Page 2 - kçíáÅÉ
ii LED-PRO • User’s Guide ibaJmol= =rëÉêÛë=dìáÇÉ `çéóêáÖÜí © Barco, Inc. May 1, 2006 All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of Barco. kç...
Page 5 - LED-PRO • User’s Guide; Note
LED-PRO • User’s Guide v qÉêãë=få=qÜáë=j~åì~ä=~åÇ=bèìáéãÉåí=j~êâáåÖ= t^okfkd Highlights an operating procedure, practice, condition, statement, etc., which, if not strictly observed, could result in injury to or death of personnel. `^rqflk The exclamation point within an equilateral triangle is inte...
Page 6 - The table below lists the changes to the LED-PRO User’s Guide.; Rev; What’s New in Firmware Version
vi LED-PRO • User’s Guide `Ü~åÖÉ=eáëíçêó The table below lists the changes to the LED-PRO User’s Guide. Table 0-1. Change History Rev Date ECO # Description Approved By A 8/1/05 1478 Release Jim Wickenhiser B 5/1/06 1620 Change summary: • Added new features including Setup Wizard, Input Wizard, diag...
Page 8 - Table of Contents
viii LED-PRO • User’s Guide Table of Contents Bootup with a Stored LOGO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Quick Setup and Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Menu Tree . . . . . . . . . . . . . . . . . . . . . . . ....
Page 13 - fåÇÉñ
LED-PRO • User’s Guide xiii Table of Contents EFVFP nn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 EFVSYNC nn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 EFVRATE nnn.n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 20 - must; Link; Important
6 LED-PRO • User’s Guide NK==fåíêçÇìÅíáçå Features • Test Pattern — Diagonal Scrolling Mode This new feature enables users to enable “diagonal scrolling” of any selected test pattern. In Chapter 4, refer to the “ Using the Test Pattern Menu ” section on page 93 for details. • LED Menu This improved ...
Page 21 - Connectivity Diagram
LED-PRO • User’s Guide 7 NK==fåíêçÇìÅíáçå Connectivity Diagram `çååÉÅíáîáíó=aá~Öê~ã The figure below provides a sample connectivity diagram: Figure 1-1. LED-PRO System Diagram (sample) Please note the following points regarding the diagram: • The maximum of four inputs are shown, one each in RGB, DV...
Page 22 - Application Questions; Contact Information; ” on page 161 for details.
8 LED-PRO • User’s Guide NK==fåíêçÇìÅíáçå Application Questions ^ééäáÅ~íáçå=nìÉëíáçåë At Barco, we take pride in offering unique solutions to demanding technical problems. If you have application questions, require further information or would like to discuss your application requirements in more de...
Page 24 - Hardware Orientation; Display Section
10 LED-PRO • User’s Guide 2. Hardware Orientation LED-PRO Front Panel ibaJmol=cêçåí=m~åÉä The figure below illustrates the LED-PRO front panel: Figure 2-1. LED-PRO Front Panel Following are descriptions of each front panel section: 1) Display Section The Display Section includes the display, the ADJ...
Page 25 - Menu Tree; I n p u t W i z a r d
LED-PRO • User’s Guide 11 2. Hardware Orientation LED-PRO Front Panel aáëéä~ó=pÉÅíáçå The figure below illustrates the Display Section : Figure 2-2. Display Section Descriptions of each button and control are provided below: • The Menu Display is a 4 line x 20 character Vacuum Fluorescent Display (V...
Page 27 - About the LOGO
LED-PRO • User’s Guide 13 2. Hardware Orientation LED-PRO Front Panel fåéìíë=pÉÅíáçå The figure below illustrates the Inputs Section : Figure 2-5. Inputs Section Descriptions of each button and control are provided below: • 1 — selects universal input 1 (the rear panel DVI connector) as the LED wall...
Page 28 - Logo
14 LED-PRO • User’s Guide 2. Hardware Orientation LED-PRO Front Panel ^Äçìí=íÜÉ=ildl The LOGO button can be thought of as an additional input video source which can be selected and transitioned in the normal manner. The button allows you to capture a still frame from any input ( 1 , 2 , 3 or SD/HD )...
Page 29 - Input Specifications
LED-PRO • User’s Guide 15 2. Hardware Orientation LED-PRO Rear Panel ibaJmol=oÉ~ê=m~åÉä The figure below illustrates the LED-PRO rear panel: Figure 2-1. LED-PRO Rear Panel Following are descriptions of each rear panel connector: 1) Universal Input 1 Two DVI-I connectors are provided for Universal In...
