Bakers Pride CA70-CVMP12 - Manuals

Page 2 - TABLE OF CONTENTS

WARRANTYGETTING STARTED OPERATION CARE OF YOUR UNIT TROUBLESHOOTING MAINTENANCE REPLACEMENT PARTS WIRING DIAGRAMS 34 INTRODUCTION 4 MODELS 4 UNPACKING 4 SETTING-UP 5 CLEANING. 56 OPERATING CONTROLS AND COMPONENTS 6 OPERATIONAL PROCEDURES 67 ASSISTANCE 7 SAFETY AND HEALTH 7 CLEANING 7 MODEL SPECIFICA...

Page 3 - BEVLES COMPANY LIMITED WARRANTY

4/02 BEVLES COMPANY LIMITED WARRANTY 729 Third Avenue * Dallas, TX 75226 Phone: +1 (214) 421-7366 Fax: +1 (214) 565-0976 1. Bevles warrants to the original purchaser that on the date the equipment is shipped (sold), it will be free of defects in materials or workmanship. Bevles will, at its discret...

Page 4 - This manual applies to the following models:

2. GETTING STARTED 2-1 INTRODUCTION **NOTE: "NOTE" "WARNING” 2-2 MODELS 2-3 UNPACKING **NOTE: WARNING: NOTE: BEVLES Heated Holding Cabinets are quality built equipment designed to hold prepared foods at a safe temperature (no less than 140°), with or without humidity. These cabinets have...

Page 9 - personnel using only quality BEVLES parts.

Figure 8 Figure 9 Figure 10 6. MAINTENANCE **CAUTION: All maintenance on BEVLES Heating Holding Cabinets should be performed by trained personnel using only quality BEVLES parts. 6-1 REPLACING PARTSAfter using the Troubleshooting table (section 5-2) to determine the solution, refer to the appropriat...

Page 10 - Diagram 1

5. Feed the wires of the replacement indicator lamp module through the opening and snap the new indicator lamp module into place. 6. Reconnect wiring with each of the two new wires going to a different wire nut (it doesn't matter how you match the new module wires). Re-tape over wire nuts and wires....

Page 12 - Diagram 2

6-1h. Replacing the power cord for a CA43. Required: Medium (6”) phillips screwdriver, Medium (6") flathead screwdriver, Wiring markers (color or number codes), Electrical tape , Wiring diagram for CA43(see step 10) 1. Remove the back panel of the module by removing the five phillips head screws...

Page 13 - Diagram 3

Figure 24 Figure 25 Figure 26 Fan Blower (0) (1) (0) (1) Power Indicator Lamp (5) (1) Thermostat Indicator Lamp Power Switch (0) (1) (2) (3) (0) (5) Thermostat Diagram 3 Power Cord (Grd) (2) (3) (4) (1) Heating Element (4) (5) Klixon Thermostat (0) (1) Cooling Fan Figure 27 Figure 28 Figure 29 Figur...

Page 15 - Diagram 5

Fan Blower (0) (1) (0) (1) Power Indicator Lamp (5) (1) Thermostat Indicator Lamp Power Switch (0) (1) (2) (3) (0) (5) Thermostat Diagram 5 Power Cord (Grd) (2) (3) (4) (1) Heating Element (4) (5) Klixon Thermostat (0) (1) Cooling Fan Figure 39 Figure 38 Figure 37 Figure 36 Figure 35 8. Remove the t...

Page 19 - Model Number

7. REPLACEMENT PARTS Use only BEVLES replacement parts in repairing your unit. This assures you of continued high quality performance. To determine the parts you need: 1. Use the drawings found in section 7-5 and refer to the parts list in section 7-6 to determine the BEVLES part numbers you need. 2...

Page 29 - WIRING DIAGRAMS AND OTHER TECHNICAL DATA

1 1A 1B 2 2A 3 3A 5 5A 6 7 8 9 10 11 12 13 17 19 20 21 22 23 23A 24 24A 25 25A 26 27 28 29 30 31 32 33 34 35 36 37 20068 20132 20140 20072 20074 20076 20124 20080 20082 50132 50140 50736 70073 50392 50400 50720 83044 20084 83008 70257 83100 41041 83180 84028 50744 50818 50744 50818 50810 70276 80036...

Page 30 - IMPORTANT FOR FUTURE REFERENCE

30 Notes: IMPORTANT FOR FUTURE REFERENCE Please complete this information and retain this manual for the life of the equipment. For WARRANTY SERVICE and/or PARTS, this information is required. Model Number Serial Number Date Purchased

Page 32 - BevLes; Innovative Foodservice Equipment Custom

Phone: +1 Fax: +1 (214) 565-0976 Toll Free: +1 (800) 441-1601 Website: www.BevLes.com E-mail: [email protected] (214) 421-7366 BevLes 729 Third Avenue Dallas, TX 75226 Innovative Foodservice Equipment Custom Designed for Performance, Service and Value. 32