Audiovox APS-995 - Manuals - manualsarea.com

Page 2 - INSTALLATION OF THE MAJOR COMPONENTS:

Eighth Press and release the valet switch 1 chirp = siren and horn output Press transmitter Lock button to change 2 chirps = siren output only Press transmitter lock button to change 3 chirps = horn output only o r Ninth Press and release the valet switch 2 chirps = horn chirp output 16mS Press tran...

Page 5 - SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS.; YELLOW START WIRE DETAIL

YELLOW Wire: Starter OutputCareful consideration for the connection of this wire must be made to prevent the vehicle fromstarting while in gear. Understanding the difference between a mechanical and an electricalNeutral Start Switch will allow you to properly identify the circuit and select the corr...

Page 7 - Siren Wiring Detail; SIREN; Positive Door Switch Wiring Detail

White w/ Black Trace Wire: (+) Siren OutputThis is the positive siren feed wire. Route this wire through a grommet in the firewall to the sirenlocation. Connect the White w/ Black Trace wire to the Red wire of the siren. Secure the Black wire ofthe siren to a known chassis ground or solid clean meta...

Page 8 - General Motors VATS By-Pass Diagram

Light Blue Wire: Ignition 3 OutputThis wire provides a 300mA ground output that becomes active 3 seconds before the Remote Start Unitinitializes and remains grounded while running plus an additional 4 seconds after the Remote Start Unitturns off. In all of the applications described below, a relay w...

Page 12 - Channel 3 Relay Wiring Detail

Dark Blue Wire: Delayed 300mA Pulsed Channel 3 OutputThe Dark Blue wire supplies a 300mA ground pulsed output whenever channel three of the receiver isaccessed. Pressing the pre-programmed transmitter button for three seconds will access channel two.This is a low current output and must be connected...

Page 13 - some remote start trigger inputs, will damage the control module.

1 3 should be connected ). Cut the low current starter solenoid wire in the vehicle and connect one side of thecut wire to relay terminal 87. Connect the other side of the cut wire to relay terminal 30.Note : This is a normally opened starter cut arrangement and when power is removed from the securi...

Page 17 - ALARM SELECTABLE FEATURES

1 7 NOTE: Resistive Circuits, As Well As 4 Wire Polarity Reversal and 5 Wire Alternating 12 Volt Door Lock Control CircuitsThese applications require the use of additional components which may include relays, fixed resistors, orfor convenience, the AS 9159 Door Lock Interface. Refer to the AUDIOVOX ...

Page 18 - REMOTE START SELECTABLE FEATURES; verifying you are in the feature program mode.

1 8 TIMED START PROGRAM:The Remote Start unit has the ability to start the vehicle automatically at timed intervals. This feature isuseful in extremely cold climates where starting the engine is the only means to keep the battery chargedand fluids warm. The operator has the option to have the unit s...

Page 19 - NOTE: All applications require that tach be programmed.

NOTE: Once you've entered the program mode DO NOT allow more than 15 seconds to pass between steps,or the programming mode will be terminated.Programming Tach Rate: NOTE: All applications require that tach be programmed. The unit will not operate unless tach is programmed. If an attempt is made to s...

Page 22 - OF THE NEUTRAL SAFETY START FEATURE.; two circuits may be used only if the above circuit is not available.; METHOD 1

CAUTION! REMEMBER TO RECONNECT THE BROWN/BLACK WIRE TEMPORARILY DISCONNECTED IN STEP 3 DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE OPERATION OF THE NEUTRAL SAFETY START FEATURE. KEY IN SENSOR CIRCUITS:If the vehicle you are working on does not have or you cannot locate the ECM ...

Page 23 - Make sure to clean the surface before affixing the label.

2 3 METHOD 2 To connect to the key in sensor circuit as shown for method 2:A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch.B. Cut this wire and connect the ignition cylinder side to chassis ground.C. Locate the key in sensor switch wire that connects ...