Page 32 - Safety Precautions; Description
18 LED-PRO • User’s Guide 3. Installation Safety Precautions p~ÑÉíó=mêÉÅ~ìíáçåë= For all LED-PRO installation procedures, observe the following important safety and handling rules to avoid damage to yourself and the equipment: • To protect users from electric shock, ensure that the power supplies fo...
Page 33 - lower; User’s Guide
LED-PRO • User’s Guide 19 3. Installation Rack-Mount Installation o~ÅâJjçìåí=fåëí~ää~íáçå LED-PRO units are designed to be rack mounted and are supplied with front rack-mount hardware. Please note the following important points: • Rear rack-mount brackets are available as a kit, and are recommended ...
Page 34 - Power Installation; Warning
20 LED-PRO • User’s Guide 3. Installation Power Installation mçïÉê=`çêÇLiáåÉ=sçäí~ÖÉ=pÉäÉÅíáçå LED-PRO is rated to operate with the following supplies: • Input Power: 100-240 VAC, 47-63 Hz • Power Consumption: 150 watts maximum LED-PRO performs line voltage selection automatically, and no user contr...
Page 35 - SDI Input
LED-PRO • User’s Guide 21 3. Installation Signal Installation páÖå~ä=fåëí~ää~íáçå The figure below illustrates a sample LED-PRO system diagram. Use this figure for reference during the signal installation process. Figure 3-2. LED-PRO System Diagram (sample) Use the following steps to install signa...
Page 38 - Format Connection Table
24 LED-PRO • User’s Guide 3. Installation Format Connection Table
Page 40 - P r o g r a m L o a d i n g
26 LED-PRO • User’s Guide 4. Operation Control Overview `çåíêçä=lîÉêîáÉï There are several ways to control the LED-PRO: • The front panel is available for status and control using the display, the ADJUST knob and the two menu “navigation” buttons ( SEL and ESC ). In conjunction with other dedicated ...
Page 41 - Using the Status Menu
LED-PRO • User’s Guide 27 4. Operation Power-Up Initialization • Initialization Screen 3 displays the software version that is currently being loaded. Note that the software version changes as upgrades are released. Figure 4-3. Initialization Screen 3 At the conclusion of the boot-up procedure, the ...
Page 42 - S e t t i n g E t h e r n e t; L o a d i n g L o g o
28 LED-PRO • User’s Guide 4. Operation Power-Up Initialization During this process, the following message is shown: Figure 4-6. Initialization Screen — Set IP Address At the conclusion of the boot-up procedure, the Input 1 button will light and the Status Menu is shown. _ççíìé=ïáíÜ=~=píçêÉÇ=ildl Dur...
Page 45 - generally
LED-PRO • User’s Guide 31 4. Operation Using the Menu System rëáåÖ=íÜÉ=jÉåì=póëíÉã This section lists the rules and conventions for using LED-PRO’s menu system. The figure below illustrates a sample menu: Figure 4-9. Test Pattern Menu (sample) Please note the following important rules and convention...
Page 46 - ESC; entire
32 LED-PRO • User’s Guide 4. Operation Using the Menu System • To navigate back up the menu structure, press ESC . Each press takes you back up the menu tree by one level. • The SEL button is also used to answer “ Yes ” to certain menu queries. The ESC button is also used to answer “ No ” to certain...
Page 47 - Quick Function Reference; Page
LED-PRO • User’s Guide 33 4. Operation Quick Function Reference nìáÅâ=cìåÅíáçå=oÉÑÉêÉåÅÉ Use the following table to quickly access the proper menu for a specific function. Both hyperlinks and page numbers are provided. Table 4-1. LED-PRO Quick Function Reference Table How to: Use the Following: Page...
Page 50 - any level
36 LED-PRO • User’s Guide 4. Operation Using the Status Menu rëáåÖ=íÜÉ=pí~íìë=jÉåì The figure below illustrates a sample Status Menu : Figure 4-10. Status Menu (sample) The Status Menu is a “standalone” menu without any sub-menus. In addition, the “cursor” does not appear. • Status Menu Access • Sta...
Page 51 - instead of the format; Lock to Source; O U T
LED-PRO • User’s Guide 37 4. Operation Using the Status Menu pí~íìë=jÉåì=aÉëÅêáéíáçå The Status Menu provides information about the currently selected system input (as determined by the input buttons) and the selected output. If the input is changed, the fields change accordingly. Other pertinent ch...
Page 53 - Using the Setup Menu
LED-PRO • User’s Guide 39 4. Operation Using the Setup Menu rëáåÖ=íÜÉ=pÉíìé=jÉåì The following topics are discussed in this section: • Setup Menu Tree • Setup Menu Description • Programming EDID • Using the Setup Wizard • Using the Input Wizard • Using the Expert Mode Menu
Page 55 - changes
LED-PRO • User’s Guide 41 4. Operation Using the Setup Menu pÉíìé=jÉåì=aÉëÅêáéíáçå The Setup Menu enables you to set up all LED-PRO input, output and system parameters. If desired, all setup information can be stored in non-volatile memory (using the “ Save System State ” function). Once saved, all ...
