Audiovox BTR120 - Manuals - manualsarea.com

Page 2 - INDEX

Specifications........................................................................... 1Precautions.............................................................................. 2Installation Instructions............................................................ 3Wiring Instructions...............

Page 3 - Saturday; SPECIFICATIONS

Input Sensitivity: Low-level 200 mV. - 2 V.High-level 2V - 10 V. Supply Voltage: 12 volts, negative ground Fuse Rating: 5 amps. Dimensions (W X H X D): 8-5/8" X 2-1/8" X 3-15/16”219 mm X 54.3 mm X 100 mm Maximum Output Power: 120 Watts 30 watts RMS @ 4 Ohms Output Impedance: 4-8 Ohms Frequen...

Page 4 - must; PRECAUTIONS

1. Although this unit is designed with built-in self-protection circuits, there may be a possibility of damage if it is not wired correctly. Please follow the wiring instructions carefully for the type of system being used. 2. The last lead to be connected is the wire to the positive( ) terminal of ...

Page 5 - CHECK BEFORE YOU DRILL!; Secure the amplifier to the mounting surface using; INSTALLATION INSTRUCTIONS; MOUNTING SURFACE; INSTALLATION DIAGRAM

-3- 1. Select a mounting area where the amplifier will have sufficient air circulation for proper cooling.Inadequate air circulation will cause the temperatureof the amplifier to rise and will trigger the thermalprotection mode. 2. Place the amplifier on the mounting surface and mark the locations o...

Page 6 - WIRING INSTRUCTIONS

T h e w i r i n g o f y o u r a m p l i f i e r w i l l d e p e n d o n t h e s y s t e m a n d s p e a k e r s y o u a r e u s i n g b u t w i l l e i t h e r b e a 4 - C h a n n e l ,3-channel, 2-channel, or mixed-mono application. The following pages illustrate the input and output wiring for the...

Page 7 - Speaker Connections; ground any speaker leads to the chassis of the vehicle.; DO NOT; use both input levels at the same time.

4. Speaker Connections Depending on the type and number of speakers used with the amplifier, wire them to the speaker terminals as per the appropriate wiring diagram. For most applications, #18 gauge wire should be used for the speaker leads but in no case thinner than #20 gauge. For leads in excess...

Page 8 - INPUT WIRING DIAGRAM; CAR STEREO

-6- INPUT WIRING DIAGRAM IMPORTANT USE EITHER HIGH-LEVEL OR LOW-LEVEL INPUT, NOT BOTH. CAR STEREO HIGH-LEVEL (SPEAKER) INPUT(WIRE SIDE VIEW) LOW-LEVEL INPUT RCA TYPE SHIELDED EXTENSION CABLES (NOT INCLUDED) 1 2 Gray Brown Black Green White HI-INPUT HI-INPUT GND GND L + L + R + R + LL RR MIN MIN MAX ...

Page 9 - BATTERY; OUTPUT WIRING DIAGRAM; NEVER COMBINE (BRIDGE ) OUTPUTS FOR USE WITH

-7- LEFT SPEAKER CAR STEREO GROUND FUSE FUSE REM BATT GND LEFT RIGHT BATTERY FOR 12 VOLT USE ONLY AUTO-ANTENNA LEAD USE # 16 GAUGE WIRE RIGHT SPEAKER 3 GROUND METALSECTION OF VEHICLE EXISTING SCREW OR BOLT CLEAN PAINT, RUST, DIRTOR GREASE FROM AREA FOR GOOD CONNECTION. OUTPUT WIRING DIAGRAM WARNING!...

Page 10 - OPERATION

-8- Power Indicator Lamps The Power Indicator Lamps will light to indicate that the unit is connected to the battery and that the RemoteTurn-On terminal is receiving +12 volts, thus turningon the amplifier. After initial set-up, the amplifier should not require any further adjustment unless there is...

Page 11 - CANADA; 0 DAY/12MONTH LIMITED WARRANTY

AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof,under normal use and conditions, be proven defective in material or workmanship within 90 days from the date of original purchase, suchdefect(s) will be repaired ...

Page 12 - Printed in Korea

2003 Audiovox Electronics Corporation, Hauppauge, N.Y. C C 128-6564 Printed in Korea