Audiovox Drop Down Video TV/Monitor with DVD - Manuals

Page 2 - Important Notice; It is unlawful in most jurisdictions for a person

Important Notice It is unlawful in most jurisdictions for a person to drive a motor vehicle which is equipped with a television viewer or screen that islocated in the motor vehicle at any point forward of the back of the driver's seat, or that is visible directly or indirectly to the operator of the...

Page 3 - MATERIALS INCLUDED IN THIS PACKAGE:

MATERIALS INCLUDED IN THIS PACKAGE: 1) PROV716/PROV716 S/PROV716 P TV/Video Monitor with DVD (1pc)2) 12 Pin Power / Signal harness (P/N 112B2821) (1 pc)3) 3 Pin Power Wire Harness with choke (P/ N 112B3274) (1 pc)4) Hardware Package #4 x 3/8” Screws (9 pcs)#8 x 5/8” Self Drilling Screws (4 pcs)#8 Wa...

Page 4 - GENERAL INSTALLATION APPROACH:; their respective locations.; GENERAL SYSTEM CONFIGURATIONS:

GENERAL INSTALLATION APPROACH: 1) Decide upon system configuration and options that will be installed (i.e.: what components, VCP, Video Game, external amp, wireless headphones, VCP, etc.). 2) Review all manuals to become familiar with electrical requirements and hook ups.3) Decide upon mounting loc...

Page 6 - MINI CONSOLE INSTALLATION:; Lowest point mark

MINI CONSOLE INSTALLATION: This page only covers special installation considerations for the mini-console installation. If the videomonitor is to be installed in a vehicle with the mini console, this console may need to be trimmed to fit thecontour of the vehicle headliner. 1) In this installation, ...

Page 7 - MOUNTING THE MINI-CONSOLE; R oof

-5- MOUNTING THE MINI-CONSOLE R oof R oof S upport H eadliner 12”x9”x3/4” Plyw oodB lock (4) S elf-Tapping S crew s (not supplied) M ini-C onsole Video U nit (5) # 8 Flat W ashers (5) # 8x3/4” S elf-Tapping S crew s

Page 8 - Figure A; the main PCB and into the Mini-Din Connector on the main PCB.; Note; OPTIONAL

Figure A 1) Make the connections to the vehicle for the 12 pin wiring harness and battery wire.2) Insert the Circular Mini-Din Connector of the source component harness through the wire tie loop on the main PCB and into the Mini-Din Connector on the main PCB. 3) Pull the wire tie loop tight and cut ...

Page 9 - is external to the XM receiver.

PROV716/PROV716 S/PROV716 P INSTALLATION INSTRUCTIONS WHEN USINGSATELLITE RADIO The PROV716/PROV716 S/PROV716 P pods have dual IR transmitters. Channel A handles normalaudio program material from A/V sources (DVD/AUX/TV, etc). The second B channel allows anexternal audio source such as Satellite Rad...

Page 10 - Positive Switched Dome lighting; CONNECTING THE DOME LIGHTS; This is the switching wire.

Positive Switched Dome lighting -8- CONNECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle's wiring. There are two common types of dome light circuits used, positive or negative switched. Positive systems supply voltage to the interior lights to turn...

Page 11 - Negative Switched Dome lighting; connector; Factory Dome light circuit

Troubleshooting: SYMPTOM: No power at Video Monitor P o w e r b u t n o v i d e o o rsound Picture, but no sound S t a t i c o n T V S t a t i o n s(Tuner Version Only) No Infrared remote func-tions for VCP (or other com-ponents) REMEDY: -Verify +12 VDC on Red wire at 2 pin Power Harness behind vide...