Page 56 - Using the Setup Wizard; Using the Input Wizard
42 LED-PRO • User’s Guide 4. Operation Using the Setup Menu pÉíìé=táò~êÇ From the Setup Menu , select Setup Wizard to display the Setup Wizard Start Menu which enables you to quickly and conveniently configure an LED wall along with the system’s output. Figure 4-14. Setup Wizard Start Menu Refer to ...
Page 59 - Programming EDID
LED-PRO • User’s Guide 45 4. Operation Using the Setup Menu pÜ~êéåÉëë From the Analog Source Alignment Menu , select Sharpness to adjust the sharpness of the selected input. This selection sets the scaler's sharpening (or softening) value. • The sharpening range extends from -10 (softest) to +10 (sh...
Page 60 - eìÉ
46 LED-PRO • User’s Guide 4. Operation Using the Setup Menu pçìêÅÉ=^äáÖåãÉåí=Ô=paf From the Setup Menu (for an SD-SDI or HD-SDI input source), select Source Alignment to display the SDI Source Alignment Menu . This menu enables you to adjust all aspects of the source’s “visible” parameters. Figure 4...
Page 62 - B r i g h t n e s s
48 LED-PRO • User’s Guide 4. Operation Using the Setup Menu pçìêÅÉ=^äáÖåãÉåí=Ô=asf From the Setup Menu (for a DVI input source), select Source Alignment to display the DVI Source Alignment Menu . This menu enables you to adjust all aspects of the source’s “visible” parameters. Figure 4-18. DVI Sourc...
Page 63 - mêÉëÉíë; any input; Recall; S a v e
LED-PRO • User’s Guide 49 4. Operation Using the Setup Menu mêÉëÉíë From the Setup Menu , select Presets to display the Global Preset Menu , which enables you to store, recall or delete up to 16 Presets (or "Views"). Each Preset is essentially a “global” combination of pan and zoom settings ...
Page 64 - aÉäÉíÉ; P r e s e t 4
50 LED-PRO • User’s Guide 4. Operation Using the Setup Menu 3. Scroll to the Recall line and press SEL . The global Preset is recalled and applied to the selected input. p~îÉ From the Global Preset Menu , select Save to display the Save Preset Menu , which enables you to save the current pan and zoo...
Page 65 - opOPO; Using the Expert
LED-PRO • User’s Guide 51 4. Operation Using the Setup Menu opOPO From the Setup Menu , select RS232 to display the RS232 Menu , which enables you to set the baud rate for the rear panel RS-232 connector. Figure 4-23. RS232 Menu (sample) To set the RS-232 connector’s baud rate: 1. On the Baud line...
Page 67 - no cables; P r o g r a m E D I D
LED-PRO • User’s Guide 53 4. Operation Using the Setup Menu mêçÖê~ããáåÖ=bafa The EDID DVI Input Format Menu enables you to update LED-PRO's preferred EDID resolution. The menu can be accessed from several points within the menu tree, but all programming procedures are identical. EDID (Extended Displ...
Page 71 - I L i t e 3
LED-PRO • User’s Guide 57 4. Operation Using the Setup Wizard 3. Press SEL to launch the wizard and display the Setup Wizard Start Message . Figure 4-32. Setup Wizard Start Message 4. Press SEL to continue. During this interval, LED-PRO will detect the tiles, query the tiles and count the number of ...
Page 72 - V e r t i c a l t i l e s :
58 LED-PRO • User’s Guide 4. Operation Using the Setup Wizard ~ If the system detects “creative” LED tiles, such as MiSPHERE and MiPIX, the message “ Tile type not supported ” will appear. Because these tile types are not supported by the Wizard, please use Director Toolset for setup. 6. From the Wa...
Page 73 - > H o w d o t h e w a l l d a t a
LED-PRO • User’s Guide 59 4. Operation Using the Setup Wizard 8. From the Set Wall Dimensions Menu , the Wall Data Connection Menu appears. Figure 4-36. Wall Data Connection Menu ~ Select Horizontally if cables are connected horizontally. ~ Select Vertically if cables are connected vertically. ~ Sel...
Page 74 - H S i z e
60 LED-PRO • User’s Guide 4. Operation Using the Setup Wizard The figure below illustrates the Rolling Grid Test Menu . Figure 4-38. Rolling Grid Test Menu ~ Select Yes if the grid test pattern rolls smoothly through the picture. Please continue with step 11 . ~ Select No if the grid does not roll s...
