Barco II - Manual - manualsarea.com

Page 2 - User’s Guide Addendum; Copyright

26-0904001-00 Rev 00.00 2 User’s Guide Addendum Copyright © Barco. June 12, 2012 All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of Barco. Notice B...

Page 4 - Operators Safety Summary; Do Not Remove Covers or Panels

26-0904001-00 Rev 00.00 4 Operators Safety Summary The general safety information in this summary is for operating personnel. Do Not Remove Covers or Panels There are no user-serviceable parts within the unit. Removal of the top cover will expose dangerous voltages. To avoid personal injury, do not ...

Page 5 - Change History; Rev

26-0904001-00 Rev 00.00 5 Change History The table below lists the changes to the User’s Guide Addendum. Rev Date ECP # Description Approved By 00 6/22/12 597847 Initial Release R. Pellicano

Page 6 - Table of Contents

26-0904001-00 Rev 00.00 6 Table of Contents Introduction....................................................................... 7 1. Getting Started .............................................................. 7 2. Initial Setup ................................................................... 7...

Page 9 - Output Configuration

26-0904001-00 Rev 00.00 9 3. Output Configuration Once the mode and connectors have been setup, specific configuration of the two outputs can be performed. Output Resolution 1) In the OUTPUT setup menu, the first two lines (labelled CHA and CHB) show the current resolution and frame rate for each ch...

Page 10 - Freerun

26-0904001-00 Rev 00.00 10 Output Effects 1) Select the EFFECTS submenu under OUTPUT. 2) The first field (labelled CHANNEL) allows the selection of A, B or ALL to allow for independent or simultaneous adjustments for each output. Genlock 1) Select the GENLOCK submenu under OUTPUT. 2) The first field...

Page 12 - General Operation

26-0904001-00 Rev 00.00 12 4. General Operation 1) In addition to the input and output connectors provided in ImagePro-II, the ImagePro-II Dual output unit provides a second SDI input (SDI 6) and associated loop-through as well as a second SDI output (SDI 2 OUT). 2) When switching from Single mode t...

Page 13 - Remote Commands; ICH

26-0904001-00 Rev 00.00 13 5. Remote Commands The following commands have been updated as of software release 02.00.02. ICH Description: Input Channel Settings Required parameters: --con (connector) --ch (channel) --itype (input type), only for commands to DVI connector Parameters: --con (connector)...

Page 14 - IMGR

26-0904001-00 Rev 00.00 14 Query Format 2 (Input window): ICH --con (connector) --ch (channel) --iwin --? Query Response 2 : Input Channel Window Setting in the following format ICH --hpos (H Position) --vpos (V Position) --hsize (H Size) --vsize (V Size) Query Format 3 (Mask): ICH --con (connector)...

Page 16 - SYSMGR; UINPUT

26-0904001-00 Rev 00.00 16 SYSMGR Description: System Manager Settings Parameters: --blkinv (Black Invalid Mode) : 0=OFF, 1=ON --vfd (VFD Brightness) : 0..6 --opmode (Operation Mode) : 0=SingleChannel, 1=DualChannel, 2=3DProcessing Note: For the new operating take full effect, you must save settings...

Page 18 - VIEW

26-0904001-00 Rev 00.00 18 Parameters: --con (connector) : 0-5, see below for connector numbers. --och (output channel) : 0-1 --itype (input type) : 0 = digital, 1 = analog --brt (overall brightness) : [50..150] --cbrt (individual brightness) : [50..150] --cnt (overall contrast) : [50..150] --ccnt (...

Page 19 - VIDREF

26-0904001-00 Rev 00.00 19 --ch (channel) :0-1, input channel --units (units) :0 = percent, 1 = pixel --percent :if values are given in percent, See PANZOOM --help for parameter details --pixel :if values are given in pixel, See RECT --help for parameter details --save (save view settings) --recall ...

Barco II - Manual

Table of Contents:

Summary

Other Barco Models