Barco r5976832/07 - Manual

1. Safety 1.3 Important warnings Important warnings: Risk of electric shock: Do not open. To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Refer servicingto qualified service personnel. RISK OF ELECTRICAL SHOCK DO NOT OPEN CAUTION CAUTION : TO RE...

1. Safety 1.4 Important warnings concerning flight cases Important warnings concerning stacking/transporting OLite rental flight cases • Stack maximum two (2) OLite rental flight cases high. Never higher. • Surface on which flight case is standing must be level to ensure that the total load is evenl...

2. Installation requirements 2. INSTALLATION REQUIREMENTS About this chapter This chapter enumerates the mechanical requirements for the OLite display, the electrical requirements to power up the OLite displayand the system requirements to run the control software efficient. Overview • Mechanical re...

2. Installation requirements 2.1 Mechanical requirements for the OLite rental display Weight Do not underestimate the weight of a complete OLite rental display. Be sure that the floor or truss installation on which the OLiterental display has to be installed is capable of handling five (5) times the...

2. Installation requirements 2.2 Electrical requirements for the OLite rental display Power requirements One OLite tile requires 200-240 VAC, 50-60 Hz, 4.22 amps at 230 VAC. Note that one OLite tile correspond with a display surfaceof 0.6 m². Each OLite tile has a control box with a power loop throu...

2. Installation requirements 2.3 System requirements for the Control software Before you begin Is assumed you are familiar with the Windows operating system at your site. The CD-ROM in your package contains a Windows-based installation program. You can install the software from the CD-ROM. System re...

3. System overview 3. SYSTEM OVERVIEW Overview • Introduction R5976832 OLITE RENTAL DISPLAY 29/05/2007 13

3. System overview 3.1 Introduction The fundamental elements of an OLite rental display system are: • OLite modules. • OLite rental structure. • OLite rental foot, foot beams and stacker or OLite rental truss beams • Rental power box. • Digitizer. • Control software. Block diagram OLite display syst...

4. Components of an OLite rental tile 4. COMPONENTS OF AN OLITE RENTAL TILE General introduction The OLite rental tile has a rugged frame where OLite modules fit into to form one display tile. These modules are connected via acable string with the OLite control box mounted inside the OLite rental fr...

4. Components of an OLite rental tile 4.1 OLite rental frame Introduction OLite rental frame The OLite rental frame is made out of aluminium profiles and stainless steel to reduce weight without losing strength. This strongframe allows you to build OLite LED-walls up to 12 frames high stacked or 15 ...

4. Components of an OLite rental tile 4.2 OLite module Introduction OLite module The front of an OLite module consists of a matrix of full color SMD LED’s enclosed by a shader and sheltered in an IP65 housing. Therear of the OLite module is equipped with two positioning pins and two snap-in latches ...

4. Components of an OLite rental tile Parts location of an OLite 510 module A D I J C E C E F B C D E G H Image 4-6OLite 510 module ( R9853020 ). A Shader. B Full color LED. C Module positioning pin.D External fan cover.E Snap-in latch. F Hole for thread rolling screw M3. G Red status LED.H Green st...

4. Components of an OLite rental tile 4.3 OLite control box Introduction OLite control box The OLite control box contains a power supply unit, a distribution interface and a controller/re-sync unit. All together assembled inan IP65 housing. The control box is attached to a mounting plate which makes...

5. OLite rental peripherals and accessories 5. OLITE RENTAL PERIPHERALS AND ACCESSORIES Overview • OLite rental flight case • OLite rental base stand setup accessories • OLite rental truss setup accessories • Power boxes • Digitizer • Fiberlink system • Control software R5976832 OLITE RENTAL DISPLAY...

5. OLite rental peripherals and accessories 5.1 OLite rental flight case Introduction of the OLite rental flight case The OLite rental flight case holds up to 4 tiles and is specially designed to enable fast build up directly from flight case to display.The tiles inside the flight case are separated...

