Page 9 - ImagePRO; Quick Start Guide; Step 1: Connect Input Sources to ImagePRO; Step 5: Configure Input Sources
ImagePRO ™ Quick Start Guide Step 1: Connect Input Sources to ImagePRO ™ 1. Connect analog video source to the ImagePRO ™ using the three universal video inputs. 2. Connect any SDI video source to the SDI video input (ImagePRO-SDI ™ and ImagePRO-HD ™ only). 3. Connect DVI video source to the DVI vid...
Page 11 - Table of Contents
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor i Table of Contents IMAGEPRO ™ QUICK START GUIDE ____________________________________________________________________ I TABLE OF CONTENTS _________________________________________________________________________________ I CH...
Page 12 - IP
ii Image PRO – Multi Format Image Processor Manual # 26-0302000-00 / Revision E S AMPLE P HASE _________________________________________________________________________________________ 31 A CTIVE A REA __________________________________________________________________________________________ 31 C ON...
Page 13 - iii; IMAGEPRO; PRO’
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor iii CHAPTER FOUR_____________________________________________________________________________________ 61 SERIAL COMMAND SYNTAX _________________________________________________________________________ 63 S ERIAL P ARAMETERS ...
Page 15 - Introduction; What you will find in this chapter...; About ImagePRO; Features
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 1 1 CHAPTER ONE Introduction What you will find in this chapter… About ImagePRO TM Features Model IP-2003 ImagePRO – Multi Format Image Processor
Page 16 - Image
2 Image PRO – Multi Format Image Processor Manual # 26-0302000-00 / Revision E
Page 17 - Overview; Description
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 3 ImagePRO TM Overview Description The Folsom ImagePRO ™ is a powerful all-in-one signal processor that accepts a wide range of video input signals and processes them into a number of different output signal formats to meet ...
Page 18 - Additional ImagePRO-SDI
4 Image PRO – Multi Format Image Processor Manual # 26-0302000-00 / Revision E Additional ImagePRO-SDI ™ Features • One SD SDI input and output • Can be later upgraded to ImagePRO-HD • Motion adaptive de-interlacing for HDTV inputs • Low Video Delay • Logo image capture and recall feature • Dissolve...
Page 19 - INSTALLATION; Rear Panel Connectors
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 5 2 CHAPTER TWO INSTALLATION What you will find in this chapter… Rear Panel Connectors Rack-Mount Installation Video Input & Output Connections Remote Control Connections Power Cord/Line Voltage Selection Model...
Page 21 - Installation
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 7 Installation ImagePRO ™ Rear Panel Connectors UNIVERSAL INPUT 1 IN LOOP IN LOOP UNIVERSAL INPUT 2 H/C G/Y/COMPOSITE R/R-Y/C UNIVERSAL INPUT 3 B/B-Y V I N I N IN I N I N LOOP H/C UNIVERSAL INPUT 3 G/Y/COMPOSITE R/R-Y/C B/B-...
Page 25 - Video Input Connections; Universal Input Connectors
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 11 Video Input Connections Universal Input Connectors The video input section on the ImagePRO TM rear panel provides three universal inputs. Each input can accept RGB, YUV, S-Video (Y/C), or composite (NTSC, PAL or SECAM) vi...
Page 26 - Video Output Connections
12 Image PRO – Multi Format Image Processor Manual # 26-0302000-00 / Revision E Video Output Connections Four independently buffered outputs (one five wire BNC connection, one HD-15, one S-Video, and one Composite video BNC) are provided. Both 5-wire and HD-15 outputs provide the same Video in RGB o...
Page 27 - RGB/YPbPr Video Output; Composite Video Output
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 13 RGB/YPbPr Video Output Connect the output device to the set of BNC connectors marked R/R-Y, G/Y and B/B-Y on the output section of the ImagePRO ™ rear panel S-Video (Y/C) Video Output The Y/C video output connector is a 4...
Page 29 - RS-232 Remote Control Connections
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 15 RS-232 Remote Control Connections The Remote serial port can be connected to a PC or other Remote Controller to support remote control of the ImagePRO TM unit. Pinouts for the remote port are shown below. 1 2 3 4 5 6 7 8 ...
Page 30 - Power Cord/Line Voltage Selection; Tandem Plug
16 Image PRO – Multi Format Image Processor Manual # 26-0302000-00 / Revision E Connection to AC Power Power Cord/Line Voltage Selection ImagePRO TM is rated to operate with the following supplies: Input Power: 100-240 VAC, 47-63 Hz Power Consumption : 150 watts maximum The ImagePRO TM Wide Screen I...
