Audiovox 128-8111 - Manuals

Page 2 - To program these selectable features

128-8111 2 of 20 To program these selectable features; Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off Then On Short chirp, then long chirp This Action Accesses Feature Bank 2 Alarm Selectable Fe...

Page 5 - INSTALLATION OF THE MAJOR COMPONENTS:; PUSH-BUTTON LED SWITCH; The Remote Start System is to be used in vehicles with; AUTOMATIC TRANSMISSIONS

128-8111 5 of 20 This Remote Start/Keyless Entry System is designed for use with Automatic Transmission Vehicles Only! Theunit provides wait to start input for glow plug pre-heat which will be used for all diesel applications. If this wire isnot connected, then the unit will remain in the Gasoline m...

Page 6 - Starter Output

128-8111 6 of 20 6 THE RECEIVER/ANTENNA ASSEMBLY: The Superheterodyne Receiver Antenna Assembly provided with this unit allows routing from below the dashboardfor maximum operating range. Choose a location above the belt line (dashboard) of the vehicle for best reception.Special considerations must ...

Page 7 - SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS.; Ignition 1 Output

128-8111 7 of 20 NOTE: This wire must be connected to the vehicle side of the starter cut relay (when used). For the electrical neutralswitch configuration, this connection must be made between the starter inhibit relay, (when used) and theneutral safety switch as shown in the following diagram. Fai...

Page 8 - Accessory Output; WIRING CONNECTIONS: 12 Pin Input / Output Harness; Chassis Ground Source

128-8111 8 of 20 VIOLET WIRE: Accessory Output Connect this wire to the Accessory wire from the ignition switch. This wire will show + 12 volts when the ignitionswitch is turned to the "ACCESSORY" or "ON" and "RUN" positions and will show 0 volts when the key is turned to the...

Page 9 - Brake Switch Positive Shutdown Detail; Ignition 3 / Shock Disable Output

128-8111 9 of 20 Brake Switch Positive Shutdown Detail YELLOW w/ BLACK Tracer Wire: + 12 Volt Alarm By - Pass Output NOTE: You must disconnect the ignition input of the alarm from any other wire that it is presently connected to in the vehicle.This wire provides a + 12 Volt output when the ignition ...

Page 10 - General Motors VATS By-Pass Diagram; Tach Sensor Input

128-8111 10 of 20 A. Shock Sensor By Pass: If there is Shock Sensor used with an alarm system and it is not shunted during the Remote Start activation period,then vibration from the running vehicle can cause the alarm to trigger. In this case, connect the Light Blue Wire toterminal #86 of a external...

Page 11 - Tachometer Input Wiring Detail; Diesel Wait To Start Input; WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS; Pulsed Ground Output Before Start; Push-Button LED Programming Switch Assembly:

128-8111 11 of 20 Tachometer Input Wiring Detail 11 Green/Yellow Wire: Diesel Wait To Start Input The Green/Yellow wire of the 2 pin connector will connect to a diesel vehicles glow plug wire. When the unit receivesa start command, this wire must go to + 12 then to ground to allow the crank sequence...

Page 12 - Wire Ground Switched Door Lock Circuits:; Wire Ground Switched Door Lock/Unlock Wiring Detail; Wire Positive Switched Door Locks:; Wire Positive Switched Door Lock/Unlock Wiring Detail

128-8111 12 of 20 vehicle door lock / unlock circuits. The output of these wires has a maximum switching capability of 300mA. Manyvehicles today have factory door lock relays which can be connected directly to these outputs, however always confirmthat the factory relays in your particular vehicle do...

Page 13 - Pin Blue Connector :; Programming Switch; Pin White Auxiliary Output Connector :; Low Current Trunk Release Output (1Blue Wire Loaded); Multi Coil Pack Adapter:

128-8111 13 of 20 13 2 Pin Blue Connector : Programming Switch Route the gray and black wires in the 2 pin connector from the previously installed programming switch to the controlmodule and plug it into the mating blue connector on the side of the module. 2 Pin White Auxiliary Output Connector : Lo...

Page 15 - switch off. DO NOT attempt to remove the key.; REMEMBER TO RECONNECT THE BROWN/BLACK WIRE TEMPORARILY; MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERATIONS:

128-8111 15 of 20 The intent of the neutral start switch is to prevent the vehicle from starting while the gear selector is in any positionother than Park, or Neutral. When installing a Remote Start Device, it is imperative that the Yellow Starter wire beconnected to the ignition switch side of the ...

Page 16 - KEY IN SENSOR CIRCUITS:; Method 1; METHOD 1

128-8111 16 of 20 KEY IN SENSOR CIRCUITS: If the vehicle you are working on does not have or you cannot locate the ECM reference wire, there are two alternativesavailable. Although not preferred, the vehicle Key In Sensor may be reconfigured to allow a margin of safety and willprevent the vehicle wi...

Page 17 - METHOD 2

128-8111 17 of 20 METHOD 2 To connect to the key in sensor circuit as shown for method 2:A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch.B. Cut this wire and connect the ignition cylinder side to chassis ground.C. Locate the key in sensor switch wire ...

Page 18 - COMPLETING THE INSTALLATION:; under the dash board or in the engine compartment areas.; point these out to the customer.

128-8111 18 of 20 COMPLETING THE INSTALLATION: After you have confirmed the operation of the Audiovox Remote Start unit and tested all the safety features of thesystem: 1. If you have not done so already, place the red rubber handle cover over the handle of the control switch for ease of identificat...