Page 5 - Table of contents; TABLE OF CONTENTS
Table of contents TABLE OF CONTENTS 1. Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1 Important Safety Instruc...
Page 9 - General functionality; Overview; Display
2. Introduction 2. INTRODUCTION Overview • General functionality • Order info DMP-100 processor • Content of a DMP-100 package • Technical summary • Dimensions of the DMP-100 processor • Components of the DMP-100 processor 2.1 General functionality Overview The DMP-100 is a video processing device, ...
Page 10 - Order info DMP-100 processor; Content of a DMP-100 package; Package; What’s inside of packaging
2. Introduction 2.2 Order info DMP-100 processor Order info: Article number Description R9828833 DMP-100 processor 2.3 Content of a DMP-100 package Package 1 2 3 4 Image 2-31 Protective cover for the DMP-100 processor and installation manual. 2 Cover. 3 Container for all cables and accessories. 4 DM...
Page 11 - Technical summary; Summary
2. Introduction 2.4 Technical summary Summary Type Value Input DVI input (supported resolutions 800x600 / 1024x768 / 1600x1200) Compatibility Barco DVI based LED walls, S10XP FX or newer (Barco NNI tiles are not supported) Output DVI-A, Barco LED protocol. (supported resolutions 800x600@60HZ / 1024x...
Page 12 - Dimensions of the DMP-100 processor; Components of the DMP-100 processor; Component overview
2. Introduction 2.5 Dimensions of the DMP-100 processor Dimensions of the DMP-100 processor 110 mm 250 mm 266 mm 110 mm 250 mm 262.4 mm 56 mm 1.5 mm Image 2-4 2.6 Components of the DMP-100 processor Component overview 1 2 3 4 5 6 Image 2-51 Front side of the DMP-100 processor, including all connecti...
Page 15 - Physical installation of the DMP-100 processor; PROCESSOR; Installation requirements; Requirements
3. Physical installation of the DMP-100 processor 3. PHYSICAL INSTALLATION OF THE DMP-100 PROCESSOR Overview • Installation requirements • Connections of the DMP-100 processor 3.1 Installation requirements Requirements • The DMP-100 processor should not be placed in a built-in installation or enclos...
Page 16 - Connections of the DMP-100 processor; Front panel connections
3. Physical installation of the DMP-100 processor 3.2 Connections of the DMP-100 processor Front panel connections 1 2 3 4 5 6 7 8 9 10 11 Image 3-2 Nr. Connector Description 1 USB interface Common USB interface for the embedded PC. 2 USB — UART interface USB interface for external control PC which ...
Page 19 - Cables; List with available cables
4. Cables for the DMP-100 processor 4. CABLES FOR THE DMP-100 PROCESSOR 4.1 Cables List with available cables Article number Description Image Z3499213 Used to connect a LED-WALL and a Barco display. (T-16/TF-16/SP-20/S14/T20/TF-20/SLITE/S10XP) Image 4–1 R326103 Power cable with CEE7 plug. (used in ...
Page 22 - Embedded PC operating system, settings; What should be done ?; Set the display resolution
5. Embedded PC W ARNING : The Play PC is always used as default. If the Play PC does not exist or has been damaged, the DMP-100 processor will automatically use the embedded PC as a back up solution. If the play PC has beendamaged, a noti fi cation will be given by the used control software. If the ...
Page 23 - Disable the write cache of the disk
5. Embedded PC Or,click Start → Control panel . From the Classic View of that panel, double click on Date and Time . Image 5-3 2. Click on Time Zone tab. 3. Click on the drop down list to select the time zone that corresponds to the time zone where the DMP-100 is being installed. 4. Click on Date &a...
Page 24 - Speci
5. Embedded PC Image 5-4 3. Click on the Hardware tab (2). 4. Make sure the disk drive corresponding to the C: drive is selected in the All disk drives section (3). 5. Click Properties (4). 6. Click on the Policies tab (6). 7. Uncheck the Enable write caching on the disk box (7). 8. Click OK , then ...
Page 25 - Ethernet interface
5. Embedded PC Enhanced IDE interface ICH7M support Single, independent IDE signal channel Supports one CF device Serial ports Two serial RS-232 ports, COM1(RS-232), DB-9 COM2(RS-232/422/485) Parallel port 26-pin fl at-cable connector Keyboard / mouse connector PS/2 Keyboard and Mouse interface Conn...
Page 27 - Configuration scheme; CONFIGURATION SCHEME; Scheme; different con; How to set up the remote control con
6. Configuration scheme 6. CONFIGURATION SCHEME 6.1 Overview Scheme DVI input Formated Video Data SOURCE 1 OptionalControl PC DMP-100 Display SOURCE 2 Remote controlthrough TCP/IP * * ** Image 6-1* The fi berlink is optional. ** Default connection. *** Optional connection for maintenance reasons. A ...
Page 28 - How to connect a laptop to locally control the DMP-100 processor?
6. Configuration scheme Image 6-3 3. Turn on the power of the DMP-100. Note: The Led’s indicated with “PWR” and “MCU” will light up. 4. Use the REAL VNC application on the remote PC to login to the embedded PC. 5. Use the RMS control software to communicate with the DMP-100 processor. W ARNING : The...
Page 31 - RMS; Flashloader; General introduction; Downloading Flash loader; How to download Flash loader?; Using Flash loader; How to use Flash loader
7. Control software 7. CONTROL SOFTWARE 7.1 RMS General introduction RMS control software is running on the embedded PC inside DMP-100 to con fi gure and control the DMP-100 and associated LED wall from basic set-up to advanced features such as input timing, brightness control setup and monitoring t...
Page 33 - Cleaning the cabinet; Necessary tools
8. Maintenance 8. MAINTENANCE 8.1 Cleaning the cabinet C AUTION : Do not use liquid cleaners or aerosol cleaners. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since these will damage the cabinet. Necessary tools Damp cloth. How to clean the cabinet 1. Unplug the DMP-1...
Page 35 - Environmental information; ENVIRONMENTAL INFORMATION; Disposal information; Disposal Information
9. Environmental information 9. ENVIRONMENTAL INFORMATION 9.1 Disposal information Disposal Information This equipment has required the extraction and use of natural resources for its production. It may contain hazardous substances forhealth and environment. In order to avoid the dissemination of th...
Page 37 - Revision Sheet
Revision Sheet To: Barco nv Media & Entertainment Division/Documentation Noordlaan 5, B-8520 KuurnePhone: +32 56.36.82.11, Fax: +32 56.36.88.24Support: www.Barco.com/esupport, Web: www.barco.com From: Date: Please correct the following points in this documentation ( R59770263/06 ): page wrong co...