Page 33 - CHAPTER THREE
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 19 3 CHAPTER THREE Operation What you will find in this chapter… Front Panel Controls Status Display Menu Control Setup Menus Input Setup Menu Output Setup Menu System Options Menu Test Pattern Menu Zoom Me...
Page 35 - Operation; Front Panel Controls
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 21 Operation ImagePRO ™ can be controlled by using the front panel menu controls or remotely via RS-232 or Ethernet interface. The front panel menu controls are described in detail in this section. Remote control commands ar...
Page 39 - Setting Ethernet
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 25 For ImagePRO-SDI and ImagePRO-HD units, when there is a logo image stored in non-volatile memory, the logo will be loaded into memory at this time. During this loading process, the following message will be displayed on t...
Page 40 - Status Display
26 ImagePRO – Multi Format Image Processor Manual # 26-0302000-00 / Revision E Status Display After power-up or anytime none of the four menu buttons are selected, the display will show a basic status. This screen gives information about the currently selected system inputs and outputs. The input se...
Page 42 - Menu Operation
28 ImagePRO – Multi Format Image Processor Manual # 26-0302000-00 / Revision E Menu Operation Setup This is the top-level menu accessed by pressing the SETUP button. Setup information can be stored in non-volatile memory within ImagePRO TM and will be automatically recalled each time the unit is tur...
Page 43 - will attempt to lock to the signal with the input video format; Type selection; YPbPr Colorspace selection
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 29 <in_format> Indicates the current input video format in the form, Hact x Vact @ Vr Hz (i.e 1024x768@75 Hz). If the currently selected input channel and source do not have a valid input signal, the <in_format> ...
Page 44 - Sampling; when making active
30 ImagePRO – Multi Format Image Processor Manual # 26-0302000-00 / Revision E The Color space value allows the user to select among the possible Component Video Standards for YPbPr. For all other video types the color space is RGB and cannot be selected or changed. The default selection for YPbPr i...
Page 45 - :1 Sampling Overview; :1 Sampling Operation
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 31 1:1 Sampling Overview In order to scale an image it must first be digitized. This is the process of changing the analog graphics signals (Red, Green, and Blue for example) into pixels stored in the ImagePRO TM image memor...
Page 46 - Contrast And Brightness; Aspect Ratio Submenu
32 ImagePRO – Multi Format Image Processor Manual # 26-0302000-00 / Revision E raster box is intentionally “broken” to allow the user to view the input video behind it and align the input video to the raster box precisely. Contrast And Brightness The adjustment range is 75.0% to 125.0%. 100% is the ...
Page 47 - Letterbox selection; Ratio
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 33 This menu allows the user to set the input signal aspect ratio. The menu is: The Mode value is selected among the following choices: 1:1, 3:2, 4:3, 5:4, 16:9, Custom The ImagePRO will select and display the input video as...
Page 48 - Video Processing Delay for ImagePRO
34 ImagePRO – Multi Format Image Processor Manual # 26-0302000-00 / Revision E De-interlacing In order to process an interlaced video source, the ImagePRO circuits must first de-interlace the image. De-interlacing is the process by which interlaced video (video where even lines are scanned during on...
Page 49 - Reset Config
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 35 NOTE: Configuration parameters entered in the input setup menu are saved in non-volatile memory for each input source by using the SAVE CONFIG menu item. If the SAVE CONFIG menu item is not selected, the information will ...
Page 50 - Recall Config
36 ImagePRO – Multi Format Image Processor Manual # 26-0302000-00 / Revision E Recall Config This menu allows the user to recall input configurations that were previously saved for the currently selected input format and type. Only configurations that match the current format and type will be displa...
Page 51 - NOTE: The Digital Cinema Projector resolutions at; Timing Adjust Submenu; OUTPUT
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 37 Output Setup Submenu This menu is used to configure the outputs of the ImagePRO. The Output Setup Menu is illustrated below. This menu can be accessed from the SETUP MENU. NOTE: Configuration parameters entered in this me...
Page 52 - H Position
38 ImagePRO – Multi Format Image Processor Manual # 26-0302000-00 / Revision E For the Horizontal entries, the unit of measure is pixels. H Total indicates the total pixel count per line. H Position sets the offset of start of active area from H sync. H Active sets the size of the active area. H Syn...
Page 53 - Sync Settings Submenu
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 39 Sync Settings Submenu This menu allows the user to specify the sync types for the current output. The submenu is illustrated below: The Sync Out menu item selects among the five possible output sync types: CSync, +H+V, +H...
Page 54 - Flicker Reduce
40 ImagePRO – Multi Format Image Processor Manual # 26-0302000-00 / Revision E Flicker Reduce The Flicker Reduce value is n/a when the output format is non-interlaced. For interlaced formats, the range is Off (no flicker reduction) or +1 (minimum flicker reduction) through +20 (maximum flicker reduc...
