AT&T TL7600 - Manuals

1 Getting started Avoid placing the headset charger too close to: • Communication devices such as: television sets, VCRs, or other cordless telephones. • Excessive heat sources.• Noise sources such as a window with traffic outside, motors, microwave ovens, refrigerators, or fluorescent lighting. • E...

2 Getting started IMPORTANT INFORMATION Use only the power adapter supplied with this product. To order a replacement power adapter, visit our website at www.telephones.att.com , or call 1 (800) 222-3111 . In Canada, dial 1 (866) 288-4268 . The power adapter is intended to be correctly oriented in a...

3 Getting started Battery installation Install the battery as shown below. For optimal performance, charge the headset battery for at least six hours before use. When not in use, recharge the headset by returning it to the headset charger. NOTE: Remove the ear hook from the headset (see page 11) bef...

4 Getting started Battery charging After installing the battery, charge the headset by placing it in the headset charger as shown below. The headset ON/OFF light is on when the headset is charging. 1. Insert the headset into the charging cradle. 2. Push the headset downward until the ON/OFF light on...

5 Getting started Registering the headset You must register your new TL7600 headset with one of the following models before use: AT&T DECT cordless headset TL7610/TL7611/TL7650/TL7651 (see page 6). You can register a maximum of two headsets to each headset base. -OR- A compatible AT&T DECT c...

6 Getting started Registering the headset To register a headset to the DECT headset base: Make sure the battery is properly installed in the headset (see page 3). The ON/OFF light flashes twice every five seconds to indicate the headset is not registered.Place the headset in the headset charger and ...

7 Getting started Registering the headset To register the headset to an AT&T DECT cordless telephone base: Make sure the battery is properly installed in the headset (see page 3). The ON/OFF light flashes twice every five seconds to indicate the headset is not registered.Place the headset in the...

8 Getting started Quick reference guide ON/OFF Press to make and/or answer a call, and to end a call.The light is on when the headset is charging in the headset base or charger. The light flashes slowly when you are on a call or flashes quickly when there is an incoming call (page 24). VOLUME + – Pr...

9 Getting started Headset attachments Over-the-ear hook To attach the ear hook to the headset: Remove any headset attachment connected to the headset.Insert the earpiece into the ear hook as shown in Figure 1.Press the ear hook onto the earpiece as shown in Figure 2. 4. Hook the headset onto the des...

10 Getting started Headset attachments Over-the-ear hook To adjust the headset to wear on the left or right ear: Hold the headset in your hand. Lift the hook upward as shown in Figure 1. Twist the hook 180˚ ��o��te���o�kwise�� �s show� i� �i���e ��� (counterclockwise) as shown in Figure 2. Push the ...

12 Getting started Headset attachments Over-the-headband To attach the headset to the headband for wearing on the left or right ear: Remove any headset attachment currently connected to the headset.Insert the earpiece into the headband ring as shown in Figure 1.Push the earpiece towards the headband...

14 Getting started The neckband ring is positioned for right-ear wearing when first purchased. To wear the headset on your left ear: Remove the ring from the neckband. Note the small opening in the plastic at the place where the ring meets the neckband. Then rotate the ring post up and through that ...

15 Getting started 3. Push the earpiece towards the neckband ring until it clicks into place as shown in Figure 3. 4. Place the neckband around your neck and over your ears.5. Adjust and rotate the angle of the headset until the microphone is pointing toward your mouth as shown in Figure 4. Headset ...

17 Operation Headset operation Making a call If you registered the expansion headset to a headset base, see the user’s manual for your headset base model TL7610/TL7611/TL7650/TL7651 for additional instructions. Visit www.telephones.att.com to view or download the user manuals. If you registered the ...

18 Operation Headset operation Answering a call on the headset Press ON/ OFF on the headset. Ending a call on the headset Press ON /OFF on the headset. Auto off A call ends automatically when you put the headset in the headset charger. NOTE: The headset does not have an external ringer. When you rec...

19 Operation Headset operation Temporary ring tone silencing Press MUTE/ FLASH to temporarily silence the ring tone in the headset earpiece. This silences the ring tone without disconnecting the call. The next incoming call rings normally at the preset volume. NOTE: If you have more than one headset...

20 Operation Options while on calls Volume controlTo adjust the listening volume: While on a call, press the VOLUME + – keys on the side of the headset to adjust the listening volume. NOTE: When the volume reaches the minimum or maximum setting, you hear three quick beeps. Call waiting If you subscr...

21 Operation Options while on calls Switching a call between handset and headset If you have registered the TL7600 to a TL7610/TL7611/TL7650/TL7651 headset base that is plugged into the telephone wall jack (installation option 1 or 2): To switch from the corded handset to a headset while on a call, ...

22 Operation Options while on calls Multiple headset/handset use Headset(s) and handset(s) on the same phone line can join an external call in progress. The number of headset(s) and handset(s) that can join may be limited by your telephone system. See your telephone user’s manual for more informatio...

23 Operation Headset alert tonesThree quick beeps. VOLUME + – keys are pressed when the volume is already at its highest or lowest setting.The headset is not registered and the headset ON/OFF button was pressed.The headset has gone out of range from the headset base during a call. • • • 1 short beep...

24 Operation ON/OFF light status On Headset is charging in the headset charger.Headset is trying to register to the headset base or telephone base.Headset may be too far from the headset base. •• • Flash Flashes slowly when incorrect battery is installed.Flashes three times, followed by a pause, the...

25 De-registration Replacing a headset You may need to de-register your headsets if: You have two registered headsets and need to replace one of them. -OR- You wish to change the designated headset number and/or the color of the ON/OFF light of your registered headsets. You must first de-register bo...