Page 75 - Using the Input; W h a t i s t h e p r i m a r y
LED-PRO • User’s Guide 61 4. Operation Using the Setup Wizard 12. Select Next to display the Input Type Menu : Figure 4-40. Input Type Menu (sample) ~ Select PAL if your primary inputs are PAL. ~ Select NTSC/PC if your primary inputs are NTSC or a PC. This completes the Setup Wizard procedure. 13. S...
Page 76 - N e x t
62 LED-PRO • User’s Guide 4. Operation Using the Input Wizard rëáåÖ=íÜÉ=fåéìí=táò~êÇ The Input Wizard allows users to easily setup and align input sources. It automatically detects and re-scales the selected input source to match the physical size of the LED display. Use the following steps to run...
Page 77 - Tip
LED-PRO • User’s Guide 63 4. Operation Using the Input Wizard 5. After selecting the desired input, select Next to display the Position & Size Menu . Figure 4-44. Position and Size Menu (sample) ~ Select H Position and adjust the input to fill the raster box precisely. ~ Select H Size and adjust...
Page 78 - selected input only; O v e r w r i t e F i l e 1
64 LED-PRO • User’s Guide 4. Operation Using the Input Wizard Please note the following important points regarding the gamma curve: ~ If you previously selected (and stored) a custom gamma curve with the Director Toolset , LED-PRO will query the tiles and recognize the curve as “custom.” ~ If you ha...
Page 80 - Using the Expert Mode Menu; From the; to display the; Expert Mode Menu; below illustrates the complete; Expert Mode Menu Tree
66 LED-PRO • User’s Guide 4. Operation Using the Expert Mode Menu rëáåÖ=íÜÉ=bñéÉêí=jçÇÉ=jÉåì The following topics are discussed in this section: • Expert Mode Menu Tree • Expert Mode Menu Description bñéÉêí=jçÇÉ=jÉåì=qêÉÉ From the Setup Menu , select Expert Mode to display the Expert Mode Menu . The...
Page 81 - provides extensive “advanced” system setup functions. A sample
LED-PRO • User’s Guide 67 4. Operation Using the Expert Mode Menu bñéÉêí=jçÇÉ=jÉåì=aÉëÅêáéíáçå The Expert Mode Menu provides extensive “advanced” system setup functions. A sample menu is shown below. Figure 4-50. Expert Mode Menu (sample) Following are descriptions of each menu function: • Input • O...
Page 82 - fåéìí; Input Setup Menu
68 LED-PRO • User’s Guide 4. Operation Using the Expert Mode Menu fåéìí From the Expert Mode Menu , select Input to display the Input Setup Menu for the selected source. A sample menu is shown below. Figure 4-51. Input Setup Menu (sample) Following are descriptions of each menu function: • Input For...
Page 85 - L e f t E d g e
LED-PRO • User’s Guide 71 4. Operation Using the Expert Mode Menu • Sample Phase — enables you to fine-tune the image by adjusting the sample clock phase. Please note: ~ The adjustment range is -16 to 15. ~ Zero is the default setting. ~ The value is initially filled in by the Auto Config command, o...
Page 86 - qóéÉ; Source Alignment — Analog
72 LED-PRO • User’s Guide 4. Operation Using the Expert Mode Menu qóéÉ From the Input Setup Menu , select Type to choose among the possible signal types available at the current input channel. Please note: • Values are: RGB, YPbPr, NTSC/PAL/SECAM, SDI, and DVI. • When “ In Auto Acquire ” is enabled,...
Page 87 - not
LED-PRO • User’s Guide 73 4. Operation Using the Expert Mode Menu The figure below illustrates the Custom Input Formats Menu : Figure 4-54. Custom Input Formats Menu (sample) Following are descriptions of each menu function: • Custom Format — enables you to select a custom format. The choices consis...
Page 89 - S a v e C u s t o m F o r m a t ?
LED-PRO • User’s Guide 75 4. Operation Using the Expert Mode Menu ~ If the selected format is the current input format in use, or the input format currently saved in an input configuration, the “ Input Format In Use ” message will be shown. Press ESC to continue. • H Total — enables you to adjust (i...
Page 90 - iÉííÉêÄçñ
76 LED-PRO • User’s Guide 4. Operation Using the Expert Mode Menu ^ëéÉÅí=o~íáç From the Input Setup Menu , select Aspect Ratio to display the Input Aspect Ratio Menu . This menu enables you to set the input source’s aspect ratio to a predefined or custom ratio. LED-PRO selects and displays the sourc...