Page 55 - H Phase
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 41 With ImagePRO-SDI or ImagePRO-HD units, when Genlock type HV is selected, and the ImagePRO output is interlaced, the message “FOR SDI OUT” is displayed as shown below: H Phase The H Phase setting allows the output H timin...
Page 56 - will automatically
42 ImagePRO – Multi Format Image Processor Manual # 26-0302000-00 / Revision E When Input Auto Acquire is On, the system will always perform a full sync acquisition on the input signal anytime the input channel is selected, the input type is changed, or the input signal changes sync rates. When Auto...
Page 57 - Save As Submenu; H Total
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 43 Formats Submenu This menu is used to define and save a new video format, or to edit and save a previously-defined format. These saved formats are stored in a user library, which is searched during the auto-acquisition pro...
Page 59 - Delete Submenu
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 45 If the user picks a name that's already in use in the user library, a confirmation menu is displayed when the user invokes the Save command: Pressing the SEL key will cause the existing library format to be overwritten wi...
Page 60 - V Rate
46 ImagePRO – Multi Format Image Processor Manual # 26-0302000-00 / Revision E If the format selected for deletion is currently an Input format used by any of the input channels or is the Input format that is saved in an input configuration, the following screen will be displayed: H,V Parameters The...
Page 61 - Views Submenu; Recall
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 47 Views Submenu The Views menu allows management of up to 16 stored “Views”. A View is a combination of zoom and pan settings. For example, the user may define a view that maps the entire input image to the upper left quart...
Page 62 - Delete
48 ImagePRO – Multi Format Image Processor Manual # 26-0302000-00 / Revision E The view to delete is selected from the list of available views. Deleting a view simply resets its pan and zoom settings to their default values. A confirmation screen will appear when SEL is pressed. DELETE VIEW > Vie...
Page 63 - Effects Submenu
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 49 Effects Submenu The effects menu selects the transition effect when switching between input channels. The user may select form the following selections: - Transition with Image Cut; The currently selected channel will be ...
Page 64 - Tech Support Submenu
50 ImagePRO – Multi Format Image Processor Manual # 26-0302000-00 / Revision E Tech Support Submenu The version displayed is the installed operating firmware version number. TECH SUPPORT Version <fw_ver> Phone 866-FRI-SUPT
Page 65 - System Submenu
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 51 System Submenu This menu allows the user to adjust the VFD Brightness and remote control setting for RS-232 or Ethernet Interfaces as illustrated below. NOTE: Configuration parameters entered in the system menu are saved ...
Page 66 - Ethernet Submenu
52 ImagePRO – Multi Format Image Processor Manual # 26-0302000-00 / Revision E The handshake value is selected from the following values: Off or On (CTS/RTS). The reset command restores the RS232 settings to defaults: 38400, N81, Handshake On. After connecting the PC COM port to the ImagePRO RS-232 ...
Page 68 - it will interfere with the programming operation causing; Program EDID
54 ImagePRO – Multi Format Image Processor Manual # 26-0302000-00 / Revision E EDID DVI Input Format submenu This menu allows the user to update the ImagePRO-HD ™ ’s EDID’s preferred resolution. NOTE: This menu is for advanced users only. Do not reprogram the EDID unless it is necessary. This menu i...
Page 70 - Save System State
56 ImagePRO – Multi Format Image Processor Manual # 26-0302000-00 / Revision E Save System State This command explicitly saves all settings in the system state submenu so they may be restored at power up. This command will also save the currently selected input channel as the default input selection...
Page 72 - Zoom Menu
58 ImagePRO – Multi Format Image Processor Manual # 26-0302000-00 / Revision E Zoom Menu This menu is invoked by pressing the ZOOM button. The default zoom amount is 100%. By selecting Amount and pressing SEL the user may increase zoom above 100% (zoom into the input Video) or decrease zoom below 10...
Page 75 - CHAPTER FOUR; Remote Commands; Serial Command Syntax; Command List/Description
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 61 4 CHAPTER FOUR Remote Commands What you will find in this chapter… Serial Command Syntax Remote Commands ImagePRO TM Command List/Description Model IP-2003 ImagePRO – Multi Format Image Processor
Page 77 - Serial Parameters; must
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 63 Serial Command Syntax Serial Parameters The following are the default parameter settings for serial communication. Baud Rate is 38.4K. Parity is NONE. Stop Bit is 1. Data Bit is 8. For RS-232 signal connections, refer to ...
Page 82 - Resolution Remote Commands; RESH
68 ImagePRO – Multi Format Image Processor Manual # 26-0302000-00 / Revision E ImagePRO TM Command List/Description Resolution Remote Commands Command: RESH Description: Query the available resolution list for the ImagePRO. Parameters: None Returns: All available resolutions in the format: n : HxV @...
