Audiovox XM-RCV - Manuals - manualsarea.com

Page 3 - INSTALLATION and WIRING PRECAUTIONS; battery cable, prior to installation. Connect power wires last.; Do not install the unit in the following locations:; the supplied brackets and screws.; Be careful not to damage the car wiring.

INSTALLATION and WIRING PRECAUTIONS 3 1. To prevent a short-circuit, Be sure to turn off the ignition and remove the negative (-) battery cable, prior to installation. Connect power wires last. NOTE: If the SRXM-001 System is to be installed in a car that is equipped with an on-boarddrive or navigat...

Page 4 - INSTALLATION PARTS; SRXM-001 MAIN SYSTEM COMPONENTS; PACKING LIST; SATELLITE SYSTEM CONTROL; SUPPLIED

Satellite Radio Wireless Remote Control Model #SAT-RC Self-tapping Screws (5mm x 15mm) , with Flat Washers and Lock Washers (Used to mount RRU to mounting surface) FM Modulator Control Interface Wire Harness 1 pc. (P/O SAT-COM) 4 Phillips Round Head Screw (4mm x 8mm) w/ External Tooth Washer (Used t...

Page 5 - TYPICAL FM MODULATED SYSTEM

A U DIO O X SF T 4 7 1 6 5 8 0 9 23 SA TEL L ITE R A D IO R F M O D U L A T O R TO S C U AU D IO O X AN T . T O R ADI O TO C A R AN T . R L T O RRU POW ER A U D IO O X TER . SA T. D IN OUT AU DI O O U T R L 5 TYPICAL FM MODULATED SYSTEM INSTALLATION NOTE: “A” To Satellite Radio Antenna (Sold separat...

Page 7 - MOUNTING THE FM MODULATOR

7 TYPICAL FM MODULATED INSTALLATION forSRXM-001 SYSTEM COMPONENT LAYOUT MOUNTING THE FM MODULATOR Install the FM Modulator to the mounting surface with theself-tapping screws (4mm x 12mm). Self-TappingPhillips HeadScrew Ground (BLACK)Attach this wire to the chassis of the car. Besure that the surfac...

Page 8 - PROCEDURE for HORIZONTAL INSTALLATION of the RRU; SYSTEM INSTALLATION; WARNING

PROCEDURE for HORIZONTAL INSTALLATION of the RRU SYSTEM INSTALLATION 3. RADIO RECEIVER UNIT (RRU) 2. Determine the mounting location and drill 4x 1/8” (4mm) mounting holes. NOTE: If mounting surface is carpeted, use caution when drilling holes to prevent drill bit fromcatching on carpet. Cut holes i...

Page 9 - PROCEDURE for VERTICAL INSTALLATION of the RRU

Attach a mounting bracket to each side of the RRU, using the 4 Phillips Round HeadScrews (4mm x 8mm). Mount the unit in place, using 4 Self-tapping Screws (5mm x 15mm), w/Flat Washers and LockWashers. Use RTV (silicone sealer) on screw threads or around the holes to prevent moistureintrusion. 3. 9 1...

Page 10 - PROCEDURE for the MOUNTING of the RRU UNDER THE REAR DECK

Determine the mounting location and drill four 4mm mounting holes. 3. Mount the unit in place, using 4 Self-tapping Screws (5mm x 15mm), w/Flat Washers andLock Washers. 1. Attach the mounting brackets to each side of the RRU, using the 4 Phillips Round HeadScrews (4mm x 8mm). PROCEDURE for the MOUNT...

Page 11 - and the back surface of the SCU.; INSTALLING THE SATELLITE SYSTEM CONTROL UNIT (SCU)

PROCEDURE for a TYPICAL INSTALLATION of the SCU USING HOOK &LOOP ADHESIVE TAPE (SUPPLIED) 1. Determine where the SCU is to be located (flat surface) NOTE: The chosen position must allow a clear view of the display and easy access to the controls for both the Driver and Passengerof the vehicle. 2...

Page 12 - Trim Ring; SCU

12 PROCEDURE FOR A TYPICAL BRACKET INSTALLATION OF THE SCU(Bracket not supplied) © Copyright 2001 Audiovox Electronics Corp. 150 Marcus Blvd. Hauppauge, NY 11788 128-6213A Audiovox suggests this type of installation over the Hook & Loop type of installation though the Hook & Loopinstallation...