Page 5 - Table of contents; TABLE OF CONTENTS
Table of contents TABLE OF CONTENTS 1. Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1Important Safety Instructions . . . . . . . . . . . ....
Page 7 - Important Safety Instructions
1. Safety 1. SAFETY 1.1 Important Safety Instructions Instructions: • Read these instructions. • Keep these instructions. • Heed all warnings. • Follow all instructions. • Do NOT submerge fully or partly in water or other liquids. • Clean only with materials or chemicals that are inert, nonabrasive,...
Page 8 - Important Warnings
1. Safety 1.2 Important Warnings Important Warnings: • Risk of electric shock: Image 1-1Risk of electrical shock Risk of electric shock. Do not open. To reduce the risk of electric shock, do not remove cover (orback). No user-serviceable parts inside. Refer servicing to qualified service personnel.T...
Page 11 - General functionality; Overview; Order info D320PL Digitizer; Technical summary; Summary
2. Introduction 2. INTRODUCTION 2.1 General functionality Overview The D320PL is a video processing device, designed to drive as well Barco LED walls as large screenprojectors, monitors, plasma screens, ... etc. The D320PL is capable of handling all standard outputformats like SVGA, XGA, SXGA and UX...
Page 13 - Dimensions of the D320PL Digitizer; Dimensions
2. Introduction 2.4 Dimensions of the D320PL Digitizer Dimensions Image 2-2 R5976470 D320PL DIGITIZER 13122002 9
Page 15 - Physical Installation of the D320PL Digitizer; PHYSICAL INSTALLATION OF THE; Installation requirements; Requirements
3. Physical Installation of the D320PL Digitizer 3. PHYSICAL INSTALLATION OF THE D320PL DIGITIZER 3.1 Installation requirements Requirements • The D320PL Digitizer should not be placed in a built-in installation or enclosure unless proper venti-lation is provided. • When using the unit in a multi-un...
Page 16 - Connections; Rear panel inputs/outputs
3. Physical Installation of the D320PL Digitizer 3.2 Connections Rear panel inputs/outputs Image 3-2 A LED-WALL / PROJECTOR OUTPUTB Power SwitchC Power inputD LOOP INE LOOP OUTF Retractable dust filterG COM1 : RS232 inputH COM2 : RS232 chaining outputI COM3 : RS232 stacking output J TCP-IP : Etherne...
Page 17 - Removing and inserting a D320PL Digitizer input module; How to remove an input module from the D320PL Digitizer
3. Physical Installation of the D320PL Digitizer • A : LED-WALL / PROJECTOR OUTPUT (DVI output connector with 3 functions) - LED wall out (Barco proprietary protocol). - RGB HV out (analog). - DVI digital out. (DVI compliant, eg: monitor, projector, plasma, ... ) • B : Power switch - The power ON/OF...
Page 18 - How to insert an input module into the D320PL Digitizer
3. Physical Installation of the D320PL Digitizer Image 3-3 How to insert an input module into the D320PL Digitizer 1. Gently slide in the input module into a free input slot with the grip handle at the top. 2. Locking in the module by pushing the input module completely into the D320PL Digitizer unt...
Page 19 - DVI input module
4. Input modules 4. INPUT MODULES Overview • DVI input module • SDI input module • HDSDI input module • CVBS / S-VID input module • YUV / RG(s)B input module • RGB analog input module • Dummy input module 4.1 DVI input module Technical info: • Computer generated graphical source. • DVI data in. • 16...
Page 20 - SDI input module; HDSDI input module
4. Input modules 4.2 SDI input module Technical info: • SDI data in. • SDI loop through. • 270Mbit/s transmission (SMPTE 259M-C). • 525/625 interlaced. • Coax (75 Ohm). • Amber LED (upper LED on the front side) will be lit indicating recognition of film, either continuous orintermittent film detecti...
Page 23 - RGB analog input module
4. Input modules Image 4-9 Image 4-10 Order info: Article No. Description R9850940 D320PL Digitizer YUV / RG(s)B input module 4.6 RGB analog input module Technical info: • Sub D15 connector for input and loop through. • R, G, B, Hsync, Vsync : 0 to 1 Vpp ±3dB 75 Ohm termination. • Black level : 300m...