Page 83 - Input Remote Commands
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 69 Input Remote Commands Command: ACQ mode Description: Turns Auto acquisition mode off/on. Parameters: mode [0 | 1] Off | On Query: ACQ? Returns Auto acquisition mode in the format = mode Example: ACQ 0 (Turns auto acquisit...
Page 91 - Output Remote Commands
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 77 Output Remote Commands Command: GLMODE src type Description: Sets Genlock Source and Genlock Type Parameters: src [0-4], Freerun | Input Video | H+V Sync | C Sync | Black Burst type [1-3], V Lock | HV Lock | HVScLock(Full...
Page 93 - OHATV nnnn; OHSYNC nnnn; OHTOTAL nnnn
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 79 Command: OHATV nnnn Description: Set Output Horizontal Active. The minimum and maximum limit is dependent on the output resolution. Parameters: nnnn - Output Horizontal Active: nnnn[ (Actual Output H Active * 2/10, with a...
Page 96 - OVPOS nnnn; OVSYNC nnnn; OVTOTAL nnnn
82 ImagePRO – Multi Format Image Processor Manual # 26-0302000-00 / Revision E of 150) - +(Actual Output V Active *6/5, with absolute maximum value of Output V Total – Output V Sync)] Query: OVATV? Returns the Output Vertical Active value in the format = nnnn Example: OVATV 768 (Set Output Vertical ...
Page 97 - Edit Custom Format Remote Commands; EFLIST
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 83 Edit Custom Format Remote Commands Command: EFLIST Description: Lists the names of all saved custom formats. Parameters: None Returns: List the names of saved custom formats, one name per line. Example: EFLIST (Lists all ...
Page 100 - EFDEL filename
86 ImagePRO – Multi Format Image Processor Manual # 26-0302000-00 / Revision E EFDEL filename Description: Deletes saved custom format. This filename is translated to all upper case characters Parameters: filename – name of custom format to be deleted (translated to upper case). Example: EFDEL FORMA...
Page 101 - System and Ethernet Remote Commands
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 87 System and Ethernet Remote Commands Command: DMSG mode Description: Sets Debug message display mode. Parameters: mode - DMSG mode [0-1] Off | On Query: DMSG? Returns the Debug message display mode in the format = mode Exa...
Page 103 - Logo Remote Commands; LOGOD
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 89 Logo Remote Commands Command: LOGOD Description: Delete Logo image from non-volatile memory. Selecting Black/Logo channel will now display black. Logo feature only available on ImagePRO-SDI and ImagePRO-HD. Parameters: No...
Page 104 - Effects Remote Commands; TRN type in
90 ImagePRO – Multi Format Image Processor Manual # 26-0302000-00 / Revision E Effects Remote Commands Command: TRN type in Description: Selects transition type when switching between inputs. Transition delay is only applicable if the transition type selected is Fade to black / Fade to logo. Fade to...
Page 105 - nn –
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 91 Pan / Zoom / View Remote Commands Command: PANH nnn.n Description: Set Output Horizontal Pan. Parameters: nnn.n - Horizontal Pan (-100.0% - +100.0%) Query: PANH? Returns the Output Horizontal Pan value in the format = nnn...
Page 109 - CHAPTER FIVE; Software; Software Upgrade Instructions
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 95 5 CHAPTER FIVE Software Upgrade Instructions What you will find in this chapter… Software Upgrade Instructions Model IP-2003 ImagePRO – Multi Format Image Processor
Page 113 - Barco; Warranty
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 99 6 CHAPTER SIX Barco Folsom Information What you will find in this chapter… Warranty RMA Information Technical Support/General Contact Information Model IP-2003 ImagePRO – Multi Format Image Processor
Page 115 - Barco Folsom Information; Barco Folsom Warranty; Sales Contact Information; Technical Support Information; General Company Information; Barco Folsom Europe
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 101 Barco Folsom Information Barco Folsom Warranty All video products are designed and tested to the highest quality standards and are backed by a full 3-year parts and labor warranty. Warranties are effective upon delivery ...
Page 117 - Technical Specifications
Manual # 26-0302000-00 / Revision E ImagePRO – Multi Format Image Processor 103 A APPENDIX Technical Specifications Model IP-2003 ImagePRO – Multi Format Image Processor
Page 120 - User Control
106 ImagePRO – Multi Format Image Processor Manual # 26-0302000-00 / Revision E User Control Local: User-friendly front panel interface Ethernet connection (with TCP/IP) or RS-232 serial port for real-time control Physical Height: 1.5"; Width: 17" (43.2 cm) or 19" (48.3 cm) with rack-mou...