5. OLite rental peripherals and accessories 5.2 OLite rental base stand setup accessories Base stand setup accessories To setup an OLite rental display in a base stand configuration, additional mounting accessories are required as there are the footbeams, the OLite rental foot and the OLite rental s...

5. OLite rental peripherals and accessories 5.3 OLite rental truss setup accessories Truss setup accessories OLite truss beams are required to set up an OLite rental display in a hanging configuration. Barco offers two sizes of OLite trussbeams, namely the “OLite single truss beam” and the “OLite du...

5. OLite rental peripherals and accessories 5.4 Power boxes General To ensure safe and reliable operation of the OLite , a suitable system for AC power distribution must be used. Though 3 rd. party solutions may be used, several sizes and types of power distributions are available from Barco. For sm...

5. OLite rental peripherals and accessories 5.5 Digitizer General The digitizer processes (image processing, conversion and conditioning) all source signals for digital distribution to every tile. Thedigitizer can be accessed directly or via the control software (e.g. Director toolset). This softwar...

5. OLite rental peripherals and accessories 5.6 Fiberlink system General If the distance between the digitizer and the LED-wall exceeds 5 meters, a fiber optic connection must be used to ensure signalintegrity and system reliability. Barco offers two complete system solutions including transmitter, ...

5. OLite rental peripherals and accessories 5.7 Control software General The control software is designed as a graphic user interface (GUI) and can be used to control and configure the digitizer as well asthe Barco LED wall via a PC (e.g. Director toolset). Minimum required software version: 1.06 Im...

6. Set up process of an OLite rental display 6. SET UP PROCESS OF AN OLITE RENTAL DISPLAY About this chapter This chapter describes roughly the installation process of the OLite rental display for a base stand (floor mount) or truss (hanging)configuration. Several process stages refer to one or more...

6. Set up process of an OLite rental display 6.1 Set up of a floor mount OLite rental display Set up process 1. Installation of the foot beams and OLite rental feet. See detailed procedure "Install the OLite rental feet", page 41. 2. Installation of the adjustable feet. Note that this is opt...

6. Set up process of an OLite rental display 6.2 Set up of a hanging OLite rental display Set up process 1. Build up the truss installation. Warning: Make sure that the truss installation, on which you want to hang the OLite rental display, complies with the localregulations regarding such installat...

7. Basic set up procedures 7. BASIC SET UP PROCEDURES About this chapter This chapter contains all installation procedures necessary to set up an OLite rental display. These procedures describe, with de-tailed step by step actions and illustrations, how to install an OLite rental display in a floor ...

7. Basic set up procedures 7.1 Remove OLite rental tiles out of the flight case Necessary tools • OLite single truss beam. • Hoisting equipment. How to remove the OLite rental tiles out of the flight case ? 1. Open the four lock handles of the flight case. 2. Remove the flight case cover by lifting ...

7. Basic set up procedures 7.2 Place OLite rental tiles into the flight case Necessary tools • OLite single truss beam. • Hoisting equipment. How to place OLite rental tiles into the flight case ? 1. Place an empty open flight case trolley on a level surface to ensure the load will be evenly spread ...

7. Basic set up procedures 7.3 Install the OLite rental feet Necessary tools • 19 mm wrench. • Spirit level. Necessary parts • OLite rental feet. • 2 foot beams per rental foot. • Four M12 bolts per rental foot. • Shim plates. How to install the OLite rental feet ? 1. Place two foot beams parallel p...

7. Basic set up procedures 7.4 Install an adjustable foot Necessary tools • Allen key size 4 mm • Hexagon socket size 10 mm How to install an adjustable foot ? 1. Ensure there are no obstacles to obstruct the smooth placement of the adjustable foot. 2. Slide an adjustable foot into the cross beam. B...

7. Basic set up procedures 7.5 Attach an OLite truss beam upon an OLite rental tile The following procedure is written and illustrated for a single OLite truss beam. The same procedure can beapplied for a dual OLite truss beam. Four lock handles instead of two have to be manipulated. How to attach a...

