Audiovox APS-55LRa - Manuals

Page 2 - INSTALLATION OF THE MAJOR COMPONENTS:; PROGRAM SWITCH

128-6504A 2 of 16 The APS-55 Remote Start/Keyless Entry System is designed for use with Automatic Transmission Vehicles Only!The unit provides wait to start input for glow plug pre-heat which will be used for all diesel applications. If this wireis not connected, then the unit will remain in the Gas...

Page 3 - Starter Output

128-6504A 3 of 16 3 THE RECEIVER/ANTENNA ASSEMBLY: The Superheterodyne Receiver Antenna Assembly provided with this unit allows routing from below the dashboardfor maximum operating range. Choose a location above the belt line (dashboard) of the vehicle for best reception.Special considerations must...

Page 5 - Accessory Output; WIRING CONNECTIONS: 12 Pin Input / Output Harness; Black Wire: Chassis Ground Source; Control Switch; GRAY WIRE: Negative Inhibit Input 1

128-6504A 5 of 16 VIOLET WIRE: Accessory Output Connect this wire to the Accessory wire from the ignition switch. This wire will show + 12 volts when the ignitionswitch is turned to the "ACCESSORY" or "ON" and "RUN" positions and will show 0 volts when the key is turned to th...

Page 6 - BROWN w/ BLACK Tracer Wire: Positive Inhibit Input 2; Brake Switch Positive Shutdown Detail; Switch

128-6504A 6 of 16 BROWN w/ BLACK Tracer Wire: Positive Inhibit Input 2 Any time + 12 Volts is applied to the Brown w/ Black tracer wire, the Remote Starter will stop operating, even if the signalis received from the transmitter. If the brake light switch in the vehicle switches + 12 Volts to the bra...

Page 7 - LIGHT BLUE Wire: Ignition 3 / Shock Disable Output; General Motors VATS By-Pass Diagram

128-6504A 7 of 16 LIGHT BLUE Wire: Ignition 3 / Shock Disable Output This wire provides a 300mA ground output that becomes active 3 seconds before the Remote Start Unit initializes,and remains grounded while running plus an additional 4 seconds after the Remote Start Unit turns off. In all of theapp...

Page 8 - Tachometer Input Wiring Detail; Green/Yellow Wire: Diesel Wait To Start Input

128-6504A 8 of 16 Green/Orange Wire: Tach Sensor Input This wire will continually monitor the engine tach rate while the unit is under power of the Remote Start module. Thiswire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and connect tothe negativ...

Page 9 - Wire Ground Switched Door Lock Circuits:; Wire Ground Switched Door Lock/Unlock Wiring Detail; Wire Positive Switched Door Locks:; Wire Positive Switched Door Lock/Unlock Wiring Detail

128-6504A 9 of 16 NOTE: The outputs above are low current outputs and must be used with a relay if the circuit's requirement ismore than 300 mA.2 Pin Door Lock/Unlock Harness: (White Connector) The Red & Green Door Lock/Unlock output wires provide either a pulsed ground or pulsed + 12 volts to c...

Page 10 - Pin Blue Connector : Programming Switch; To program these selectable features:

128-6504A 10 of 16 10 Resistive Circuits, As Well As 4 Wire Polarity Reversal and 5 Wire Alternating 12 VoltDoor Lock Control Circuits These applications require the use of additional components which may include relays, fixed resistors, or forconvenience, the AS 9159 Door Lock Interface. Refer to t...

Page 11 - HOOD PIN SAFETY SHUT DOWN:

128-6504A 11 of 16 11 4. Hold the program switch ON, then start the vehicle using the ignition key.5. When the unit senses the tach signal, the parking lights will begin to flash.6. Release the program switch. The parking lights will turn on for 3 seconds to indicate that the tach signal is stored a...

Page 13 - KEY IN SENSOR CIRCUITS:

128-6504A 13 of 16 MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERATIONS:Mechanical neutral safety switch configurations differ slightly in that they do not offer the same level of safety when installing aremote start device. Often when the ignition switch is turned off while the gear selector is in any p...

Page 14 - METHOD 2; METHOD 1

128-6504A 14 of 16 NOTE: A second 4002 series diode may be required to maintain the integrity of the hood open, shut down circuit. Ifthis is the case, it must be installed as shown in the diagram above. The anode (Non Striped) side must beconnected to the Gray/Black wire of the Remote Start Unit. Th...

Page 15 - COMPLETING THE INSTALLATION:; point these out to the customer.

128-6504A 15 of 16 NOTE: A second 4002 series diode may be required to maintain the integrity of the hood open, shut down circuit. If this is the case, it must be installed as shown in the diagram above. The anode (Non Striped) side must beconnected to the Gray/Black wire of the Remote Start Unit. T...