Page 92 - current input; Save Config; identical; Reset Config; identical; Recall Config
78 LED-PRO • User’s Guide 4. Operation Using the Expert Mode Menu ~ When LED-PRO detects Macrovision copy protection on the incoming YPbPr NTSC/PAL video, the value is automatically repositioned to 60mV to account for the reduced amplitude sync pulse. p~îÉ=`çåÑáÖ From the Input Setup Menu , select S...
Page 93 - D e l e t e C o n f i g; S a v e I n p u t C f g ?
LED-PRO • User’s Guide 79 4. Operation Using the Expert Mode Menu aÉäÉíÉ=`çåÑáÖ From the Input Setup Menu , select Delete Config to display the Delete Config Menu , which enables you to delete any input configurations that were previously saved. Figure 4-61. Delete Config Menu (sample) To delete a...
Page 94 - lìíéìí
80 LED-PRO • User’s Guide 4. Operation Using the Expert Mode Menu lìíéìí From the Expert Mode Menu , select Output to display the LED Output Menu which enables you to configure the LED-PRO output. Figure 4-63. LED Output Menu Following are descriptions of each menu function: • Timing Adjust • Refres...
Page 96 - LED
82 LED-PRO • User’s Guide 4. Operation Using the Expert Mode Menu iba=`çåíêçä From the LED Output Menu , select LED Control to choose whether the Barco LED wall is controlled by LED-PRO or by an external application such as Director Toolset . • When set to Remote , the Director Toolset GUI has full ...
Page 97 - D i s a b l e; O n
LED-PRO • User’s Guide 83 4. Operation Using the Expert Mode Menu içÅâ=íç=pçìêÅÉ From the LED Output Menu , select Lock to Source to display the Lock To Source Menu , which enables you to set “lock to source” parameters: Figure 4-65. Lock to Source Menu In order to eliminate video processing delay a...
Page 98 - one; S a v e O u t p u t C f g ?
84 LED-PRO • User’s Guide 4. Operation Using the Expert Mode Menu • Enable the “minimum delay” mode when an another image processor (such as an Encore or ScreenPRO-II) is used to process the video and create multiple windows. The external processor then feeds LED-PRO in a progressive 800x600 format....
Page 99 - bÑÑÉÅíë; Trans With; B l k F a d e; In Auto Acquire
LED-PRO • User’s Guide 85 4. Operation Using the Expert Mode Menu bÑÑÉÅíë From the Expert Mode Menu , select Effects to display the Effects Menu which enables you to select the transition effect that is used when switching between input channels. Figure 4-68. Effects Menu (sample) Following are desc...
Page 100 - içÖç; Capture Logo; D e l e t e L o g o; Freeze
86 LED-PRO • User’s Guide 4. Operation Using the Expert Mode Menu içÖç From the Expert Mode Menu , select Effects to display the Logo Menu , which enables you to save and delete a LOGO. LED-PRO stores one logo in non-volatile memory. Figure 4-69. Logo Menu Following are descriptions of each menu fun...
Page 101 - cêÉÉòÉ
LED-PRO • User’s Guide 87 4. Operation Using the Expert Mode Menu få=^ìíç=^ÅèìáêÉ From the Expert Mode Menu , scroll to the In Auto Acquire function to enable or disable the automatic input acquisition (auto-acquire) function. Press SEL , use the knob to select the desired mode, then press SEL to ac...
Page 102 - póëíÉã
88 LED-PRO • User’s Guide 4. Operation Using the Expert Mode Menu póëíÉã From the Expert Mode Menu , select System to display the System Menu , which enables you to adjust a variety of system parameters, such as the display brightness, Ethernet and Diagnostic RS-232 settings, and panel lock. Figure ...
Page 103 - LED-PRO Remote Commands; bíÜÉêåÉí
LED-PRO • User’s Guide 89 4. Operation Using the Expert Mode Menu Following are descriptions of all menu functions: • Baud — selects the baud rate. Values are: 1200, 2400, 9600, 19200, 38400. • Parameters — select from the following values: N81, E71, O71, E72, O72. • Handshaking — select from the fo...
Page 104 - G W; prior to
90 LED-PRO • User’s Guide 4. Operation Using the Expert Mode Menu • Set Static IP — select the Set Static IP function to display the SET IP Menu . This menu enables you to manually set a subnet mast, gateway, and static IP address when a DHCP server is not available. The menu is only accessible when...
Page 105 - F r o n t P a n e l
LED-PRO • User’s Guide 91 4. Operation Using the Expert Mode Menu To communicate with LED-PRO via Ethernet: a. Ensure that all Ethernet setup is complete b. On a Microsoft ® Windows ® PC, open a command prompt window and type the following and press ENTER : > telnet xxx.xxx.xxx.xxx 10001 ... wh...
Page 106 - LOCKOUT; Factory Reset; S a v e S y s t e m C f g ?