7. Basic set up procedures 7.6 Attach an OLite rental tile upon an OLite rental foot How to attach an OLite rental tile upon an OLite rental foot ? 1. Ensure that the OLite rental foot is installed well to support the OLite rental tiles. 2. Ensure that both locking mechanisms at the bottom of the OL...

7. Basic set up procedures 7.7 Attach OLite rental tiles on top of each other How to attach OLite rental tiles on top of each other ? 1. Ensure that both locking mechanisms at the bottom of the OLite rental tile are unlocked. So, handles in vertical position and pulled out. 1 2 Image 7-13Place the t...

7. Basic set up procedures 7.8 Attach OLite rental tiles next to each other How to attach OLite rental tiles next to each other ? 1. Place the side latch hook of the adjoining edge in open position by turning the small handle as far as possible clockwise. Image 7-15Turn the small handle clockwise as...

7. Basic set up procedures 7.9 Install an OLite stacker system OLite stacker An OLite stacker is installed opposite every adjoining edge of two OLite rental columns and is required for OLite displays higher thantwo OLite tiles. Necessary tools 19 mm wrench. Necessary parts Eight M12 bolts per stacke...

7. Basic set up procedures 7.10 Build up a floor mounted OLite rental display Floor mounted OLite display A floor mounted OLite rental display is built upon OLite rental feet. The OLite tiles are placed successively from left to right (or rightto left) and row by row. W ARNING : The foot beams on wh...

7. Basic set up procedures 7.11 Build up a hanging OLite rental display with truss beams Hanging OLite rental display A hanging OLite rental display is built up row by row. Each row is built by placing the OLite rental flight cases next to each other andfastening the OLite tiles side by side. The co...

7. Basic set up procedures 7.12 Secure a hanging OLite rental display Necessary parts Safety steel cables or chains. How to secure a hanging OLite rental display ? 1. Lift up the OLite display to the desired height. 2. Place a safety steel cable or chain around the truss installation above the OLite...

8. Cabling of an OLite rental display 8. CABLING OF AN OLITE RENTAL DISPLAY Outdoor plugs and sockets for OLite rental tiles Barco uses custom designed outdoor sockets for power and data connections from tile to tile and to other peripherals. These ruggedsockets are watertight (IP65) when used with ...

8. Cabling of an OLite rental display 8.1 Power cabling of an OLite rental display Power boxes Barco provides several types of power boxes. Depending on the size of the OLite rental display you can choose to use the monophase power box, custom made power box or rental power box. The type of power bo...

8. Cabling of an OLite rental display 8.2 Data cabling of an OLite rental display Necessary parts • Data linking cables. • One dummy data plug. How to realize the data cabling of an OLite rental display ? 1. Connect the data cable coming from the digitizer with the data input socket of the first til...

8. Cabling of an OLite rental display 8.3 Module interconnection of an OLite 510 rental frame Interconnection diagram The OLite 510 rental frame contains eight columns of eight OLite 510 modules. These columns are grouped per two and orderedfrom right to left, seen from the rear of the tile. A cable...

8. Cabling of an OLite rental display 8.4 Module interconnection of an OLite 612 rental frame Interconnection diagram The OLite 612 rental frame contains eight columns of six OLite 612 modules. These columns are grouped per two and ordered fromright to left, seen from the rear of the tile. A cable s...

9. OLite creativity pack 9. OLITE CREATIVITY PACK Introduction The OLite modules, used in the OLite rental tile, can be used in a different arrangement than the standard set up of 64 OLite 510or 48 OLite 612 modules per tile. You can place the OLite modules in a creative way to integrate the modules...

9. OLite creativity pack 9.2 OLite support grid Design guidelines It’s obvious that the design of the support grid for the OLite modules must comply with several requirements regarding dimensions,strength, accessibility, etc. The housing of the OLite modules is provided with snap-fits for fast and e...

9. OLite creativity pack 9.3 Possibilities Control box possibilities • All six (6) output ports of the control box are activated. • Up to 16 OLite 510 modules per output port. • Up to 64 OLite 510 modules per control box (due to power limitations). • Up to 12 OLite 612 modules per output port. • Up ...

