Audiovox VOH-641 - Manuals - manualsarea.com

Page 2 - Important Notice

Important Notice It is unlawful in most jurisdictions for a per- son to drive a motor vehicle which is equipped with a television viewer or screen that is located in the motor vehicle at any point forward of the back of the driver's seat, or that is visible directly or indirectly to the operator of ...

Page 3 - MATERIALS INCLUDED IN THIS PACKAGE:

MATERIALS INCLUDED IN THIS PACKAGE: 1) VOH-641 Video Monitor with out TV Tuner / VOH-642 Video Monitor with TV Tuner (1 pc)2) Accessory Harness (P/N 8010730) (1 pc)3) 12 Pin Power / Signal harness (P/N 112B2821) (1 pc)4) 2 Pin Power Wire Harness with choke (P/N 112B2824) (1 pc)5) RCA “Y” Adapter (1 ...

Page 4 - GENERAL INSTALLATION APPROACH:; their respective locations.; GENERAL SYSTEM CONFIGURATIONS:; Notes; wiring diagram on p7.

GENERAL INSTALLATION APPROACH: 1) Decide upon system configuration and options that will be installed (i.e.: what components, VCP, Tuner, RF Modulator/external amp, remote headphones, 2 nd VCP, etc.). 2) Review all manuals to become familiar with electrical requirements and hook ups.3) Decide upon m...

Page 5 - FULL SIZE CONSOLE INSTALLATION

VEHICLE PREPARATION: 1) Locate a constant power source (+12v at all times) and an accessory power source (+12v whenkey is in the acc. and run positions, and 0v when key is off). Generally, these wires can be foundat the ignition switch or fusebox. 2) The mounting method and location will vary from v...

Page 6 - MINI CONSOLE INSTALLATION:; Lowest point mark

MINI CONSOLE INSTALLATION: This page only covers special installation considerations for the mini console installation. If the videomonitor is to be installed with a custom full sized overhead console, refer to page 3.If the video monitor is to be installed in a vehicle with the mini console (part n...

Page 7 - MOUNTING THE MINI CONSOLE

Roof Roof support Headliner 5"x9"x3/4" Plywood Block (4) #8x1" self drilling screws (not supplied) Mini-Console Video unit (4) #8 Flat washers (not supplied) (4) #8x3/4" self tapping screws (not supplied) -5- MOUNTING THE MINI CONSOLE

Page 8 - Note

1) Make the connections to the vehicle for the 12 pin wiring harness.2) Remove screws on PCB Cover. Open the cover to gain access to Mini-Din Connector on main PCB.3) Insert the Circular Mini-Din Connector of the source component harness through the wire tie loop on the main PCB and into the Mini-Di...

Page 9 - on the main PCB and into the Mini-Din Connector on the main PCB.

Antenna Dash Radio Red RCA (Audio Right) IR LED: Clean the IR Receiver Window on the front of the VCP. Remove Adhesive Backing and Apply IR LED to IR Window on the Face of the VCP. Black (Ground) Optional External Speakers Gray (Left+) Green (Right+) Accessory Harness Item# 2 Yellow RCA (Video) Whit...

Page 10 - Positive Switched Dome lighting; CONNECTING THE DOME LIGHTS

Red / black - Lamp on Black / red - Lamp common Purple / brown - Lamp Auto To 12 pin connector on Monitor To constant +12vdc To constant +12vdc Factory Door ajarswitch or BodyControl computer Factory Dome light circuit Positive Switched Dome lighting -8- CONNECTING THE DOME LIGHTS The dome lights in...

Page 11 - Negative Switched Dome lighting

Troubleshooting: Symptom: No power at Video Monitor Power but no video or sound Picture, but no sound Static on TV Stations (TunerVersion Only) No Infrared remote func-tions for VCP (or other com-ponents) Remedy: -Verify +12 VDC on Red wire at 2 pin Power Harness behind video moni-tor. Verify ground...