Audiovox PRO9801N - Manuals

Page 2 - YOUR “CODE HOPPING“ TRANSMITTERS

128-8483 2 of 24 Page 2 Protected Push Button LED Valet/Override Switch 7-Function LED-Arm / Disarm / Zone 1 / Zone 2 / Zone 3 / Valet / Arming Intrusion Alert With Memory Instant Siren Activation When Used Starter Disable Output Additional Engine Immobilizer Output, (Optional Relay Requ...

Page 3 - will not; ARMING THE SYSTEM - ACTIVE

128-8483 3 of 24 Page 3 known as a code grabber, which will receive and store the signal from your keychain transmitter and re-transmit at a later time to disarm your system.Your Keeloq Code Hopping transmitters will change their signal every time the button is pressed, so when a thief grabs then re...

Page 4 - PROTECTION WHILE THE SYSTEM IS ARMED

128-8483 4 of 24 Page 4 ; The dash mounted LED begins to flash slowly. ; Parking Lights flash one time. ; Siren will not sound. If the siren "chirped" three times, sometime after arming, the exclusive delayeddome light learn circuit has been programmed and the system detected a openentry poi...

Page 5 - SILENT DISARMING

128-8483 5 of 24 Page 5 ; Any mild impact to the vehicle’s glass will cause the alarm to sound a short series of warning tones. ; Any strong impact to the vehicle’s glass will cause the alarm to trigger for the full 30 second alarm cycle. NOTE: If the optional interior illumination circuit was insta...

Page 7 - Programming Your Custom Override Code:; sequence. Turn the ignition switch to the on position.; Custom Code Programming Example:

128-8483 7 of 24 Page 7 3. To return to normal operation, press and release the PBLED switch any time the ignition is on. NOTE: Always remember to return the vehicle to the valet off position. This will ensure thatthe vehicle remains protected at all times. MANUALLY OVERRIDING YOUR SYSTEM:USING THE ...

Page 8 - ELIMINATING THE NORMAL ARM/DISARM CHIRPS

128-8483 8 of 24 Page 8 2. Turn the ignition switch to the on position.3. Within 10 seconds, press and release the PBLED switch, 3 times.4. Within 10 seconds turn the ignition switch off, on, off, on, off, on. (The siren or horn will beep and the lights will flash one time.) 5. Within 10 seconds, be...

Page 10 - grammed into your system.; PBLED SAFETY CONTROL SWITCH; serviced. To place the system in the service mode:; REMOTE STARTING THE VEHICLE; occurs. DO NOT remote start the vehicle if it is garaged.; To Remote Start The Vehicle:; the ignition key to the on position.

128-8483 10 of 24 Page 10 2. Within 2 seconds of step 1, press and release the ARM button 2 times, to defeat the pre and full detect stages of the shock sensor. (The lights will flash and the siren will chirp twice.) 3. Within 2 seconds of step 1, press and release the ARM button 3 times to enter th...

Page 13 - TURBO TIMER MODE

128-8483 13 of 24 Page 13 Other Transmitter button configurations are also available. Consult your installa- tion center for other configurations not listed above that may have been programmed to operate a specific feature of your system.This security system has an additional feature that can be con...

Page 14 - TRANSCEIVER ICONS AND THEIR INDICATIONS

128-8483 14 of 24 Page 14 time according to the selection during installation.If you do not want the vehicle to continue to run for one cycle, simply step on thevehicle's brake, or release the parking brake, or activate the transmitter's startbutton two times in succession. Any of these will cause t...

Page 15 - ADDITIONAL ICONS THAT MAY BE DISPLAYED ARE:

128-8483 15 of 24 Page 15 disarmed and the Panic Mode is activated, the lights will flash unlock icon willbe displayed and the siren will beep on the LCD screen. When ever the vehicle is operated from the two way transmitter,the unit will beep responsive to the function executed at thevehicle. 1 bee...

Page 19 - Standing at the vehicle at the time you want it to

128-8483 19 of 24 Page 19 Battery Indicator: Your transmitter has a battery indicator that is shown in the upper rightcorner of the screen as shown left. This icon indicates a new battery shown with 3 bars. As the battery deteriorates, the bars will disap- pear. 1 bar indicates the battery should be...

Page 20 - Temperature Start Mode.; This icon will appear when the temp start

128-8483 20 of 24 Page 20 Temperature Start Mode. This icon will appear when the temp start mode is activated. The vehicle will start one time automatically when the temperature reaches 0*. Caution, Be certain vehicle is outside before activating this mode. To toggle this feature on of off, from the...

Page 22 - THIS PAGE LEFT BLANK INTENTIONALLY

128-8483 22 of 24 Page 22 THIS PAGE LEFT BLANK INTENTIONALLY

Page 23 - SYSTEM FUNCTIONS AT A GLANCE; DASH LED INDICATORS

128-8483 23 of 24 Page 23 PRO9801N SYSTEM FUNCTIONS AT A GLANCE DASH LED INDICATORS RAPID FLASHING = PASSIVE ARMING/ACTIVE REARMINGSLOW FLASHING = ARMED OFF = DISARMED ON SOLID = VALET MODE 3 FLASH...PAUSE = INTRUSION ZONE 3 2 FLASH...PAUSE = INTRUSION ZONE 2 1 FLASH...PAUSE = INTRUSION ZONE 1 SIREN...