9. OLite creativity pack Extension cables possibilities • Extension cables can be combined to make up intermediate lengths. However, always use a minimum of extension cables tobridge the distance between output port and module or between two modules. So, use a 5 meter extension cable instead of 5tim...

9. OLite creativity pack 9.4 OLite creativity example Cabling example The illustration below shows an interconnection diagram of the OLite 510 modules and the output ports of the control box. Thesix output ports of the control box are used and all extension cables in the cabling have a length of 1 m...

10. Maintenance 10.1 Cleaning OLite tiles Why cleaning OLite tiles ? Due to outdoor use the OLite tiles are exposed to all kinds of weather conditions. Sand, dust, smog and other dirt adhere on the OLitetiles and because of that the performance of the OLite tiles can be reduced. That’s why cleaning ...

11. OLite options 11.1 Optional OLite back cover Overview • Back cover for OLite rental tiles • Back cover installation procedure 80 R5976832 OLITE RENTAL DISPLAY 29/05/2007

11. OLite options 11.1.1 Back cover for OLite rental tiles Introduction Some LED-wall applications require an aesthetic look for the rear of the LED-wall. Therefore, Barco offers an optional back coversystem as a kit to close the rear of the OLite rental tile. The back cover system is attached to th...

12. Servicing 12.1 Safety instructions Personal protection W ARNING : Ensure you understand and follow all the safety guidelines, safety instructions, warnings and cautions mentioned in this manual. W ARNING : Be aware of suspended loads. W ARNING : Wear a hard hat to reduce the risk of personal inj...

12. Servicing 12.2 OLite module diagnostic Status LED’s OLite module The OLite module is provided with two status LED’s. One green and one red LED. The two status LED’s are located just below theexternal fan. The red LED indicates the status of the software and the microprocessor. The green LED indi...

12. Servicing 12.3 Replace the OLite control box How to replace the OLite control box ? 1. Read and heed the servicing safety instructions. 2. Disconnect the power and data linking cables from the OLite control box. Caution: Always disconnect the power cord from the OLite control box before connecti...

12. Servicing 12.4 Replacement of an OLite module on-site This procedure is illustrated with OLite 510 modules. Nevertheless, the same procedure is valid for OLite 612modules as well. W ARNING : Always use this procedure on OLite modules which are mounted in the display. The use of a module safety c...

A. Dimensions A.1 Dimensions of an OLite rental tile Dimensions OLite frame 896 mm 672 mm 703 mm 276 mm 396 mm 246 mm 294 mm Image A-1 Dimensions OLite frame with OLite 510 modules 896 mm 672 mm 703 mm 262,42 mm 310,42 mm Image A-2 94 R5976832 OLITE RENTAL DISPLAY 29/05/2007

A. Dimensions Dimensions OLite frame with OLite 612 modules 896 mm 672 mm 703 mm 264,2 mm 312,2 mm Image A-3 R5976832 OLITE RENTAL DISPLAY 29/05/2007 95

A. Dimensions A.2 Dimensions of an OLite module Dimensions of an OLite 510 module 16,42 41,8 83,6 41,8 5,8 52,5 100 111,6 Image A-4Dimensions given in millimeters. Dimensions of an OLite 612 module 18,23 55,8 111,6 55,8 5,8 54,33 100 111,6 Image A-5Dimensions given in millimeters. 96 R5976832 OLITE ...

A. Dimensions A.3 Dimensions of an OLite control box Dimensions 1 0 7 1 4 5 2 9 0 3 6 4 3 7 3 7 7 296,5 324 285 132,6 Image A-6Dimensions given in millimeters. R5976832 OLITE RENTAL DISPLAY 29/05/2007 97

A. Dimensions A.4 Dimensions of an OLite flight case Dimensions 1440 mm 1384 mm 960 mm 9 7 9 ,5 m m 880 mm Image A-7 98 R5976832 OLITE RENTAL DISPLAY 29/05/2007

A. Dimensions A.5 Dimensions of an OLite truss beam Dimensions single truss beam 891 150 1 0 9 1 4 0 2 6 0 3 0 8 1 3 Image A-8Dimensions given in millimeters. Dimensions dual truss beam 1787 220 1 0 9 1 4 0 2 6 0 3 0 8 Image A-9Dimensions given in millimeters. R5976832 OLITE RENTAL DISPLAY 29/05/200...