27 Maintenance and Troubleshooting My headset doesn’t work at all. • Make sure the power cord is securely plugged in. • Make sure the battery connector is securely plugged into the cordless headset. • Make sure the telephone line cord is securely and firmly plugged into the headset or telephone base...

28 Maintenance and Troubleshooting • If the previous suggestions do not work, disconnect the headset or telephone base from the telephone jack and connect a different phone. If there is no dial tone on that phone either, the problem is in your wiring or local service. Contact your local telephone co...

29 Maintenance and Troubleshooting • First try all the suggestions above.• Make sure you have a dial tone before dialing. The cordless headset may take a second or two to find the headset or telephone base and produce a dial tone. This is normal. Wait an extra second before dialing. • Eliminate any ...

30 Maintenance and Troubleshooting My cordless headset isn’t performing normally. • Make sure the power cord is securely plugged into the headset base or charger. Plug the unit into a different, working electrical outlet not controlled by a wall switch. • Move the cordless headset closer to the head...

31 Maintenance and Troubleshooting The batteries do not hold a charge. Troubleshooting • Make sure that the headset battery is installed and securely plugged into the connector. If the cordless headset is in the headset base or charger and the ON/OFF light on the headset does not come on, refer to T...

32 Maintenance and Troubleshooting • If you subscribe to high-speed Internet service (digital subscriber line - DSL) through your telephone lines, you must install a DSL filter between the telephone line cord and the telephone wall jack. The filter prevents noise and caller ID problems caused by DSL...

34 Maintenance and Troubleshooting • Test a working phone at the phone jack. If another phone has the same problem, the problem is the phone jack, wiring or service. Contact your local telephone company (charges may apply). • Other electronic products can cause interference with your cordless headse...

35 Maintenance and Troubleshooting • Other electronic products can cause interference with your cordless headset. Try installing your headset as far away from the following electronic devices as possible: television sets, VCRs, or other cordless telephones. • Do not install this headset near a micro...

36 Maintenance and Troubleshooting The ON/OFF light on the headset is off while charging. • Make sure the power and line cords are plugged in correctly and securely.Make sure that the battery connector is securely plugged into the cordless headset.Push the headset downwards in the charging cradle un...

37 Maintenance and Troubleshooting I cannot register the headset. For registration to a cordless telephone: You must be using a compatible AT&T DECT 6.0 cordless telephone. Visit www.telephones.att.com for a list of compatible telephones.Your cordless telephone has a maximum number of handsets t...

38 Maintenance and Troubleshooting Common cure for electronic equipment. If the unit does not seem to be responding normally, try putting the cordless headset in its base or charger. If it does not seem to respond, do the following (in the order listed):• Disconnect the power to the headset charger ...

39 Maintenance and Troubleshooting Important safety information This symbol is to alert you to important operating or servicing instructions that may appear in this user’s manual. Always follow basic safety precautions when using this product to reduce the risk of injury, fire, or electric shock. Sa...

40 Maintenance and Troubleshooting Important safety information Replace batteries only as described in your user’s manual. Do not burn or puncture batteries — they contain caustic chemicals. This power adapter is intended to be correctly oriented in a vertical or floor mount position. The prongs are...

41 Maintenance and Troubleshooting Important safety information Rechargeable batteries: This product contains nickel- cadmium, nickel-metal hydride or lithium-ion rechargeable batteries. Exercise care in handling batteries in order not to create a short circuit with conductive material such as rings...

42 Maintenance and Troubleshooting Important safety information To prevent fire or shock hazard, do not expose this product to water or any type of moisture.Observe proper polarity orientation between the battery and metallic contacts.Do not disassemble your telephone. There are no user-serviceable ...

43 Maintenance and Troubleshooting Maintenance Taking care of your headset Your cordless headset contains sophisticated electronic parts, so it must be treated with care.Avoid rough treatment.Place the headset down gently. Save the original packing materials to protect your headset if you ever need ...

44 Appendix A FCC Part 68 and ACTA This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment contains, among other things, a product identifier in the ...

46 Appendix A FCC Part 68 and ACTA Industry Canada Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation.The term ‘’IC:‘’ before the certifi...

47 Appendix B FCC Part 15 This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a resid...

49 Appendix C Limited warranty The AT&T brand is used under license - any repair, replacement or warranty service, and all questions about this product should be directed to: In the United States of America, visit www.telephones.att.com or call 1 (800) 222-3111 . In Canada, call 1 (866) 288-4268...

51 Appendix C Limited warranty PRODUCT returned without valid proof of purchase (see item 6 below); -or-Charges for installation or setup, adjustment of customer controls, and installation or repair of systems outside the unit. 5. How do you get warranty service? To obtain warranty service in the Un...

53 Appendix C Operating range This cordless headset operates within the maximum power allowed by the Federal Communications Commission (FCC). Even so, this headset and headset base can communicate over only a certain distance — which can vary with the locations of the headset base and headset, the w...

54 Index A AC adapter, 2 Alert tones, 23 Answering calls, 18 Auto off, 18 B Battery charging, 4 Battery installation, 3 C Call waiting, 20 D De-registration, 25 DSL, 1, 32 E Ear hook headset attachment, 9-11 Ending calls, 18 F Flash (switch hook flash), 20 H Headband headset attachment, 12-13 Headse...

55 Index Index T Technical specifications, 53 Temporary ring tone silencing, 19 Troubleshooting, 27-38 V Volume controls, 20 W Warranty, 49-52