screw 5 and 6 clockwise until distance between lines 5 and6 is the same for the red and green lines. 2) distance between red lines is greater than dis...

Page 49 - Lamp Run Time History; Lamp; LAMP RUN TIME HISTORY; Reset Lamp Run Time

Service Mode 10-5 5975348 BARCOVISION 8200 210497 Modify password To change your password, highlight 'Modify password' and press ENTER to start up the password modification procedure.Enter your old password with the digit keys. After the fourth digit isentered, the next modify password menu is displ...

Page 50 - When; is selected in the

Service Mode 10-6 5975348 BARCOVISION 8200 210497 When Reset Lamp Run Time is selected in the Service Mode menu, the following warning will be displayed :Risk of electrical shock. Reset lamp run time is reserved to qualifiedservice personnel.If you are not qualified, press EXIT to cancel the reset o...

Page 51 - Standard Source Set Up Files; STANDARD SOURCE SET UP FILES; Standard source set up files.

Standard Source Set Up Files A-1 5975388 BARCOVISION 9200 210497 STANDARD SOURCE SET UP FILES A Standard source set up files. Standard preprogrammed set up files. NAME RESOLUTION FVERT FHOR FPIX PTOT PACT LTOT LACT Hz kHz MHz CGA 640 X 200 59,924 15,700 14,318 912 640 262 200 NTSC 675 X 240I 29,970 ...

Page 53 - Battery Replacement in the RCU; BATTERY REPLACEMENT IN THE RCU; Battery replacement in the RCU.

Battery Replacement in the RCU B - 1 5975348 BARCOVISION 8200 210497 BATTERY REPLACEMENT IN THE RCU B fig. 1 Battery replacement in the RCU. Remove the battery cover on the backside of the remote control bypushing the indicated handle a little to the bottom of the RCU. Lift upthe top side of the cov...

Page 54 - Lenses; LENSES; Focusing the lens; Cleaning procedure for the other HD lens

Lenses C-1 5975348 BARCOVISION 8200 210497 C LENSES Focusing the lens Loosen the fastener ring of the lens by turning counter clockwise. Focus the image by turning the lens barrel to the left or the right.Attention : Do not turn out the lens too far, otherwise it will fall out ofthe lens holder. Whe...

Page 55 - Lens formulas to calculate the projector distance.

Lenses C-2 5975348 BARCOVISION 8200 210497 Lenses This APPENDIX gives an overview of the tables and formulas for the available lenses for the projector. The next lenses are available : Name length lens diam. lens weight order number mm (inch) mm (inch) kg (lbs) HD(1.2:1) 253 (9.96) 189 (7.44) 8.7 (1...

Page 57 - RCU; INSERT CARD

Insert Card 5975348 BARCOVISION 8200 210497 P RCU INPUT SOURCES 1 PROJECTOR RCVDS 2 3 4 5 6 1 2 3 5 6 7 8 9 10 INPUT SOURCES 7 P RCU INPUT SOURCES 1 PROJECTOR RCVDS 2 3 4 5 6 1 2 3 5 6 7 8 9 10 INPUT SOURCES 7 " INSERT CARD