A. Dimensions A.6 Dimensions of an OLite foot Dimensions 1 2 0 1 8 0 1 1 9, 1 5 1 5 0, 1 5 2 4 9, 5 892 704 8 40 Image A-10Dimensions given in millimeters. 100 R5976832 OLITE RENTAL DISPLAY 29/05/2007

A. Dimensions A.7 Dimensions of an OLite stacker system Dimensions stacker foot 690 mm 119,15 mm 2 6 2 m m Image A-11 Dimensions stacker profile 1394 mm 200 mm 110,6 mm Image A-12 Dimensions stacker bridge 602 mm 117,6 mm 2 0 0 m m Image A-13 R5976832 OLITE RENTAL DISPLAY 29/05/2007 101

A. Dimensions A.8 Dimensions of the foot beams Dimensions foot beams 1200 / 2400 / 4000 70 16 0 Image A-14Dimensions given in millimeters. 102 R5976832 OLITE RENTAL DISPLAY 29/05/2007

B. Specifications B.1 Specifications of the OLite 510 rental tile Specifications Lifetime 50.000 hours Pixel pitch 10 mm Calibrated Brightness 5000 NIT LED configuration 3-in-1 SMD Pixel density 5.632 LEDs per tile (88 x 64 px) Hor. viewing angle > 145° Vert. viewing angle > 95° Contrast 810 P...

B. Specifications B.2 Specifications of the OLite 612 rental tile Specifications Pixel pitch 12 mm Calibrated Brightness 6,000 Nit LED configuration 3-in-1 SMD Pixel density 3,888 LEDs per tile (72x54) Hor. viewing angle > 145° Vert. viewing angle > 80° Lifetime 50,000 hours Power consumption ...

B. Specifications B.3 Weight of individual parts of an OLite rental display Weight of individual parts OLite control box 8 kg OLite 510 module 360 gram Total weight 4 OLite 510 cable strings 3 kg OLite 612 module 480 gram Total weight 4 OLite 612 cable strings 3 kg OLite rental frame (without contro...

B. Specifications B.4 Ballast values for a base stand OLite display All calculations are based upon a wind load of 0,8 kN/m² (±129 km/h) which comply with the TUV regulations.For more information consult the “Ballast calculator” tool, available on Barco’s web site. The ballast values are given per O...

B. Specifications Position OLite display upon foot beams for minimum ballast Lw Lb Ballast 1 2 3 ... n 0,3 m Image B-2 Single OLite rental foot Height Tiles Used foot beam (Lb) Beam length in front of display (Lw) Minimum ballast (kg) 1 2,4 meter > 0,93 meter (maximum 1,2 meter) 0 2 2,4 meter >...

B. Specifications B.5 Ground pressure of a base stand OLite display All calculations are based upon a wind load of 0,8 kN/m² (±129 km/h) which comply with the TUV regulations.For more information consult the “Ballast calculator” tool, available on Barco’s web site. The ballast values are given per O...

C. Order info C.1 Spare part order info Order info: Order info Description R9010330 Complete OLite 510 rental tile (controller and modules included) R9853010 OLite 510 rental frame (empty) R9853020 OLite 510 module R98530205 OLite 510 module (5 pieces) R98530220 OLite 510 module (20 pieces) R9853090...

Index INDEX A Accessories 23, 26–27Adjustable foot 43Available packages 68 Creativity pack 68 B Ballast values 107Base stand 26 Accessories 26 Basic set up procedures 37Build up 50, 53 Floor mount 50Hanging display 53 C Cabling 59Cleaning 78Components 15Control box 97 Dimensions 97 Creativity pack 6...