Audiovox APS-55TWT - Manuals

Page 2 - INSTALLATION OF THE MAJOR COMPONENTS:; PROGRAM SWITCH; AUTOMATIC TRANSMISSIONS; only! Although this combination Keyless; IT MUST NOT; be installed into a

128-7199 2 of 16 This Remote Start/Keyless Entry System is designed for use with Automatic Transmission Vehicles Only! Theunit provides wait to start input for glow plug pre-heat which will be used for all diesel applications. If this wire isnot connected, then the unit will remain in the Gasoline m...

Page 4 - SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS.; Ignition 1 Output

128-7199 4 of 16 Failure to connect this wire to the ignition switch side of the neutral safety switch can result in personal injury andproperty damage. SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS. BLUE WIRE: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch. ...

Page 5 - WIRING CONNECTIONS: 12 Pin Input / Output Harness; Chassis Ground Source; Control Switch; Negative Inhibit Input 1

128-7199 5 of 16 WIRING CONNECTIONS: 12 Pin Input / Output Harness Black Wire: Chassis Ground Source Connect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis. Be certain toremove any paint or grease and secure this wire with a self-tapping screw and ring ...

Page 6 - Brake Switch Positive Shutdown Detail; Ignition 3 / Shock Disable Output

128-7199 6 of 16 Brake Switch Positive Shutdown Detail YELLOW w/ BLACK Tracer Wire: + 12 Volt Alarm By - Pass Output NOTE: You must disconnect the ignition input of the alarm from any other wire that it is presently connected to in the vehicle.This wire provides a + 12 Volt output when the ignition ...

Page 7 - General Motors VATS By-Pass Diagram

128-7199 7 of 16 7 A. Shock Sensor By Pass: If there is Shock Sensor used with an alarm system and it is not shunted during the Remote Start activationperiod, then vibration from the running vehicle can cause the alarm to trigger. In this case, connect the Light BlueWire to terminal #86 of a externa...

Page 8 - Tach Sensor Input; Tachometer Input Wiring Detail; Diesel Wait To Start Input; WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS; Pulsed Ground Output Before Start

128-7199 8 of 16 Green/Orange Wire: Tach Sensor Input This wire will continually monitor the engine tach rate while the unit is under power of the Remote Start module. Thiswire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and connect tothe negative...

Page 9 - Wire Ground Switched Door Lock Circuits:; Wire Ground Switched Door Lock/Unlock Wiring Detail; Wire Positive Switched Door Locks:; Wire Positive Switched Door Lock/Unlock Wiring Detail

128-7199 9 of 16 NOTE: The outputs above are low current outputs and must be used with a relay if the circuit's requirement is more than 300 mA. 2 Pin Door Lock/Unlock Harness: (White Connector) The Red & Green Door Lock/Unlock output wires provide either a pulsed ground or pulsed + 12 volts to ...

Page 10 - Pin Blue Connector :; Push-Button Programming Switch; Pin White Auxiliary Output Connector :; Low Current Trunk Release Output; To program these selectable features:; EXAMPLE

128-7199 10 of 16 10 Resistive Circuits, As Well As 4 Wire Polarity Reversal and 5 Wire Alternating 12 VoltDoor Lock Control Circuits These applications require the use of additional components which may include relays, fixed resistors, or forconvenience, the AS 9159 Door Lock Interface. Refer to th...

Page 11 - Multi Coil Pack Adapter:

128-7199 11 of 16 11 first programming tach, the unit will flash the parking lights 7 times indicating tach has not been learned and stored.If the tach rate is not properly programmed to the specific vehicle, the unit may not realize that the vehicle is runningin certain instances and could re-engag...

Page 12 - switch off. DO NOT attempt to remove the key.

128-7199 12 of 16 HOOD PIN SAFETY SHUT DOWN: The intention of the hood pin safety shut down is to prevent the Remote Start unit from being activated while amechanic or vehicle owner is performing normal routine vehicle maintenance.To test the integrity of this circuit:1. With the driver's window in ...

Page 13 - KEY IN SENSOR CIRCUITS:; Method 1

128-7199 13 of 16 W A R N I N G ! ! REMEMBER TO RECONNECT THE BROWN/BLACK WIRE TEMPORARILY DISCONNECTED IN STEP 3. DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE OPERATION OF THE NEUTRAL SAFETY START FEATURE. MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERATIONS: Mechanical neutral safe...

Page 14 - Method 2; METHOD 1; METHOD 2

128-7199 14 of 16 14 Method 2 will allow the safety required for the remote start unit and prevent the vehicle from starting while in any gear other than Park or Neutral while the key is in the ignition cylinder. However, the original factory key in chime modulewill not alert the owner that the key ...

Page 15 - COMPLETING THE INSTALLATION:; under the dash board or in the engine compartment areas.; point these out to the customer.

128-7199 15 of 16 NOTE: A second 4002 series diode may be required to maintain the integrity of the hood open, shut down circuit. Ifthis is the case, it must be installed as shown in the diagram above. The anode (Non Striped) side must beconnected to the Gray/Black wire of the Remote Start Unit. The...