92 LED-PRO • User’s Guide 4. Operation Using the Expert Mode Menu To unlock the panel via the command line interface: 1. Use the LOCKOUT command. In Appendix B, refer to the “ LOCKOUT ” section on page 156 for details. p~îÉ=póëíÉã=pí~íÉ On the System Menu , scroll to the Save System State function...
Page 107 - Test Pattern Menu
LED-PRO • User’s Guide 93 4. Operation Using the Test Pattern Menu rëáåÖ=íÜÉ=qÉëí=m~ííÉêå=jÉåì The following topics are discussed in this section • Test Pattern Menu Tree • Test Pattern Menu Description qÉëí=m~ííÉêå=jÉåì=qêÉÉ Press TEST PAT to access the Test Pattern Menu . The figure below illustra...
Page 110 - P a n V
96 LED-PRO • User’s Guide 4. Operation Using the Pan & Zoom Menu m~å=C=wççã=jÉåì=aÉëÅêáéíáçå The Pan & Zoom Menu allows you to pan, tilt and zoom a selected input, and save the results in a local “Preset” — an internal file held in non-volatile memory for the specific input only. For example...
Page 112 - Using the LED Menu; Press; to access the; LED Menu; . The figure below illustrates the complete menu tree
98 LED-PRO • User’s Guide 4. Operation Using the LED Menu rëáåÖ=íÜÉ=iba=jÉåì The following topics are discussed in this section • LED Menu Tree • LED Menu Description iba=jÉåì=qêÉÉ Press LED to access the LED Menu . The figure below illustrates the complete menu tree — including sub-menus. Figure 4-...
Page 115 - T i l e C o u n t
LED-PRO • User’s Guide 101 4. Operation Using the LED Menu iba=fåÑçêã~íáçå From the LED Menu , select LED Information to display the LED Information Menu , which displays data about the LED wall and fiber communications (if utilized). All menu items are “read only,” and can not be adjusted. Figure 4...
Page 116 - pçìêÅÉ
102 LED-PRO • User’s Guide 4. Operation Using the LED Menu cáÄÉê=qñ=fa The Fiber Tx field lists the ID of the Fiberlink Transmitter . cáÄÉê=oñ=fa The Fiber Rx field lists the ID of the Fiberlink Receiver . iba=qÉëí=m~ííÉêå From the LED Menu , select LED Test Pattern to display the Wall Test Pattern ...
Page 120 - does not
106 LED-PRO • User’s Guide 4. Operation Using the Input Position Menu fåéìí=mçëáíáçå=jÉåì=aÉëÅêáéíáçå The Input Position Menu allows you to perform an abbreviated set of input setup functions, for operator convenience. For a complete set of input setup functions, use the Input Setup Menu in the Expe...
Page 121 - S a v e C o n f i g
LED-PRO • User’s Guide 107 4. Operation Using the Input Position Menu s=mçëáíáçå On the Input Position Menu , select V Position to adjust (in lines) the start of the input video's active area from V sync. s=páòÉ On the Input Position Menu , select V Size to adjust (in lines) the size of the active a...
Page 122 - Delete Config
108 LED-PRO • User’s Guide 4. Operation Using the Input Position Menu 5. To save the input configuration under the selected filename, scroll to the Save Config line and press SEL . ~ If the selected filename has never been used, the message " Config Saved " appears. ~ If the filename is alre...
Page 123 - R e c a l l C o n f i g
LED-PRO • User’s Guide 109 4. Operation Using the Input Position Menu oÉÅ~ää=`çåÑáÖ From the Input Position Menu , select Recall Config to display the Recall Config Menu , which enables you to recall input configurations that were previously saved for the currently selected input format and type. Fi...
Page 124 - Using the Input Position Menu
110 LED-PRO • User’s Guide 4. Operation Using the Input Position Menu
Page 126 - Upgrading Software; Diagnostics; COM
112 LED-PRO • User’s Guide 5. Upgrading Software Software Upgrade Overview pçÑíï~êÉ=réÖê~ÇÉ=lîÉêîáÉï Firmware files for the LED-PRO system are loaded into the hardware at power-up. These files are stored in the unit’s onboard flash memory, which can be upgraded using a serial connection to a PC (or ...
Page 127 - Via FTP Site
LED-PRO • User’s Guide 113 5. Upgrading Software Downloading Software açïåäç~ÇáåÖ=pçÑíï~êÉ Two different methods can be used to download LED-PRO software and the Flash File Loader utility: • Via FTP Site • Via Web Site sá~=cqm=páíÉ Barco Folsom's FTP site address is: ftp.folsom.com To download fro...