Page 24 - Dummy input module; Technical info
4. Input modules 4.7 Dummy input module Technical info • Dimensions : 103 x 181 x 41(W x D x H) Image 4-13 Image 4-14 Order info: Article No. Description R9850930 D320PL Digitizer dummy input module 20 R5976470 D320PL DIGITIZER 13122002
Page 25 - Cables and accessories for the D320PL Digitizer; CABLES AND ACCESSORIES FOR THE; Cables and accessories; List with available cables and accessories
5. Cables and accessories for the D320PL Digitizer 5. CABLES AND ACCESSORIES FOR THE D320PL DIGITIZER 5.1 Cables and accessories List with available cables and accessories Article No. Description Image R326103 Power cable with CEE7 plug. image 5-1 R3261115 Power cable with NEMA 5–15 plug. image 5-2 ...
Page 27 - Configuration schemes; CONFIGURATION SCHEMES; Stand alone configuration; Chaining configuration; Scheme
6. Configuration schemes 6. CONFIGURATION SCHEMES 6.1 Stand alone configuration Scheme Image 6-1 One D320PL Digitizer is sufficient to drive one Barco LED wall with four different sources. How to set up a D320PL stand alone configuration 1. Connect the RS232 communication port of the local control P...
Page 28 - How to set up a D320PL chaining configuration; Stacking configuration
6. Configuration schemes The D320PL Digitizer can be chained in order to generate more windows on the output display (four win-dows per D320PL Digitizer). How to set up a D320PL chaining configuration 1. Connect the RS232 communication port of the local control PC with the COM1 RS232 input port of t...
Page 29 - How to set up a D320PL stacking configuration; Combined chained and stacked configuration
6. Configuration schemes How to set up a D320PL stacking configuration 1. Connect the RS232 communication port of the local control PC with the COM1 RS232 input port of the first D320PL Digitizer. This Digitizer will act as the master, all following Digitizers are slaves. 2. Connect the LOOP OUT wit...
Page 30 - How to set up a mixed configuration
6. Configuration schemes How to set up a mixed configuration 1. Connect the RS232 communication port of the local control PC with the COM1 RS232 input port of the first D320PL Digitizer. This Digitizer will act as the master, all following Digitizers are slaves. 2. Connect the LOOP OUT of each previ...
Page 31 - XLite Toolset; General introduction
7. Control Software 7. CONTROL SOFTWARE 7.1 XLite Toolset General introduction The XLite Toolset (R9850042) is used to configure and control the D320PL Digitizer from basic set-up toadvanced features such as chroma keying, alpha blending or window positioning. Refer to the manual(R5976380) for more ...
Page 33 - Maintenance of the D320PL Digitizer; MAINTENANCE OF THE D320PL; Cleaning the dust filter; How to clean the dust filter; Cleaning the cabinet; How to clean the cabinet
8. Maintenance of the D320PL Digitizer 8. MAINTENANCE OF THE D320PL DIGITIZER 8.1 Cleaning the dust filter The fan intake grill of the D320PL Digitizer has a retractable dust filter which mustbe checked for good functionality on regular basis. Never allow this filter to becomeblocked up. How to clea...
Page 37 - Index; INDEX
Index INDEX A Accessories 21 C Cables 21Cleaning 29 Air dust filter 29Cabinet 29 Configuration scheme 23–25 Chaining 23Mixed 25Stacking 24Stand alone 23 Configuration schemes 23Connections 12 D320PL 12 D D320PL 7, 9, 11, 15, 31 Dimensions 9Functionality 7Input modules 15Installation 11 Requirements ...
Page 39 - Revision Sheet
Revision Sheet To: Barco nv Events/Documentation Noordlaan 5, B-8520 KuurnePhone: +32 56.36.89.70, Fax: +32 56.36.88.24E-mail: [email protected], Web: www.barco.com From: Date: Please correct the following points in this documentation ( R5976470/01 ): page wrong correct R5976470 D320PL D IG...
