AT&T TL7000 - Manuals

1 Switch hook presser When LIFTER MODE is on, pressing the ON/OFF key on the headset raises and lowers the switch hook presser, and holds down the switch hook when the phone is not in use. ALERT ON/OFF Turns the ring detector on or off. When the ringer detector is turned off, the cordless headset do...

Lifter arm height control Pushes / to adjust the height of the lifter arm. 2 Getting started Quick reference guide - Handset lifter Small lifter pad Holds the earpiece of the corded telephone handset.

3 Getting started Handset lifter installation The TL7000 handset lifter (lifter) works with the TL7610 or the TL7650 cordless headset to provide a complete communication solution. The lifter raises and lowers the handset to make and end phone calls. The ring detector provides an incoming call indica...

4 Getting started Handset lifter installation 5. Pick up the lifter, turn it over, and peel the paper from the adhesive tape. 6. Carefully return the lifter to the same position that you noted before and press down. 7. Follow the headset base installation steps on pages 6-10. 8. Remove the handset f...

It may take some adjustments and testing to find the right position for the lifter. For the lifter to work properly, the switch hook must release completely when you press the ON /OFF button on the headset. The switch hook must also be pressed all the way when you press the ON/ OFF button on the hea...

6 Getting started Handset lifter installation Connect the headset base The cords provided with your lifter have colored labels attached to help you plug them into the headset base. The back of the headset base has color-coded dots above the jacks, and the jacks’ names on the rear bottom plastic piec...

Getting started Handset lifter installation 7 Before installing the headset base: Remove the rear bottom piece of the headset base by pushing it away from the base (as shown in Figure 2). Install the headset base as shown on pages 9-10. After completing the headset base installation, slide the rear ...

9 Getting started Handset lifter installation Headset base installation with lifter (see Figure 4) 1. Plug one end of the telephone line cord (provided with your telephone) into the telephone jack. 2. Plug the other end of the telephone line cord into the wall jack. 3. Make sure the small end of the...

11 Getting started Ring detector installation Ring detector plug Install the ring detector 1. Insert the ring detector plug into the RING DETECT jack on the lifter. 2. Remove the paper from the adhesive tape on the ring detector sensor. 3. Stick the adhesive tape as close to the telephone speaker as...

Getting started Ring detector installation Adjust the sensitivity level The ring detector sensitivity level is designed to work with most corded telephones. However, the ring detector may need some adjustments to recognize less common telephone ring tones. To adjust the ring detector sensitivity whi...

STATUS light The light is blue when the lifter is not in use and the ring detector is turned on. The light is red when the lifter is not in use and the ring detector is turned off. The light quickly flashes in blue when the ring detector senses an incoming call.The light flashes slowly in blue when ...

14 Make a call with the corded handset As indicated in the figure, lifting the handset causes the lifter arm to raise and release the switch hook. You will hear a dial tone through the handset. You can dial normally using the telephone dial pad. Handset lifter operation Handset lifter operation Afte...

15 Handset lifter operation Handset lifter operation Make and answer calls with the handset lifter and cordless headset You can use the cordless headset to make calls, answer calls and end calls without using the corded handset. Answer a call• Press ON /OFF on the headset to answer an incoming call....

17 Troubleshooting Troubleshooting If you have difficulty with your handset lifter, please try the suggestions below. For Customer Service, visit our website at www.telephones.att.com , or call 1 (800) 222–3111 . In Canada dial 1 (866) 288-4268 . The switch hook presser of the lifter doesn’t raise a...

21 Maintenance and safety Maintenance Taking care of your handset lifter Your lifter contains sophisticated electronic parts, so it must be treated with care.Avoid rough treatment.Place the lifter down gently. Save the original packing materials to protect your lifter if you ever need to ship them. ...

The AT&T brand is used under license - any repair, replacement or warranty service, and all questions about this product should be directed to: In the United States of America, visit www.telephones.att.com or call 1 (800) 222-3111 . In Canada, call 1 (866) 288-4268 . What does this limited warra...

PRODUCT returned without valid proof of purchase (see item 6 below); -or-Charges for installation or setup, adjustment of customer controls, and installation or repair of systems outside the unit. How do you get warranty service? To obtain warranty service in the United States of America, visit www....

c. Provide your name, complete and correct mailing address, and telephone number. Other limitations This warranty is the complete and exclusive agreement between you and the manufacturer of this AT&T branded PRODUCT. It supersedes all other written or oral communications related to this PRODUCT....

27 Index Index A Alert tones, 1, 11-13, 19 Answer calls, 15, 16 Anti-slip pad, 5 Audio adjustment, 10 C Color label, 6, 7 D DSL, 6, 8 E End calls, 15, 16 F Flash, 1, 12, 13 H Headset base, 1, 7-10, 14 I Installation, 3-13 L Large lifter pad, 3, 5 Lifter arm, 1, 2, 5, 6, 14, 18 height control, 2, 3, ...