Audiovox PRO9801C - Manuals

Page 2 - YOUR “CODE HOPPING“ TRANSMITTERS

128-8794 2 of 24 Page 2  Protected Push Button LED Valet/Override Switch In Windshield Receiver  7-Function LED-Arm / Disarm / Zone 1 / Zone 2 / Zone 3 / Valet / Arming  Intrusion Alert With Memory  Instant Siren Activation When Used  Starter Disable Output  Additional Engine Immobilizer Outpu...

Page 3 - will not; ARMING THE SYSTEM - ACTIVE

128-8794 3 of 24 Page 3 known as a code grabber, which will receive and store the signal from your keychain transmitter and re-transmit at a later time to disarm your system.Your Keeloq Code Hopping transmitters will change their signal every time the button is pressed, so when a thief grabs then re...

Page 4 - PROTECTION WHILE THE SYSTEM IS ARMED

128-8794 4 of 24 Page 4  The dash mounted LED begins to flash slowly.  Parking Lights flash one time.  Siren will not sound. If the siren "chirped" three times, sometime after arming, the exclusive delayeddome light learn circuit has been programmed and the system detected a openentry poi...

Page 5 - SILENT DISARMING

128-8794 5 of 24 Page 5  Any mild impact to the vehicle’s glass will cause the alarm to sound a short series of warning tones.  Any strong impact to the vehicle’s glass will cause the alarm to trigger for the full 30 second alarm cycle. NOTE: If the optional interior illumination circuit was insta...

Page 6 - remain in the valet mode.

128-8794 6 of 24 Page 6  Parking Lights flash two times. If the parking lights flashed three times, then the alarm was triggered in yourabsence. Before turning the key on, examine the LED to identify which zone wastriggered.  Siren will not sound. If the siren sounds 4 chirps, then the alarm was t...

Page 7 - Programming Your Custom Override Code:; sequence. Turn the ignition switch to the on position.; Custom Code Programming Example:

128-8794 7 of 24 Page 7 3. To return to normal operation, press and release the Push-Button switch any time the ignition is on. NOTE: Always remember to return the vehicle to the valet off position. This will ensure thatthe vehicle remains protected at all times. MANUALLY OVERRIDING YOUR SYSTEM:Usin...

Page 8 - ELIMINATING THE NORMAL ARM/DISARM CHIRPS; button switch 3 times.

128-8794 8 of 24 Page 8 2. Turn the ignition switch to the on position.3. Within 10 seconds, press and release the Receivers Push-button switch, 3 times.4. Within 10 seconds turn the ignition switch off, on, off, on, off, on. (The siren or horn will beep and the lights will flash one time.) 5. Withi...

Page 10 - Push-Button LED Receiver Safety Control Switch; To Exit Remote Start Override Mode; REMOTE STARTING THE VEHICLE; occurs. DO NOT remote start the vehicle if it is garaged.; To Remote Start The Vehicle:

128-8794 10 of 24 Page 10 To change or adjust the shock sensor, press and release the ARM button of your keychain transmitter. 1. Within 2 seconds of arming, press and release the ARM button 1 time to defeat the pre-detect stage of the shock sensor. (The lights will flash and the siren will chirp on...

Page 13 - TURBO TIMER MODE

128-8794 13 of 24 Page 13 ADDITIONAL REMOTE FUNCTION (CHANNEL 6 ) Channel 6 is an alternate output that can be controlled by the unlock button of the transmitter, or by and independent button or combination of buttons. For your vehicle this output is: Controlled By:  Trunk/Key Button  Option Butto...

Page 14 - TRANSCEIVER ICONS AND THEIR INDICATIONS

128-8794 14 of 24 Page 14 2. Set the parking, (hand), brake.3. Be certain your foot is off the brake pedal.4. Press the receiver's program/Push-Button switch 2 times within 5 seconds.The parking lights will flash two times indicating the mode was successfullyentered.If your parking lights flashed fo...

Page 19 - Timing Count Down

128-8794 19 of 24 Page 19 Battery Indicator: Your transmitter has a battery indicator that is shown in the upper right corner of the screen as shown left. This icon indicates a new battery shown with 3 bars. As the battery deterio- rates, the bars will disappear. 1 bar indicates the battery should b...

Page 20 - Temperature Start Mode.; This icon will appear when the temp start

128-8794 20 of 24 Page 20 Temperature Start Mode. This icon will appear when the temp start mode is activated. The vehicle will start one time automatically when the temperature reaches 0*. Caution Be certain vehicle is outside before activating this mode. To toggle this feature on or off, from the ...

Page 22 - THIS PAGE LEFT BLANK INTENTIONALLY

128-8794 22 of 24 Page 22 THIS PAGE LEFT BLANK INTENTIONALLY

Page 23 - SYSTEM FUNCTIONS AT A GLANCE; DASH LED INDICATORS

128-8794 23 of 24 Page 23 PRO9801C SYSTEM FUNCTIONS AT A GLANCE DASH LED INDICATORS RAPID FLASHING = PASSIVE ARMING/ACTIVE REARMINGSLOW FLASHING = ARMED OFF = DISARMED ON SOLID = VALET MODE 3 FLASH...PAUSE = INTRUSION ZONE 3 2 FLASH...PAUSE = INTRUSION ZONE 2 1 FLASH...PAUSE = INTRUSION ZONE 1 SIREN...