Page 3 - Copyright notice
3 Copyright notice This document is copyrighted. All rights are reserved. Nor this document, nor any part of it, may be reproduced or copied in any form or by any means - graphical, electronic, or mechanical including photocopying, taping or information storage and retrieval systems - without writte...
Page 4 - Table of Contents
Table of Contents 4 Table of Contents Preface ................................................................................................. 5 Environmental information.......................................................... 7Safety Instructions.....................................................
Page 5 - Preface; Notice
Preface 5 Preface Notice Although every attempt has been made to achieve technical accuracy in this document, we assume no responsibility for errors that may be found. Our goal is to provide you with the most accurate and usable documentation possible; if you discover errors, please let us know. Bar...
Page 6 - Canadian notice
Preface 6 reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect th...
Page 7 - Environmental information; Disposal Information; Safety Instructions; General Recommendations
Preface 7 Environmental information Disposal Information The lamps inside the display contain mercury. Do not throw the display in the trash. Dispose of it as required by local ordinances or regulations. This equipment has required the extraction and use of natural resources for its production. It m...
Page 8 - Electrical shock
Preface 8 Electrical shock Type of protection (electrical): Class I equipment Degree of safety (flammable anesthetic mixture): Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide. Power connection • Power requirements: The display...
Page 9 - Water and moisture; Ventilation; Operating precautions
Preface 9 Water and moisture Never expose the display to rain or moisture. Never use the display near water - e.g. near a bathtub, washbasin, swimming pool, kitchen sink, laundry tub or in a wet basement. Ventilation Do not cover or block the ventilation openings in the cover of the set. When instal...
Page 10 - Overview; Introduction; Multi-scan capabilities
Overview 10 Overview Introduction The MFCD 1219 (TS), BARCO’s full color 19” LCD display, guarantees perfect image quality in medical imaging applications. The display combines a TFT (thin film transistor) liquid crystal display panel structure and a built-in backlight with inverter for a better pic...
Page 11 - Touch panel; Package contents
Overview 11 Touch panel The MFCD 1219 TS is equipped with a touch panel. Instructions on how to install and use the touch panel driver and controls can be found in the "TouchKit, Barco TouchScreen controller installation and user manual" on the supplied CD-ROM. Package contents The package s...
Page 12 - Controls and connectors
Overview 12 Controls and connectors 1. 12V DC power input 2. DVI input (DVI-D supported only) 3. Analog video input 4. USB port for touch panel connection to PC (MFCD 1219 TS only) 5. < (left) Key 6. > (right) Key 7. Menu key 8. Auto Key 9. Power LED The LED is off when the display is off. The...
Page 14 - Installation; Precautions; Wall mounting; Step 1: Remove the panel from the foot
Installation 14 Installation Precautions • Keep your original packaging. It is designed for this display and is the ideal protection during transport. • Avoid reflections in the flat panel to reduce eye strain.• Place the display on a strong and stable table or desk.• Keep the display away from heat...
Page 15 - Step 2: Fix the mounting plate to the wall
Installation 15 2. Firmly press down the push-button (9) with one hand while carefully lifting the panel up with the other hand. 3. Remove the panel from the foot. Step 2: Fix the mounting plate to the wall 1. Screw the mounting plate to the wall with the 4 supplied screws (A). 2. Slide back the loc...
Page 16 - Connecting the signals
Installation 16 Please make sure that the four shafts are securely placed in the notches of the mounting plate. 2. To secure the panel, slide forward the locks on both sides of the mounting plate. Lock the panel with one screw at both sides (D). Connecting the signals C D 1 2 3
Page 17 - To connect the power:; Starting up
Installation 17 To connect the video & sync signals: 1. Connect one end of the appropriate video cable to the corresponding video input of the monitor. • Analog video: Connect to input (3)• DVI: Connect to input (2) 2. Connect the other end of the video cable to the video output of your video so...
Page 18 - Note; Install the software
Installation 18 Note : The recommended resolution for best image quality is 1280x1024 at 60 Hz. The microcontroller in the display checks if the connected video signal has been adjusted before, and if these adjustments have been stored in the memory. There are 2 possibilities: a) The video signal ha...
Page 19 - Touch panel software:
Installation 19 Touch panel software: Please refer to the TouchKit installation & user manual on CD-ROM.
Page 20 - How to use the OSD; To change an OSD setting, proceed as follows:
On-screen display (OSD) 20 On-screen display (OSD) How to use the OSD The OSD is a window on your screen that allows you to view and change display settings. To change an OSD setting, proceed as follows: 1. Press the Menu key (3) on the front to display the OSD main menu. Note : It may be possible t...
Page 21 - Description of the menu items; Brightness / Contrast menu
On-screen display (OSD) 21 a) Press the < (left) key (1) or > (right) key (2) to change the value. b) Press the Menu key (3) to enter the new value and return to the menu. 5. The current settings are saved automatically when you return to the previous level or exit the OSD menu. 6. The Auto ke...
Page 22 - Image Control menu
On-screen display (OSD) 22 Image Control menu This menu is available only when an analog video signal is selected. Contrast To adjust the image brightness in relation to the background (the background is unchanged). This function controls the digital gain adjustment. Function Description Auto adjust...
Page 23 - Color Menu
On-screen display (OSD) 23 Color Menu Phase Manually adjusts the internal clock phase. When not adjusted correctly, vertical bands with alternate intensity appear in the image. Sharpness Manually adjusts the image sharpness (only for resolutions less than 1280 x 1024 pixels) Function Description 930...
Page 25 - Others Menu
On-screen display (OSD) 25 Others Menu Function Description Language Select the OSD language Input Select the desired video input. The analog video input has priority when both analog and DVI inputs are used. Timing Informa-tion Display timing information each time the timing changes. LANGUAGE > ...
Page 26 - Reset Menu
On-screen display (OSD) 26 Reset Menu Function Description Yes Select his function to reset all display parameters to the factory default settings No Select this function to exit from the Reset window without resetting the settings YES > NO > RESET
Page 27 - Maintenance; Panel
Maintenance 27 Maintenance Panel Take care not to damage or scratch the panel. Clean with a soft woolen or cotton towel. Use a watery solution or a mild commercial glass cleaning solution. Cabinet Do not use chemical cleaning products, benzene, toluene, xylene or other solvents. Clean with a soft cl...
Page 28 - Appendix A: Possible resolutions; Appendix A : Possible resolutions
Appendix A: Possible resolutions 28 Appendix A : Possible resolutions The following modes are preset as factory defaults. Resolution Pixel freq. (MHz) Hor. freq. (kHz) Vert.freq. (Hz) Standard Analog Digital 640 x 350 25.175 31.47 70 VGA V V 640 x 480 25.175 31.47 60 VGA/VESA V V 30.24 35.00 67 Mac ...
Page 29 - Appendix B: Technical specifications
Appendix B: Technical specifications 29 Appendix B: Technical specifications Picture panel 19-inch diagonal viewable screen TFT (thin film transistor) active matrix, color liquid crystal display, RGB interface Touch panel (MFCD 1219 TS only) Resistive technologyInterface: USB 1.1Input mode: stylus o...