Page 129 - P a r a m e t e r s
LED-PRO • User’s Guide 115 5. Upgrading Software Serial Upgrade Method • TXD and RXD should be green. They will flash if Enter is pressed. Figure 5-2. Flash Loader Status Lights, Normal Condition c. Press Enter a few times to display the system prompt “ # ” on screen. d. If the prompt does not appea...
Page 130 - S O F T W A R E V E R S I O N
116 LED-PRO • User’s Guide 5. Upgrading Software Serial Upgrade Method 14. On LED-PRO, perform a factory reset. Press SETUP , select Factory Reset , and then confirm. In Chapter 4, refer to the “ Factory Reset ” section on page 52 for additional details. 15. On LED-PRO, verify that the new software ...
Page 132 - Parameter
118 LED-PRO • User’s Guide ^K==péÉÅáÑáÅ~íáçåë Input Specifications fåéìí=péÉÅáÑáÅ~íáçåë= The table below lists LED-PRO input specifications. * All buffered loop-through connectors, 75 Ohm output impedance Table A-1. LED-PRO Input Specifications Parameter Detail Specification Video Input Universal In...
Page 133 - Output Specifications
LED-PRO • User’s Guide 119 ^K==péÉÅáÑáÅ~íáçåë Output Specifications lìíéìí=péÉÅáÑáÅ~íáçåë The table below lists LED-PRO output specifications. rëÉê=`çåíêçä=péÉÅáÑáÅ~íáçåë The table below lists LED-PRO user control specifications. mÜóëáÅ~ä=~åÇ=bäÉÅíêáÅ~ä=péÉÅáÑáÅ~íáçåë= The table below lists LED-PRO ...
Page 134 - Communications Specifications
120 LED-PRO • User’s Guide ^K==péÉÅáÑáÅ~íáçåë Communications Specifications `çããìåáÅ~íáçåë=péÉÅáÑáÅ~íáçåë= The table below lists LED-PRO communications specifications. * 115k Baud recommended for LED tile firmware upload only. * 19.2k Baud recommended for normal operation, such as Director Toolset. ...
Page 135 - Pinouts; Analog 15-pin D Connector; The figure below illustrates the analog 15-pin D connector:; Pin
LED-PRO • User’s Guide 121 ^K==péÉÅáÑáÅ~íáçåë Pinouts máåçìíë= The following topics are discussed in this section: • Analog 15-pin D Connector • DVI-I Connector Pinouts • Ethernet Connector • Serial and Diagnostic Connector ^å~äçÖ=NRJéáå=a=`çååÉÅíçê The figure below illustrates the analog 15-pin D c...
Page 140 - Diagnostics Port
126 LED-PRO • User’s Guide _K==oÉãçíÉ=`çåíêçä=mêçíçÅçä Default Serial Parameters aÉÑ~ìäí=pÉêá~ä=m~ê~ãÉíÉêë Default serial communications parameters are provided for the following two ports: • Diagnostics Port • RS-232 Port Please note: • The system returns to these values after a factory reset. • Th...
Page 141 - Command
LED-PRO • User’s Guide 127 _K==oÉãçíÉ=`çåíêçä=mêçíçÅçä Default IP Address aÉÑ~ìäí=fm=^ÇÇêÉëë The LED-PRO default IP address is 192.168.000.200 . Please note: • The system returns to this value after a factory reset. • This default address can be changed using the menu system. In Chapter 4, refer to ...
Page 149 - obpe; : All available resolutions in the format:
LED-PRO • User’s Guide 135 _K==oÉãçíÉ=`çåíêçä=mêçíçÅçä LED-PRO Remote Commands ibaJmol=pÉêá~ä=`çãã~åÇ=aÉëÅêáéíáçåë obpe • Description : Query the available resolution list for the LED-PRO. • Parameters : None • Returns : All available resolutions in the format: n : HxV @F (example: 20 : 1024x768 @59...
Page 159 - fpeom
LED-PRO • User’s Guide 145 _K==oÉãçíÉ=`çåíêçä=mêçíçÅçä LED-PRO Remote Commands S IVREC 1 (Recalls Input Channel View of channel 1) fsp^s=áå • Description : Input Channel View (Preset) Save • Parameters : in - Input chnl [1-4] S IVSAV 1 (Saves the Input Channel View for channel 1) i`h\=áå • Descripti...
Page 169 - obpbq
LED-PRO • User’s Guide 155 _K==oÉãçíÉ=`çåíêçä=mêçíçÅçä LED-PRO Remote Commands • Returns : MAC address. xx:xx:xx:xx:xx:xx S EMAC? (Queries for Ethernet MAC address) p_^ra=å • Description : Adjust the Serial Baud Rate. • Parameters : n - Serial baud rate: n[0-4] 1200 | 2400 | 9600 | 19200 | 38400 • Q...
