Audiovox AXT-500 - Manuals - manualsarea.com

Page 2 - INDEX

Specifications.....................................................................3Precautions........................................................................ 4Installation Instructions...................................................... 5Wiring Instructions..................................

Page 3 - HIGH PERFORMANCE STEREO AMPLIFIER; Saturday

Input Impedance: Low-Level 10K OhmsHigh-Level 100 Ohms Input Sensitivity: Low-Level 200 mV - 8 V.High-Level 2V - 10 V Filter type: Selectable Full/Low-pass Crossover @ 12dB/Octave Filter Crossover: LPF 50-250 Hz (variable) Supply Voltage: 12 volts, negative ground Fuse Rating: 30 amps. Dimensions (W...

Page 4 - must; PRECAUTIONS

1. Although this unit is designed with built-in self-protection circuits, there may be a possibility of damage if it is not wired correctly. Please follow the wiring instructions carefully for the type of system being used. 2. The last lead to be connected is the wire to the positive( ) terminal of ...

Page 5 - CHECK BEFORE YOU DRILL!; Secure the amplifier to the mounting surface using; INSTALLATION INSTRUCTIONS

1. Select a mounting area where the amplifier will have sufficient air circulation for proper cooling.Inadequate air circulation will cause the temperatureof the amplifier to rise and will trigger the thermalprotection mode. 2. Place the amplifier on the mounting surface and mark the locations of th...

Page 6 - WIRING INSTRUCTIONS

The wiring of your amplifier will depend on the system and speakers you are using but will either be a stereo, mono, ormixed-mono application. The following pages illustrate the input and output wiring for these types. please refer to theappropriate diagrams for the system configuration you are usin...

Page 7 - Speaker Connections; ground any speaker leads to the chassis of the vehicle.; DO NOT; use both input levels at the same time.

4. Speaker Connections Depending on the type and number of speakers used with the amplifier, wire them to the speaker terminals as per the appropriate wiring diagram. For most applications, #16 gauge wire should be used for the speaker leads but in no case thinner than #18 gauge. For leads in excess...

Page 8 - CAR STEREO; -CHANNEL AND MIXED-MONO INPUT WIRING DIAGRAM

-8- CAR STEREO Right Rear+ HIGH-LEVEL (SPEAKER) OUTPUTS USE EITHER HIGH-LEVEL OR LOW-LEVEL INPUT, NOT BOTH. IMPORTANT GND GND 2CH 2CH 1CH 1CH 3CH 3CH 4CH 4CH X-OVER X-OVER 50Hz 50Hz 250Hz 250Hz 250Hz 250Hz MIN MIN MAX MAX LPF LPF 50Hz 50Hz LPF LPF GAIN GAIN MIN MIN MAX MAX GAIN GAIN LPF LPF FULL FUL...

Page 9 - BATTERY; -CHANNEL AND MIXED-MONO OUTPUT WIRING DIAGRAM

-9- CAR STEREO GROUND BATTERY FOR 12 VOLT USE ONLY AUTO-ANTENNA LEAD GROUND METALSECTION OF VEHICLE EXISTING SCREW OR BOLT CLEAN PAINT, RUST, DIRTOR GREASE FROM AREA FOR GOOD CONNECTION. LEFT FRONT SPEAKER REM BATT GND BRIDGED BRIDGED BRIDGED BRIDGED CH1 CH2 CH3 CH4 FUSE FUSE LEFT REAR SPEAKER RIGHT...

Page 10 - -CHANNEL INPUT WIRING DIAGRAM; WIRE SIDE VIEW

-10- CAR STEREO Right Rear+ HIGH-LEVEL (SPEAKER) OUTPUTS USE EITHER HIGH-LEVEL OR LOW-LEVEL INPUT, NOT BOTH. IMPORTANT GND GND 2CH 2CH 1CH 1CH 3CH 3CH 4CH 4CH X-OVER X-OVER 50Hz 50Hz 250Hz 250Hz 250Hz 250Hz MIN MIN MAX MAX LPF LPF 50Hz 50Hz LPF LPF GAIN GAIN MIN MIN MAX MAX GAIN GAIN LPF LPF FULL FU...

Page 11 - -CHANNEL OUTPUT WIRING DIAGRAM

-11- CAR STEREO GROUND BATTERY FOR 12 VOLT USE ONLY AUTO-ANTENNA LEAD GROUND METALSECTION OF VEHICLE EXISTING SCREW OR BOLT CLEAN PAINT, RUST, DIRTOR GREASE FROM AREA FOR GOOD CONNECTION. LEFT FRONT SPEAKER REM BATT GND BRIDGED BRIDGED BRIDGED BRIDGED CH1 CH2 CH3 CH4 FUSE FUSE LEFT FRONT SPEAKER RIG...

Page 14 - Power Indicator Lamps; OPERATION; Protection Mode LED

-14- Power Indicator Lamps After initial set-up, the amplifier should not require any further adjustment unless there is a change in the carstereo or speaker system with which it is used. If activated by a rise in emperature, the unit will resume operation after cooling off to a normal operating ran...

Page 15 - below; High Level Input Connection

LPF Crossover Frequency Control T h i s C o n t r o l s e l e c t s t h e c r o s s o v e r f r e q u e n c y w h e n t h eSub woofer Crossover Selector is in the "LPF" setting.Adjust it to the appropriate position for the characteristicsa n d c r o s s o v e r f r e q u e n c y r e q u i r ...

Page 16 - CANADA; 0 DAY/12MONTH LIMITED WARRANTY

AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof,under normal use and conditions, be proven defective in material or workmanship within 90 days from the date of original purchase, suchdefect(s) will be repaired ...

Page 17 - Printed in Korea

2003 Audiovox Electronics Corporation, Hauppauge, N.Y. C C Printed in Korea 128-6561 1