Audiovox XTM-600 - Manuals - manualsarea.com

Page 2 - INDEX

Specifications.....................................................................3Precautions........................................................................ 4Installation Instructions...................................................... 5Wiring Instructions..................................

Page 3 - Saturday; SPECIFICATIONS

Filter type: Selectable Full/Low-passCrossover @ 18dB/Octave Filter Crossover: LPF 50-250 Hz (variable)HPF 50-250 Hz (Variable) Bass Boost Level: 0 - 18dB (Variable) Bass Boost Frequency: 40 - 80Hz (Variable) Supply Voltage: 12 volts, negative ground Fuse Rating: 20 amps. Dimensions (W X H X D): 295...

Page 4 - must; PRECAUTIONS

1. Although this unit is designed with built-in self-protection circuits, there may be a possibility of damage if it is not wired correctly. Please follow the wiring instructions carefully for the type of system being used. 2. The last lead to be connected is the wire to the positive( ) terminal of ...

Page 5 - CHECK BEFORE YOU DRILL!; Secure the amplifier to the mounting surface using; INSTALLATION INSTRUCTIONS

1. Select a mounting area where the amplifier will have sufficient air circulation for proper cooling.Inadequate air circulation will cause the temperatureof the amplifier to rise and will trigger the thermalprotection mode. 2. Place the amplifier on the mounting surface and mark the locations of th...

Page 6 - WIRING INSTRUCTIONS

The wiring of your amplifier will depend on the system and speakers you are using but will either be a stereo, mono, ormixed-mono application. The following pages illustrate the input and output wiring for these types. please refer to theappropriate diagrams for the system configuration you are usin...

Page 7 - Speaker Connections; ground any speaker leads to the chassis of the vehicle.; DO NOT; use both input levels at the same time.

4. Speaker Connections Depending on the type and number of speakers used with the amplifier, wire them to the speaker terminals as per the appropriate wiring diagram. For most applications, #16 gauge wire should be used for the speaker leads but in no case thinner than #18 gauge. For leads in excess...

Page 8 - INPUT WIRING DIAGRAM

HI-INPUT HI-INPUT GND GND L + L + R + R + LL RR RR LL PWR PWR PRT PRT MIN MIN MAX MAX GAIN GAIN 40Hz 40Hz 80Hz 80Hz BASS BOOST FRQ BASS BOOST FRQ X-OVER X-OVER LPF LPF FULL FULL CAR STEREO White Green Black Brown Gray HIGH-LEVEL (SPEAKER) INPUT(WIRE SIDEVIEW) LOW-LEVEL INPUT Right Speaker Left Speak...

Page 9 - BATTERY; OUTPUT WIRING DIAGRAM

CAR STEREO GROUND BATTERY FOR 12 VOLT USE ONLY AUTO-ANTENNA LEAD GROUND METALSECTION OF VEHICLE EXISTING SCREW OR BOLT CLEAN PAINT, RUST, DIRTOR GREASE FROM AREA FOR GOOD CONNECTION. SPEAKER2(MONO) 2-8 OHM SPEAKER REM BATT GND FUSE FUSE -9- OUTPUT WIRING DIAGRAM USE #10 GAUGEWIRE (SEE TEXT)

Page 10 - OPERATION

-10- Power Indicator Lamps The Power Indicator Lamps will light to indicate that the unit is connected to the battery and that the RemoteTurn-On terminal is receiving +12 volts, thus turningon the amplifier Protection Mode LED The LED illuminates red to indicate that the self-protection circuits hav...

Page 11 - Sub-Woofer Crossover Selector; below; L P F C r o s s o v e r F r e q u e n c y C o n t r o l

If, however, there is still output from the amplifier when the car stereo volume control is at its minimum setting, or the output level increases too fast with a small rotation of the volume control, adjust the Level control to decrease the output from the system.Once the correct setting is found, t...

Page 13 - Printed in Korea

2003 Audiovox Electronics Corporation, Hauppauge, N.Y. C C Printed in Korea 128-6558