Page 2 - Important Notice
Important Notice It is unlawful in most jurisdictions for a person to drive a motor vehicle which is equipped with a television viewer or screen that islocated in the motor vehicle at any point forward of the back of the driver's seat, or that is visible directly or indirectly to the operator of the...
Page 3 - MATERIALS INCLUDED IN THIS PACKAGE:
MATERIALS INCLUDED IN THIS PACKAGE: 1) VOH683 Video Monitor with out TV Tuner / VOH684 or VOH704 Video Monitor with TV Tuner (1 pc)2) Accessory Harness (P/N 8010730) (1 pc)3) 12 Pin Power / Signal harness (P/N 112B2821) (1 pc)4) 2 Pin Power Wire Harness with choke (P/N 112B2824) (1 pc)5) Hardware Pa...
Page 4 - GENERAL INSTALLATION APPROACH:; their respective locations.; GENERAL SYSTEM CONFIGURATIONS:; There are a few audio output options that can be added as follows:
GENERAL INSTALLATION APPROACH: 1) Decide upon system configuration and options that will be installed (i.e.: what components, VCP, Tuner, RF Modulator/external amp, remote headphones, 2 nd VCP, etc.). 2) Review all manuals to become familiar with electrical requirements and hook ups.3) Decide upon m...
Page 5 - FULL SIZE CONSOLE INSTALLATION
VEHICLE PREPARATION: 1) Locate a constant power source (+12v at all times) and an accessory power source (+12v whenkey is in the ACC. and run positions, and 0v when key is off). Generally, these wires can be foundat the ignition switch or fuse-box. 2) The mounting method and location will vary from ...
Page 6 - MINI CONSOLE INSTALLATION:; Lowest point mark
MINI CONSOLE INSTALLATION: This page only covers special installation considerations for the mini-console installation. If the videomonitor is to be installed with a custom full sized overhead console, refer to page 3.If the video monitor is to be installed in a vehicle with the mini console (P/N 10...
Page 7 - MOUNTING THE MINI-CONSOLE
Roof Roof Support Headliner 5"x9"x3/4" PlywoodBlock or OptionalVOHBKT (4) #8x1" self drilling screws (not supplied) Mini-Console Video Unit (4) #8 flat washers (not supplied) (4) #8x3/4" self tapping screws (not supplied) -5- MOUNTING THE MINI-CONSOLE
Page 8 - Figure A; the main PCB and into the Mini-Din Connector on the main PCB.
Figure A 1) Make the connections to the vehicle for the 12 pin wiring harness.2) Remove screws on PCB Cover. Open the cover to gain access to Mini-Din Connector on main PCB.3) Insert the Circular Mini-Din Connector of the source component harness through the wire tie loop on the main PCB and into th...
Page 9 - Figure B; on the main PCB and into the Mini-Din Connector on the main PCB.
Figure B 1) Make the connections to the vehicle for the 12 pin wiring harness.2) Remove screws on PCB Cover. Open the cover to gain access to Mini-Din Connector on main PCB. (Cover will remain attached to rivet hole). 3) Insert the Circular Mini-Din Connector of the source Component Harness through ...
Page 11 - Factory Dome light circuit; Positive Switched Dome lighting; CONNECTING THE DOME LIGHTS
Red / black - Lamp on Black / red - Lamp common Purple / brown - Lamp Auto To 12 pin connector on Monitor To constant +12vdc To constant +12vdc Factory Door ajarswitch or BodyControl computer Factory Dome light circuit Positive Switched Dome lighting -9- CONNECTING THE DOME LIGHTS The dome lights in...
Page 12 - Negative Switched Dome lighting; connector
© Copyright 2001 Audiovox Electronics Corp. 150 Marcus Blvd. Hauppauge, NY 11788 128-6118 Troubleshooting: SYMPTOM: No power at Video Monitor P o w e r b u t n o v i d e o o rsound Picture, but no sound S t a t i c o n T V S t a t i o n s(Tuner Version Only) No FM Radio Stations No Infrared remote f...