Audiovox CCS-100 - Manuals - manualsarea.com

Page 2 - MANUAL PREPARED AND PROVIDED BY LITEON AUTOMOTIVE CORPORATION; INDEX; Page

MANUAL PREPARED AND PROVIDED BY LITEON AUTOMOTIVE CORPORATION INDEX 1. Cruise Control Installation: ..................................................... Parts List ...........................................................................Throttle Connections...........................................

Page 3 - HOW THE CRUISE WORKS; Required Tools

HOW THE CRUISE WORKS The Cruise Module makes "decisions" based upon speed,tachometer, and brake signal information. The controlcircuit interprets digital speed information from the car's engine control module (VSS) or Magnet Kit and ignitioncoil output. Brake information comes from the red a...

Page 4 - PARTS LIST

CRUISE CONTROL M6 x 5/8" long hex head bolt ( 3 ) Servo Assembly ( 1 ) Tie Straps ( 10 ) 1/2" rubber bulkhead grommet ( 1 ) - 1 - - 4 - - 5 - Convoluted tubing ( 1 ) Vacuum hose reducing nipple ( 1 ) Assorted Vacuum T - Connectors Vacuum Hose - Short ( 1 ) Vacuum Hose - Long ( 1 ) - 6 - - 7 ...

Page 8 - Plug the vacuum hose onto the servo assembly.; See Diagrams below for common vacuum source connection.

CAUTION ! ATTACH THE CRUISE CONTROL CABLE SO THAT IT PARALLELS THE EXISTING THROTTLE CABLE AS NEARLY AS POSSIBLE. WARNING ! AFTER ATTACHING THE CRUISE CONTROL CABLE TO THE VEHICLE’S THROTTLE, OPERATE THE THROTTLE MANUALLY ( FULL TRAVEL ) FROM BOTH UNDER HOOD AND ACCELERATOR PEDAL TO BEABSOLUTELY SUR...

Page 9 - Routing the Main Wiring Harness; to the magnet speed sensor.

Routing the Main Wiring Harness 1. Locate your vehicle by make, model, and engine size in the included Reference Manual in order to identify the location of the VSS and Tach connection locations. If your make and model cannot be located, then the MagnetKit must be installed. Follow the installation ...

Page 11 - RED; GREEN; DASH

Figure 1 Drill 1/4" Dia. holes, (2 places). Carefully cut-out along dottedlines and place on selected area. DASH BOARD TEMPLATE Use a file or razor knife to remove the material between the 2 holes. Figure 3 CONTROL SWITCH CONNECTIONS CRUISE CONTR OL Figure 2 RED CONNECTOR 1 2 3 4 GREEN BR OW N Y...

Page 12 - ROAD TESTING THE CRUISE CONTROL

ROAD TESTING THE CRUISE CONTROL Be sure to fully test all functions of your new cruise control on a level surface away from predestrian and vehicletraffic. While travelling 35 M.P.H. turn switch on , then press Set button. Unit will engage when Set button isreleased. To disengage, tap on brake or tu...

Page 13 - TROUBLE SHOOTING

TROUBLE SHOOTING WIRING - 10 PIN CONNECTOR Note : If the brown, green, or yellow wires do not test properly, proceed immediately to the testing of the 4 pin control switch testing. POS WIRE COLOR FUNCTION 9 Black Always continuity to ground 3 Red Always + 12 VDC 1 Brown + 12 VDC with Ignition switch...

Page 14 - MAGNET AND SPEED SENSOR COIL INSTALLATION

M M M M M A A A A AGNET KIT GNET KIT GNET KIT GNET KIT GNET KIT INST INST INST INST INSTALLA ALLA ALLA ALLA ALLAT I T I T I T I T IO O O O O N N N N N MAGNET AND SPEED SENSOR COIL INSTALLATION The magnets, along with the speed sensor coil provide pulses to calculate road speed for the cruise control...

Page 15 - SPEED SENSOR COIL INSTALLATION; NOTE: This magnet kit cannot be used on Honda vehicles.

Step 6: While rotating the shaft, carefully snap one wire into one set of magnet slots. Loosely wrap the wireto hold it in place. Snap the second wire into the remaining slots making sure the ends are nearly oppositethe first wire, as shown in Figure 4 or 11. Step 7: Carefully pull wires tight, and ...

Page 17 - INSTALLATION - FRONT WHEEL DRIVE VEHICLES; Figure 6

INSTALLATION - FRONT WHEEL DRIVE VEHICLES TRANSMISSIONAXLE HOUSING 3/8" DRILL OR FILE BRACKET TO FITEXISTING BOLT WIRES AND MAGNET DIA. OFMOUNTING SURFACE RIGHT FRONTAXLE ONLY 1/2" 3/8" Figure 6 Figure 7 Figure 11 Figure 8 Figure 9 MAGNET MAGNET Figure 10 -15-

Page 18 - 2 MONTH LIMITED WARRANTY; Applies to automotive speed controls.

-16- AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that shouldthis product or any part thereof, under normal use and conditions, be proven defective in material orworkmanship within 12 months from the date of original purchase, such defect(s) will be re...