Audiovox 128-7404A - Manuals

Audiovox 128-7404A – Manual in PDF format online.

Manuals:

Manual

Manual Audiovox 128-7404A

Summary

Page 2 - YOUR “CODE HOPPING“ TRANSMITTERS

128-7404A 2 of 24 Page 2  Protected Push Button Valet/Override Switch  7-Function LED-Arm / Disarm / Zone 1 / Zone 2 / Zone 3 / Valet / Arming  Intrusion Alert With Memory  Instant Siren Activation  Starter Disable Output  Additional Engine Immobilizer Output, (Optional Relay Required)  True ...

Page 3 - will not; ARMING THE SYSTEM - ACTIVE

128-7404A 3 of 24 Page 3 known as a code grabber, which will receive and store the signal from your keychain transmitter and re-transmit at a later time to disarm your system.Your Keeloq Code Hopping transmitters will change their signal every time the button is pressed, so when a thief grabs then r...

Page 4 - PROTECTION WHILE THE SYSTEM IS ARMED

128-7404A 4 of 24 Page 4  The dash mounted LED begins to flash slowly.  Parking Lights flash one time.  Siren will not sound. If the siren "chirped" three times, sometime after arming, the exclusive delayeddome light learn circuit has been programmed and the system detected a openentry po...

Page 5 - SILENT DISARMING

128-7404A 5 of 24 Page 5  Any mild impact to the vehicle’s glass will cause the alarm to sound a short series of warning tones.  Any strong impact to the vehicle’s glass will cause the alarm to trigger for the full 30 second alarm cycle. NOTE: If the optional interior illumination circuit was inst...

Page 6 - LED and Pushbutton Switch are one and the same.

128-7404A 6 of 24 Page 6  Parking Lights flash two times. If the parking lights flashed three times, then the alarm was triggered in yourabsence. Before turning the key on, examine the LED to identify which zone wastriggered.  Siren will not sound. If the siren sounds 4 chirps, then the alarm was ...

Page 7 - PROGRAMMING YOUR CUSTOM OVERRIDE CODE:

128-7404A 7 of 24 Page 7 2. Press and hold the valet pushbutton switch until the dash mounted LED turns on solid. The system will remain in the valet mode. 3. To return to normal operation, press and release the pushbutton switch any time the ignition is on. NOTE: Always remember to return the syste...

Page 8 - the need to hold the ARM / DISARM button for 2 seconds. To do this,

128-7404A 8 of 24 Page 8 Custom Code Programming Example: To Change the code from the factory pre-assigned code of 11 to “52” you would do the following: 1. Disarm the system by use of the transmitter or by use of the emergency override sequence. 2. Turn the ignition switch to the on position.3. Wit...

Page 10 - REMOTE STARTING THE VEHICLE

128-7404A 10 of 24 Page 10 4. Stage 3 (City Mode) In this mode, the pre-detect chirps will change from six pre-warning tones to a full 10 seconds of warning chirps. The full detect trigger duration will be reduced from 30 seconds to 15 seconds. NOTE: Setting the stage of the shock sensor will be eff...

Page 13 - TURBO TIMER MODE

128-7404A 13 of 24 Page 13 This security system has an additional feature that can be connected to a number of different optional accessories. Some of the more common uses for this channel are:  Remote Car Starter  Remote Window Closure  Remote Garage Door Interface To remotely operate the device...

Page 14 - TRANSCEIVER ICONS AND THEIR INDICATIONS; When Armed, Press the Disarm/Unlock button to

128-7404A 14 of 24 Page 14 every time the vehicle's engine is turned off. This feature requires the system to beset up for turbo timer during installation. Consult with your installation center to becertain this feature was activated and how long the vehicle will continue to run, 3,5, or 10 minutes ...

Page 15 - ADDITIONAL ICONS THAT MAY BE DISPLAYED ARE:

128-7404A 15 of 24 Page 15 will indicate count down timer based on the 5, 10, 15, or 20minute run time set up by your installation center. When the unitshuts off the exhaust indication will turn off and the transmitterwill play a melody. If text mode was selected, the screen willscroll the words Eng...

Page 16 - true if the transmitter is set for vibrate mode.

128-7404A 16 of 24 Page 16 true if the transmitter is set for vibrate mode. When the vehicle is armed, and a door is opened, or ajar, thetransmitter will chirp 3 times, the lights will flash, and the dis- play will indicate a door trigger as shown on the previous page. In the textmode the word Armed...

Page 18 - indicating that someone is calling you to the vehicle.

128-7404A 18 of 24 Page 18 the transmitter will emit a tone confirming the feature is active. Note: the unit will start once and run for the prescribed time. If you require more frequent starting please refer to auto start up timer mode shown earlier in this guide. NOTE: To insure accurate 24 Hour S...

Page 19 - TRANSMITTER FEATURE SELECTIONS:; our system is packaged with a two way confirm-

128-7404A 19 of 24 Page 19 NOTE: Your system is shipped with two transmitters, 1 two way, shown on the left and the one way transmitter, shown right. The one and two way transmitters are programmed from the factory with separate lock & unlock buttons, the trunk/ key icon button operates remote s...

Page 22 - THIS PAGE LEFT BLANK INTENTIONALLY

128-7404A 22 of 24 Page 22 THIS PAGE LEFT BLANK INTENTIONALLY

Page 23 - SYSTEM FUNCTIONS AT A GLANCE; DASH LED INDICATORS

128-7404A 23 of 24 Page 23 APS 998 SYSTEM FUNCTIONS AT A GLANCE DASH LED INDICATORS RAPID FLASHING = PASSIVE ARMING/ACTIVE REARMINGSLOW FLASHING = ARMED OFF = DISARMED ON SOLID = VALET MODE 3 FLASH...PAUSE = INTRUSION ZONE 3 2 FLASH...PAUSE = INTRUSION ZONE 2 1 FLASH...PAUSE = INTRUSION ZONE 1 SIREN...