Audiovox 128-8210 - Manuals

Page 2 - MUST HAVE a Tach Signal; INSTALLATION OF THE MAJOR COMPONENTS:; PROGRAM SWITCH; AUTOMATIC TRANSMISSIONS; only! Although this combination Keyless; IT MUST NOT; be installed into a

128-8210 2 of 16 2 This Remote Start System is designed for use with Automatic Transmission Vehicles Only! The unit provides waitto start input for glow plug pre-heat which will be used for all diesel applications. If this wire is not connected, thenthe unit will remain in the Gasoline mode setting,...

Page 3 - Do not remove the fuse holders from this wire harness. Fuses must be; + 12 volt Battery 1 Source

128-8210 3 of 16 3 THE RECEIVER/ANTENNA ASSEMBLY: The Superheterodyne Receiver Antenna Assembly provided with this unit allows routing from below the dashboardfor maximum operating range. Choose a location above the belt line (dashboard) of the vehicle for best reception.Special considerations must ...

Page 4 - SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS.; Ignition 1 Output

128-8210 4 of 16 4 NOTE: This wire must be connected to the vehicle side of the starter cut relay (when used). For the electrical neutralswitch configuration, this connection must be made between the starter inhibit relay, (when used) and theneutral safety switch as shown in the following diagram. F...

Page 5 - Accessory Output; WIRING CONNECTIONS: 12 Pin Input / Output Harness; Chassis Ground Source; Control Switch; Negative Inhibit Input 1

128-8210 5 of 16 5 NOTE: See programming information concerning this wire to allow output during the "START" mode. VIOLET WIRE: Accessory Output Connect this wire to the Accessory wire from the ignition switch. This wire will show + 12 volts when the ignitionswitch is turned to the "ACCE...

Page 6 - Positive Inhibit Input 2; Brake Switch Positive Shutdown Detail; Switch

128-8210 6 of 16 6 BROWN w/ BLACK Tracer Wire: Positive Inhibit Input 2 Any time + 12 Volts is applied to the Brown w/ Black tracer wire, the Remote Starter will stop operating, even if the signalis received from the transmitter. If the brake light switch in the vehicle switches + 12 Volts to the br...

Page 7 - Ignition 3 / Shock Disable Output; from the resistor pack supplied.; General Motors VATS By-Pass Diagram

128-8210 7 of 16 7 LIGHT BLUE Wire: Ignition 3 / Shock Disable Output This wire provides a 300mA ground output that becomes active 3 seconds before the Remote Start Unit initializes,and remains grounded while running plus an additional 4 seconds after the Remote Start Unit turns off. In all of theap...

Page 8 - Tach Sensor Input; Tachometer Input Wiring Detail; Diesel Wait To Start Input; WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS; Pulsed Ground Output Before Start

128-8210 8 of 16 8 DARK GREEN Wire: Tach Sensor Input This wire will continually monitor the engine tach rate while the unit is under power of the Remote Start module. Thiswire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and connect tothe negative...

Page 9 - Pin Blue Connector :; EXAMPLE

128-8210 9 of 16 9 NOTE: The outputs above are low current outputs and must be used with a relay if the circuit's requirement ismore than 300 mA. 2 Pin Blue Connector : Push-Button Programming Switch Route the gray and black wires in the 2 pin connector from the previously installed push-button prog...

Page 11 - switch off. DO NOT attempt to remove the key.

128-8210 11 of 16 11 To test the integrity of this circuit:1. With the driver's window in the down position, start the vehicle using the RF transmitter.2. Reach inside the car and pull the hood release.3. Raise the hood and confirm that the remote start unit shuts down.If the unit fails this test, r...

Page 12 - KEY IN SENSOR CIRCUITS:; Method 1

128-8210 12 of 16 12 MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERATIONS: Mechanical neutral safety switch configurations differ slightly in that they do not offer the same level of safety when installing aremote start device. Often when the ignition switch is turned off while the gear selector is in an...

Page 13 - METHOD 1; METHOD 2

128-8210 13 of 16 13 These situations should be carefully considered before altering the vehicle's wiring and must be fully explained to theconsumer.Circuits may be used only if the above circuit is not available. METHOD 1 To connect to the key in sensor as shown in method 1:A. Locate the control wi...

Page 14 - COMPLETING THE INSTALLATION:; under the dash board or in the engine compartment areas.

128-8210 14 of 16 14 NOTE: A second 4002 series diode may be required to maintain the integrity of the hood open, shut down circuit. Ifthis is the case, it must be installed as shown in the diagram above. The anode (Non Striped) side must beconnected to the Gray/Black wire of the Remote Start Unit. ...