Page 172 - sfbtfo; A “View” is synonymous with “Preset.”
158 LED-PRO • User’s Guide _K==oÉãçíÉ=`çåíêçä=mêçíçÅçä LED-PRO Remote Commands vvv.v - Vertical Pan (-100.0% - +100.0%) sfbta=åå • Description : Delete saved View (Preset) • Parameters : nn - View Index [1 - 15] S VIEWD 1 (Delete View 1.) sfbto=åå • Description : Recall View (Preset) • Parameters : ...
Page 173 - Returns the current zoom scale factor in the format
LED-PRO • User’s Guide 159 _K==oÉãçíÉ=`çåíêçä=mêçíçÅçä LED-PRO Remote Commands wllj=åååKå • Description : Selects zoom scale factor (applied both horizontally and vertically. • Parameters : nnn.n - Zoom value [min-max] depends on scale factor • Query : ZOOM? Returns the current zoom scale factor in ...
Page 175 - The following topics are discussed in this Appendix:; Warranty; RMA Conditions are listed below:
LED-PRO • User’s Guide 161 `K==`çåí~Åí=fåÑçêã~íáçå få=qÜáë=^ééÉåÇáñ The following topics are discussed in this Appendix: • Warranty • Return Material Authorization (RMA) • Contact Information t~êê~åíó All video products are designed and tested to the highest quality standards and are backed by a ful...
Page 176 - Barco Media and Entertainment
162 LED-PRO • User’s Guide `K==`çåí~Åí=fåÑçêã~íáçå Contact Information `çåí~Åí=fåÑçêã~íáçå Barco Media and Entertainment 11101 Trade Center DriveRancho Cordova, California 95670USA • Phone: (916) 859-2500 • Fax: (916) 859-2515 • Websites: ~ www.folsom.com ~ www.events.barco.com Sales Contact Informa...
Page 177 - kìãÉêáÅë; Analog source
LED-PRO • User’s Guide 163 fåÇÉñ kìãÉêáÅë 10/100BaseT . . . . . . . . . . . . . . . . . . . . . . . . . . 161-1 sampling . . . . . . . . . . . . . . . . . . . . . . . . . . 691-1 Timing Adjust Menu . . . . . . . . . . . . . . . . . . 7050/60 Hz refresh rate . . . . . . . . . . . . . . . . . . . . . ...
Page 178 - Index; Connectors
164 LED-PRO • User’s Guide Index ` Cable information . . . . . . . . . . . . . . . . . . . . . . 18Capture logo . . . . . . . . . . . . . . . . . . . . . . . . . . 86Change history . . . . . . . . . . . . . . . . . . . . . . . . . . . . visampling mode . . . . . . . . . . . . . . . . . . . . . 70 Ch...
Page 179 - Fiber
LED-PRO • User’s Guide 165 Index DMSG mode . . . . . . . . . . . . . . . . . . . . . . . . . 153Documentation conventions and symbols . . . . . 3Double arrow . . . . . . . . . . . . . . . . . . . . . . . . . . 11Download software . . . . . . . . . . . . . . . . . . . . 113 serial upgrade . . . . . ....
Page 180 - Green
166 LED-PRO • User’s Guide Index overview . . . . . . . . . . . . . . . . . . . . . . . . . . 49recall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49save . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Green brightness, analog source . . . . . . . . . . . . 44contrast, ana...
Page 182 - Menu tree
168 LED-PRO • User’s Guide Index LOGOD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156LOGOI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156LOGOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156LOGOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 183 - Power
LED-PRO • User’s Guide 169 Index Overview, control . . . . . . . . . . . . . . . . . . . . . . . 26Overwrite Custom Format Menu . . . . . . . . . . . 74OVPOS nnnn . . . . . . . . . . . . . . . . . . . . . . . . . 149OVSYNC nnnn . . . . . . . . . . . . . . . . . . . . . . . 149OVTOTAL nnnn . . . . . ...
Page 185 - Tile
LED-PRO • User’s Guide 171 Index description . . . . . . . . . . . . . . . . . . . . . . . . 37fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Support, technical information . . . . . . . . . . . . 162S-Video (Y/C)...
Barco K5960008-03
Manual
Barco R5976476/03
Manual
Barco MFGD 2320
Manual
Barco R5976214
Manual
Barco 1219
Manual
Barco D320PL
Manual
Barco R9843051
Manual
Barco DOC-3200-2
Manual
Barco E-2620
Manual
Barco II
Manual
Barco 16x16
Manual
Barco RCP-120
Manual
Barco MGD 2621
Manual
Barco MXRT2400
Manual
Barco DP100
Manual
Barco DP90
Manual
Barco R5976426
Manual
Barco R5976663/01
Manual