Audiovox ACC-52 - Manuals

PROCEDURE FOR HORIZONTAL INSTALLATION INSTALLATION The unit can be installed horizontally, vertically or at a 45° angle. The position of the built-in anti-vibration springs (left and rightside), must correspond to the mounting position chosen. If the springs are not set correctly for the type of ins...

Hexagonal boltwith washer base (M5 x 10) Bracket (R) Bracket (L) 4 2 Attach bracket (L) and bracket (R) to each side of theunit, using the hexagonal bolts with washer base(M5 x 10). Mount the unit in place, using four self-tapping screws(M5 x 12).Use RTV (silicone sealer) on screw threads or aroundt...

4 2 Attach bracket (L) and bracket (R) to each side of theunit, using the hexagonal bolts with washer base(M5 x 10). Mount the unit in place, using four self-tapping screws(M5 x 12).Use RTV (silicone sealer) on screw threads or aroundthe holes to prevent moisture intrusion. Set the left and right an...

9 NOTE: When routing wires and cablesfrom the rear of the car to the dash-board, it is best to conceal the wiresunder carpeting. If you do not knowhow to do this, your local auto me-chanic or car stereo installer should beconsulted. REMOTE CONTROLCABLE (4-1/2 FEET) CHANGER BLACK GROUND WIRE OVERALL ...

10 WIRING THE FM MODULE The FM module should be positioned near your existing car stereo and the 15 foot data cable should be connected to it. Make the following connections to the FM module: 15 FOOT DATA CABLE "TO CD CHANGER"LABEL CAR FUSEBLOCK ORANGE w/WHITESTRIPE WIRE 15 FOOT EXTENSION LE...

CONTROLS LCD Display Play/Pause ( / II) Power Off Switch (OFF) Disc Select ( + - ) Track Select ( ) Track Search ( ) Track/Disc Shuffle (SHFL) Track/Disc Repeat (RPT) Track/Disc Scan (SCN) Reset Button PREPARING FOR OPERATION 1. Load CD magazine bm and insert into changer as described on page 16. 2....

USE OF CONTROLS pressing the Shuffle again, or by activating the Scan 9 orRepeat 8 functions.When the Shuffle button is pressed and held longer than 2seconds, the SHFL and DISC indications will appear on theLCD panel and the discs in the magazine will be played in arandom shuffled order, as well as ...

This CD Changer is designed to be operated only on 12 volt DC negative ground systems. The unit can not be used on 24 voltor positive ground systems. TEMPERATUREThe unit may not operate correctly in extremely hot or cold temperatures. It is equipped with a built-in thermal protection circuitwhich wi...

LOADING DISCS INTO THE MAGAZINEThis CD Changer uses a specially-designed magazine to holdup to 10 compact discs. To load discs into the magazine, gripthe tab on the magazine tray into which you will be loading adisc and pull it out gently as shown in Figure 1. Pull out only onetray at a time. Insert...

CD CHANGER OPERATING INSTRUCTIONS This CD Changer is designed to operate through a compatible Audiovox car stereo which incorporates thecontrols and display functions or through the FM section of any car stereo. Please check with your Audiovoxstereo specialist for recommendations of the models that ...

TROUBLESHOOTING An error made in operation or during installation of this product may be mistaken for a system malfunction. Please performthe checks described below before contacting your dealer or service facility. No power Magazine cannot beinstalled CD is not played Noise, skipping, orintermitten...

AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this productthat should this product or any part thereof, under normal use and conditions, be proven defectivein material or workmanship within 12 months from the date of original purchase, such defect(s) willbe repaired...